Panasonic E 37 V Dome Camera Operation Manual

							                                              
 46 
 
Figure 4-25 
4.1.12 Multicast 
The multicast interface is shown as in Figure 4-26. 
Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data 
packet, multiple-cast is the best option to reduce the broad width and the CPU load.  The source host 
can just send out one data to transit. This function also depends on the relationship of the group 
member and group of the outer.  
Note: 
 Open preview, streaming media protocol, select multicast, and monitor via multicast format.  
 Here you can set multicast address and port. You also need to go to Live interface to set the 
protocol as Multicast.  
  
						

							                                              
 47 
 
 
Figure 4-26 
 
Please refer to the following sheet for detailed information.  
 
4.1.13 802.1x 
802.1x (port based network access control protocol) supports manual selection of authentication 
method to control if device connected to LAN can join the LAN. It well supports authentication, charging, 
safety and management requirement of network. 
             
 
 
 
 
 
 
Parameter  Function  
Enable Select to enable multicast function. Main stream and sub stream cannot be 
used at the same time.  
Multicast address Main/sub stream multicast default address is 224.1.2.4 and its range is 
224.0.0.0～239.255.255.255. 
Port Multicast port. Main stream is 40000, sub stream is 40002 and the range is 
1025～65534.  
						

							                                              
 48 
 
 
Figure 4-27 
 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Authentication PEAP (protected EAP protocol).   
Username It needs the username to login, which is authenticated by the 
server. 
Password Please input password here.  
 
4.1.14 QoS 
The QoS interface is shown as below. See Figure 4-28. 
Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and 
jam problem and etc. For the network service, the quality of service includes the transmission bandwidth, 
delay, the packet loss and etc. We can guarantee the transmission bandwidth, lower the delay, reduce 
the loss of the data packet and anti-dither to enhance the quality.  
We can set the DSCP (Differentiated Services Code Point) of the IP to distinguish the data packet so 
that the router or the hub can provide different services for various data packets. It can select the 
different queues according to the priority (64 different priority levels) of the packets and select the 
bandwidth of the each queue. Level 0 is the lowest, and level 63 is the highest. It can also discard at the 
different ratio when the broad bandwidth is jam.  
  
						

							                                              
 49 
 
Figure 4-28 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Real-time 
monitor  
The value ranges from 0 to 63. The router or the switcher can 
provide different service for various data packets.  
Command  The value ranges from 0 to 63. The router or the switcher can 
provide different service for various data packets. 
Enable 
Wireless QoS 
Check it to enable QoS. 
 
4.2 Event  
4.2.1 Video detect 
4.2.1.1 Motion Detect  
The motion detect interface is shown as in below. 
 
 
 
 
 
 
  
						

							                                              
 50 
 
Figure 4-29 
 
 
Figure 4- 30 
 
  
						

							                                              
 51 
 
Figure 4- 31 
Please refer to the following sheet for detailed information.  
Parameter Function  
Enable  You need to check the box to enable motion detection function.  
Enable video 
mask detection  
You need to check the box to enable video mask detection alarm. 
Enable defocus 
detection  
You need to check the box to enable defocus detection alarm. 
Working Period  Here you can set arm/disarm period. Click on set button to open period 
setup menu.   
There are six periods every day for setup and you must check box in front 
of each period to enable it.  
Note: Period setup can be done by dragging mouse while not release left 
mouse.  
Anti-dither System only memorizes one event during the anti-dither period. The value 
ranges from 0s to 100s.  
						

							                                              
 52 
Parameter Function  
Area  Here you can set motion detection region and its sensitivity and area. (The 
higher the sensitivity is, the easier to trigger motion detect; the smaller the 
area, the easier to trigger motion detect.) The default covers all regions. 
You must click on save before enabling your setup.  
Record Check it and so when alarm occurs, system will auto record. You shall set 
record period in Storage>Schedule and select auto record in record control 
interface.  
Record Delay  System can delay the record for specified time after alarm ended. The 
value ranges from 10s to 300s. 
Relay out Enable alarm activation function. You need to select alarm output port so 
that system can activate corresponding alarm device when alarm occurs.   
Alarm Delay System can delay the alarm output for specified time after alarm ended. The 
value ranges from 10s to 300s.  
Send Email  If you enabled this function, System can send out email to alert you when  
alarm occurs and ends. User can set email address in Network>SMTP. 
Audio linkage Check it and the system will play alarm audio file when alarm occurs. Users 
can set the recorded or uploaded audio file in “camera setting ＞ audio ＞ 
alarm audio”. 
Flash linkage Check it and the flash will be on when alarm occurs, and the flash will 
 be off until the end of alarm after corresponding delay.     
PTZ   Here you can set PTZ movement when alarm occurs. Such as go to 
preset x when there is an alarm. 
 The event type includes: preset, tour and pattern.  
Snapshot  You need to check the box here so that system can backup motion detection 
snapshot file. You shall set snapshot period in Storage>Schedule. 
 
See Figure 4-32.  
						

							                                              
 53 
 
Figure 4-32 
Different colors represent different areas. Each area can set different detection zones. Detection zone 
can be irregular and discontinuous.  
Please refer to the following sheet for detailed information.  
 
Parameter Function  
Name Default area name includes Region1, Region2, Region3, 
Region4 and custom.  
Sensitivity  It is sensitivity of brightness as motion detection is more possible 
to be trigger with higher sensitivity. You can set up different 
sensitivities. The range is 0~100. The recommenced value is 
30~70.  
Area threshold It is to check the relationship between object and its area. The 
lower the area threshold, the easier to trigger motion detection. 
You can set up different threshold for each area. The range is 
0~100. The recommenced value is 0~10. 
Waveform Red means motion detect is triggered. Green means motion 
detect is not triggered. 
Delete all Clear all the detection areas with color.   
						

							                                              
 54 
Delete Delete selected area.  
 
4.2.2 Abnormity 
Abnormity includes No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict and 
Unauthorized Access.  
Note: 
Only device with SD card function has these three statuses: No SD card, capacity warning, and SD card 
error.  
Device without SD card function does not have the above three statuses. See Figure 5-61 to Figure 4-
33.  
 
Figure 4-33 
 
 
Figure 4-34  
						

							                                              
 55 
 
 
Figure 4-35 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Enable Check to alarm when SD card is abnormal.  
Relay-out Check to enable relay-out alarm.  
Relay out 
delay  
The alarm output can delay for the specified time after alarm stops. The 
value ranges from 10s to 300s. 
Note: 
No SD card, capacity warning, SD card error, relay-out delay all start 
from alarm occurs.  
Send 
email  
After you enabled this function, the system can send out email to alarm 
the specified user.  
This function is invalid when network is offline or IP conflict occurs. 
SD Card 
Capacity 
Limit 
User can set SD card capacity that is left free. When SD card space left 
is smaller than this limit, alarm occurs.  
When device is offline or IP conflicts, the abnormal alarm is similar with case of SD card error.