Panasonic E 37 V Dome Camera Operation Manual

							                                              
 6 
2 Live 
After you logged in, you can see the live monitor window. See  
Figure 2-1. 
 
Figure 2-1  
There are four sections: 
 Section 1: Encode setup bar 
 Section 2: System menu  
 Section 3: Window function option bar 
 Section 4: Window adjust bar  
 
2.1 Encode Setup  
The encode setup interface is shown as in Figure 2-2. 
 
 
Figure 2-2  
Please refer to the following sheet for detailed information.  
2 
3 1 
4  
						

							                                              
 7 
Parameter  Function  
Main stream  Streaming media protocol connection, under main stream config, 
monitor video or not. Generally for storage and monitor.   
Sub (Extra) 
stream 1 
Streaming media protocol connection, under sub stream 1 
config, monitor video or not. When network bandwidth is 
insufficient, it substitutes main stream for monitoring.  
Sub (Extra) 
stream 2 
Streaming media protocol connection, under sub stream 2 
config, monitor video or not. When network bandwidth is 
insufficient, it substitutes main stream for monitoring. 
Protocol  You can select stream media protocol from the dropdown list.  
There are three options: TCP/UDP/Multicast 
 
2.2 System Menu  
System menu is shown as in Figure 2-3. 
Please refer to chapter 2 Live, chapter 3 PTZ, chapter 4 Playback, chapter 5 Setup, chapter 6 Alarm, 
chapter 7 Log out  for detailed information.   
 
Figure 2-3  
2.3 Video Window Function Option  
The interface is shown as below. See Figure 2-4. 
 
 
 
 
Figure 2-4  
Please refer to the following sheet for detailed information.  
SN Parameter Function  
1 Zoom in  When the video is in the original status, click it you can 
select any zone to zoom in. In the non-original status, 
you can drag the zoom-in zone in specified range. Right 
click mouse to restore previous status.  
 Click it; you can use the middle button of the mouse to 
zoom in/out the video size.  
1        2      3     4      5       6         
						

							                                              
 8 
2 Snapshot Click on the button to snapshot, save picture to path in Ch 
5.1.2.5. 
3 Triple snap  Click it, system can snap at 1f/s. All images are saved to path 
in Ch 5.1.2.5. 
4 Record Click it, system can record. All images are saved to path in Ch 
5.1.2.5. 
5 Easy focus  Click it, you can see there are two parameters on the preview 
video：AF Peak and AF Max. 
AF Peak: It is to display the video definition during the focus 
process.  
AF Max: It is the most suitable value for the video definition.  
The close the AF Peak and AF Max is, the better the focus 
effect is.  
6 Help  Click it to open help file.  
 
2.4 Video Window Setup   
The interface is shown as in Figure 2-5. 
 
 
 
 
Figure 2-5 
  
2.4.1 Image Adjustment 
See Figure 2-6 for image adjustment. 
1     2      3     4     5      6         
						

							                                              
 9 
 
Figure 2-6 
 
Click this button to display/hide image control interface. Click it to open picture setup interface. This 
interface is on the top right pane.  
 
Please refer to the following sheet for detailed information.  
Parameter Function  
Video 
setup   It is to adjust monitor video 
brightness.  
Note: 
 All the operations here apply 
to WEB end only. 
 Please go to Setup-
>Camera->Conditions to 
adjust corresponding items.  
 It is to adjust monitor video 
contrastness. 
 It is to adjust monitor video 
hue. 
 It is to adjust monitor video 
saturation. 
Reset 
R
e 
Restore brightness, 
contrastness saturation and 
hue to system default setup. 
 
2.4.2 Original Size 
Click this button to go to original size. It is to display the actual size of the video stream. It depends on 
the resolution of the bit stream. 
 
2.4.3 Full Screen 
Click it to go to full-screen mode.  Double click the mouse or click the Esc button to exit the full screen. 
  
						

							                                              
 10 
2.4.4 Width and Height Ratio 
Click it to restore original ratio or suitable window.  
 
2.4.5 Fluency Adjustment 
There are three levels of fluency for you to select (real-time, normal, fluent). The default is normal.  
 
2.4.6 Focus zoom 
Click this button and the focus zooming interface appears on the right of preview interface, as shown in 
Figure 2-7, click left mouse button to adjust focus zooming configuration.  
Note:  
· The product series which support motorized zoom, synchronous focus and back focus have this 
button.    
· Auto-focus after zoom and focus adjustment.  
						

							                                              
 11 
3 Playback 
Web client playback supports video playback and picture playback.  
Note: 
Before playback, user shall set storage management  
3.1 Playback  
The playback interface is shown as in Figure 3- 1. 
 
 
Figure 3- 1 
 
There are four sections: 
 Section 1: Function of play 
 Section 2: Playback file 
 Section 3: Play time cut 
 Section 4: Record type 
 Section 5: Progress bar 
 Section 6: Assistant function 
 
3.1.1 Function of Play 
1 
4 5 
3 
6 
2  
						

							                                              
 12 
The function of play is shown as in Figure 3- 2. 
 
 
 
 
 
Figure 3- 2 
Parameter Function 
① Play When  you  see  this  button,  it  means  pause  or  not  played  record.  Click  on  this 
button, switch to normal play status.  
② Stop Click this button to stop playing.  
③ Play  by 
frame 
Click on this button to go to next frame.  
Note:  
You shall pause record when you use this function.  
④ Slow Click on this button to play slowly.  
⑤ Quick Click on this button to play quickly.  
⑥ Silent When  this  button  displays,  it  means  audio  is  silent.  Click  on  this  button  to  switch 
back to normal.  
⑦ Volume Click on left mouse to adjust volume.  
 
3.1.2 Playback File 
In calendar, blue date represents data currently has video record or snapshot. See Figure 3-3. 
1       2      3      4       5           6            7  
						

							                                              
 13 
 
Figure 3-3 
 
Parameter Function 
File Type  Select “dav”, as video playback.  
 Select “jpg” as picture playback.  
Data Source Default is SD card.  
 
Step 1K Click on data in blue, time axis displays record file progress bar in color. While, green represents 
normal record, yellow represents motion detect record, red represents alarm record, and blue 
represents manual record.  
Step 2K Click on certain time on progress bar, playback starts from this time.  See Figure 3- 4. 
 
Figure 3- 4 
Step 3. Click on file list, select date file will be displayed in list.  
Step 4. Double click on file in list, playback this file and display file size, start time and end time.  
See Figure 3-5.  
						

							                                              
 14 
 
Figure 3-5 
 
Parameter Function 
Search It means records within searched start time and end time on the date. 
Record 
Download 
Format 
There are two formats:  dav, mp4.  
						

							                                              
 15 
Parameter Function 
Download 
 Record type is “dav”, click on download button to download file to local.  
 Record  type  is  “mp4”,  click  on  download  button  and  download  file  to  path  in 
Ch 5.1.2.5. 
Note: 
System does not support download and playback of MP4 file.  
Back Click on back button to go to calendar interface.  
 
 
3.1.3 Playback Cut 
Note: 
Playback cut function will automatically pause playing record as playback cut and playback cannot be at 
the same time.  
Step 1. Click on start time to cut on time axis. This time must be within progress bar range.  
Step 2. Move mouse to cut icon . You will be ask to select start time. Click on cur icon  as 
finish cutting.  
Step 3. Click on playback cut end time on time axis. This time must be within progress bar range.  
Step 4. Move mouse to cut icon, you will be asked to select end time. Click on cut icon  as 
finish cutting. 
Step 5. Click on Save button to save file cut to path. See Figure 3- 6. 
 
Figure 3- 6 
3.1.4 Record Type 
After checking record file type, only selected file will be displayed in progress bar and file list. Users can 
also select the record type to be displayed via the dropdown box which is above the file list. See Figure 
3- 7. 
 
 
Figure 3- 7 
 
3.1.5 Progress Bar