Panasonic E 37 V Dome Camera Operation Manual

							                                              
 56 
 
 
Figure 4-36 
When login password keep been wrong for a few times, unauthorized access alarm occurs. This 
operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account 
will be locked.  
 
 
Figure 4-37 
4.3 Storage Management  
4.3.1 Schedule  
Before schedule setup, user must set record mode is auto or manual.  
Note: 
If record mode in record control is off, then device will not snapshot according to schedule.  
4.3.1.1 Record Schedule  
						

							                                              
 57 
Record schedule steps: 
Step 1. Click on Record Schedule, see Figure 4-38. 
 
Figure 4-38 
Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 4-39. 
 Set period according to actual need. There are six periods available each day.  
 By checking or unchecking, you can add or delete three types of record schedule: General, Motion, 
and Alarm.  
Note: 
Period setup can be done by dragging in record schedule interface while not releasing left mouse.  
 
Figure 4-39 
Step 3.  Click on OK, return to record schedule interface. See Figure 4-40.  
 Green color stands for the general record/snapshot.  
						

							                                              
 58 
 Yellow color stands for the motion detect record/snapshot. 
 Red color stands for the alarm record/snapshot.  
 
Figure 4-41 
Step 4. In record schedule interface, click on OK. System prompts it is successfully saved.  
 
4.3.1.2 Snapshot Schedule 
Snapshot setup as: 
Step 1. Click on Snapshot Schedule tab, see Figure 4-42. 
Figure 4-42  
						

							                                              
 59 
 
Step 2. From Monday to Sunday select snapshot time, click on setup on the right. See Figure 4-43 
 Set snapshot period according to actual need. There are six periods available each day.  
 By checking or unchecking, user can add or delete three types of snapshot schedule: General, 
Motion and Alarm.  
Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left 
mouse.  
 
Figure 4-43 
 
Step 3. Click on OK, return to snapshot schedule interface. See Figure 4-44.  
 Green color stands for the general record/snapshot. 
 Yellow color stands for the motion detect record/snapshot. 
 Red color stands for the alarm record/snapshot.  
  
						

							                                              
 60 
 
Figure 4-44 
Step 5. In snapshot interface, click on OK. System prompts it is successfully saved.  
 
4.3.1.3 Holiday Schedule 
Holiday schedule can set specific date as holiday.  
Step 1. Click on Holiday Schedule tab, see Figure 4-45. 
 
 
Figure 4-45  
						

							                                              
 61 
 
Step 2. Select date to set as holiday. The selected date will be highlighted in yellow.  
Step 3. Check Record/Snapshot, click on Save. System prompts it is successfully saved.  
Step 4. Check Record Schedule/Snapshot Schedule interface, click on setup next to Holiday, refer to 
setup of Monday to Sunday.  
Step 5. Complete setup of holiday, then it records/snapshots according to date in holiday schedule.  
 
4.3.2 Destination  
4.3.2.1 Path 
The destination interface is shown as in Figure 4-46 
Path can config record and snapshot storage path. There are three options: Local, FTP and NAS. You 
can only select one mode. System can save according to the event types. It is corresponding to the 
three modes (general/motion/alarm) in the Schedule interface. Please check the box to enable the save 
functions.  
Note: Only device supports SD card has local. 
 
Figure 4-46 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Event 
Type  
It includes: scheduled, motion detect and alarm.   
Local  It saved in the SD card.  
FTP  It saved in the FTP server.  
NAS It saved in NAS disk.  
 
4.3.2.2 Local 
The local interface is shown as in Figure 4- 47.   
						

							                                              
 62 
Here you can view local Micro SD card or NAS disk information. You can also operate the read-only, 
write-only, hot swap and format operation.  
 
Figure 4- 47 
 
4.3.2.3 FTP 
The FTP interface is shown as in Figure 4- 48. 
You need to check the box to enable the FTP function. When network disconnect occurred or there is 
malfunction. Emergency storage can save the record/snapshot picture to the local SD card.  
 
Figure 4- 48 
 
4.3.2.4 NAS  
						

							                                              
 63 
You need to check the box to enable the NAS function. Select NAS storage, fill in NAS server 
address and corresponding store path, then you can store video file or pictorial information in the NAS 
server.  
Select NAS storage as to same file to NAS disk. See Figure 4- 49. 
 
Figure 4- 49 
 
Parameter Function 
Server Address Set IP address of NAS server. 
Remote 
Directory 
Set storage directory, videos and pictures can be stored in to corresponding server 
directory. 
 
4.3.3 Record control  
The record control interface is shown as in Figure 4- 50. 
 
Figure 4- 51 
Please refer to the following sheet for detailed information.   
						

							                                              
 64 
Parameter  Function  
Pack 
Duration 
Here you can select file size within 1min~120min. Default setup is 8 
minutes. 
Pre-record  Please input pre-record value here.  
For example, system can record the four seconds video in the buffer. 
The record begins from the fifth second.  
Note: 
Configure pre-record time, when alarm or motion detection occurs, if 
there is no record, system will record the preceding n seconds 
record.   
Disk Full There are two options: stop recording or overwrite the previous files 
when HDD is full. 
 Stop: Current working HDD is overwriting or current HDD is full, 
it will stop record.  
 Overwrite: Current working HDD is full; it will overwrite the 
previous file. 
Record 
mode  
There are three modes: Auto/manual/close.   
Record 
stream  
There are two options: main stream and sub stream.  
 
 
4.4 System  
4.4.1 General  
The General interface is shown as in Figure 4- 52. 
 
Figure 4- 52 
Please refer to the following sheet for detailed information.   
						

							                                              
 65 
Parameter  Function  
Device 
Name 
It is to set device name.  
Note: Different devices have different names.  
Video 
Standard 
This is to display video standard such as PAL. 
 
Language  You can select the language from the dropdown list.  
 
The date and time interface is shown as in Figure 4-53. 
 
Figure 4-53 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Date format Here you can select date format from the dropdown list. 
Time 
Format 
There are two options: 24-H and 12-H. 
Time zone  The time zone of the device.  
System 
time  
It is to set system time. It becomes valid after you set.  
Sync PC You can click this button to save the system time as your PC current 
time.