Panasonic E 37 V Dome Camera Operation Manual

							                                              
 26 
 
Profile management has three modes: normal, full time and schedule. If you select normal, the video will 
be configured as normal as in Figure 4-2.  
 
 
Figure 4-2 
If you select full time, you must select either day or night, and the video will be configured accordingly 
as in Figure 4-3 and Figure 4-4.  
 
Figure 4-3 
 
Figure 4-4 
  
						

							                                              
 27 
If you select schedule, you can decide detained day time interval and night time interval as in Figure 4-
5. You can set 0:00 ~ 12:00 as day, and 12:00 ~ 24:00 as night. 
 
 
Figure 4-5 
Important 
 The setup becomes immediately effective after you click on OK. 
 You can see WDR option only if your camera supports WDR function. System does not support 
long-time exposure or low noise mode.  
4.1.2   Zoom and Focus  
Note: Only motorized vari-focal devices support focus and zoom function.  
 
 
Figure 4- 6  
						

							                                              
 28 
Parameter Function  
Zoom  
Adjust the focal length of the lens by clicking or long press “+” 
or “-“.   
Speed  can  be  used  to  adjust  the  length of  one  step  by  single 
click.  
Note:  After  adjusting  zoom,  the  device  will  focus 
automatically.  
Focus 
Adjust the lens definition by clicking or long pressing “+” “-“.  
Speed  can  be  used  to  adjust  the  length of  one  step  by  single 
click.  
Auto Focus Click to adjust the image definition automatically. 
Reset  
Reset the lens to 0 position, which can be used to remove the 
accumulative error for the lens.   
Note:  
Please reset when adjusting unclear image or using zoom 
and focus for many times.  
Refresh  After  hardware  zoom,  synchronize  the  position  of  lens  and 
dragging block of zoom and focus.  
 
4.1.3 Video  
4.1.3.1 Video bit stream  
The video bit stream interface is shown as below. See Figure 4-7. 
  
						

							                                              
 29 
 
Figure 4-7 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Sub Stream Enable  Please check the box here to enable extra stream 
function.   
This function is enabled by default.  
Code-Stream Type  ACF means using different fps to record.  
There are two options: VBR and CBR.  
Please note you can set video quality in VBR mode.  
Note:  
WEB interfaces don’t support motion detect and alarm 
code stream setting. 
Encode mode  There are five options: H.264 Emain profile standard, 
H.264H (high profile standard), H.264B (Baseline 
Profile), H.265 (main profile standard) and MJPG 
encodeK 
 The H.264, H.264H both are H264 bit stream. 
H.264 is the Main Profile encode and you need to 
enable the sub stream function in your camera and 
set the resolution as CIF. Then you can monitor via 
the Blackberry cell phone.  
 The H.265 is the main profile encode mode.  
 MJPEG: In this encode mode, the video needs to 
large bit stream to guarantee the video definition. 
You can use the max bit stream value in the 
recommend bit to get the better video output effect.  
Resolution  There are multiple resolutions. You can select from the 
dropdown list.  
For each resolution, the recommended bit stream value 
is different. 
Note: When video is under rotating status, you cannot 
set resolution higher than 1080P (excluding 1080P). 
Frame Rate (FPS) PAL: 1～25f/s，1-50f/s  NTSC: 1～30f/s or 1~60f/s. 
The frame rate may vary due to different resolutions.  
Bit Rate Type  There are two options: VBR and CBR.  
Please note, you can set video quality in VBR mode.  
Under MJPEG mode, only CBR is available.  
Recommended Bit  Recommended bit rate value according to the resolution 
and frame rate you have set.   
						

							                                              
 30 
Parameter  Function  
Bit Rate   In CBR, the bit rate here is the max value.  In 
dynamic video, system needs to low frame rate or 
video quality to guarantee the value.  
 The value is null in VBR mode.  
 Please refer to recommend bit rate for the detailed 
information.  
I Frame  Here you can set the P frame amount between two I 
frames. The value ranges from 1 to 150.  Default value 
is 50. 
Recommended value is frame rate *2. 
Watermark Settings By calibrating watermark, to see if video is modified. 
Select Watermark function. Default watermark is Digital 
CCTV.  
Watermark character can only be number, letter, _, - 
within 128 characters.  
 
4.1.3.2 Snapshot  
The snapshot interface is shown as in Figure 4- 8. 
 
Figure 4- 8 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Snapshot type  There are two modes: general (schedule) and Event (activation). 
Image size  It is the same with the resolution of snapshot (main stream or sub 
stream).  
Quality  It is to set the image quality. There are six levels.  
Interval  It is to set snapshot frequency. Optional1~7s/picture, customized.   
						

							                                              
 31 
 
4.1.3.3 Video Overlay  
The video overlay interface is shown as in Figure 4- 9. 
 
Figure 4- 9 
 
Figure 4- 10  
						

							                                              
 32 
 
Figure 4-11 
 
Figure 4-12 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Privacy mask  Here you can privacy mask the specified video in the 
monitor video.  
 System max supports 4 privacy mask zones.  
						

							                                              
 33 
Time Title  You can enable this function so that system overlays time 
information in video window.  
 You can use the mouse to drag the time tile position.  
Channel Title   You can enable this function so that system overlays 
channel information in video window. 
 You can use the mouse to drag the channel tile position. 
Overlay  You can enable this function to display overlay picture. 
Click on disable to turn it off.  
 Click on Upload Picture to overlay local picture into 
monitoring window. You can drag the yellow box to move 
it.  
Note: 
You cannot enable location and overlay at the same time.   
 
4.1.3.4 ROI  
Note: Some series don’t support ROI setup function.   
 
Figure 4-13 
  
						

							                                              
 34 
 
 
Figure 4-14  
 
Parameters Note  
Enable  Check “Enable”, then it will display the ROI in the video monitoring window; 
Check “Disable”, then it won’t display.                           
Image 
Quality  
 Set the image quality of ROI, ranging from 1～6, default is 6.  
Note:  
For fisheye device, it ranges from 1~6 (best), default is 6 (best) 
 Able to set area block, max 4 areas.  
 
4.1.3.5 Path  
The storage path interface is shown as below. 
Here you can set snap image saved path and the record storage path. 
 The default monitor image path is C:\Documents and Settings\Admin\WebDownload\Snapshot.  
 The default monitor record path is C:\Documents and Settings\Admin\WebDownload\LiveRecord. 
 The default playback snapshot path is C:\Documents and 
Settings\Admin\WebDownload\PlaybackSnapshot. 
 The default playback download path is C:\Documents and 
Settings\Admin\WebDownload\PlaybackRecord.  
 The default playback cut path is: C:\Documents and Settings\Admin\WebDownload\VideoClips.  
						

							                                              
 35 
Note: 
Admin is locally logged in PC account.  
Please click the Save button to save current setup.  
 
Figure 4-15 
4.1.4 TCP/IP 
The TCP/IP interface is shown as in Figure 4-16. It supports IPv4 and IPv6. IPv4 supports static IP and 
DHCP. IPv6 supports static IP only. When users manually modify IP address, WEB will automatically 
jump to the new IP address. 
 
Figure 4-16 
Please refer to the following sheet for detailed information.