Panasonic E 37 V Dome Camera Operation Manual

                                              
 56 
 
 
Figure 4-36 
When login password keep been wrong for a few times, unauthorized access alarm occurs. This 
operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account 
will be locked.  
 
 
Figure 4-37 
4.3 Storage Management  
4.3.1 Schedule  
Before schedule setup, user must set record mode is auto or manual.  
Note: 
If record mode in record control is off, then device will not snapshot according to...

                                              
 57 
Record schedule steps: 
Step 1. Click on Record Schedule, see Figure 4-38. 
 
Figure 4-38 
Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 4-39. 
 Set period according to actual need. There are six periods available each day.  
 By checking or unchecking, you can add or delete three types of record schedule: General, Motion, 
and Alarm.  
Note: 
Period setup can be done by dragging in record schedule interface...

                                              
 58 
 Yellow color stands for the motion detect record/snapshot. 
 Red color stands for the alarm record/snapshot.  
 
Figure 4-41 
Step 4. In record schedule interface, click on OK. System prompts it is successfully saved.  
 
4.3.1.2 Snapshot Schedule 
Snapshot setup as: 
Step 1. Click on Snapshot Schedule tab, see Figure 4-42. 
Figure 4-42  

                                              
 59 
 
Step 2. From Monday to Sunday select snapshot time, click on setup on the right. See Figure 4-43 
 Set snapshot period according to actual need. There are six periods available each day.  
 By checking or unchecking, user can add or delete three types of snapshot schedule: General, 
Motion and Alarm.  
Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left 
mouse.  
 
Figure 4-43 
 
Step 3. Click on OK,...

                                              
 60 
 
Figure 4-44 
Step 5. In snapshot interface, click on OK. System prompts it is successfully saved.  
 
4.3.1.3 Holiday Schedule 
Holiday schedule can set specific date as holiday.  
Step 1. Click on Holiday Schedule tab, see Figure 4-45. 
 
 
Figure 4-45  

                                              
 61 
 
Step 2. Select date to set as holiday. The selected date will be highlighted in yellow.  
Step 3. Check Record/Snapshot, click on Save. System prompts it is successfully saved.  
Step 4. Check Record Schedule/Snapshot Schedule interface, click on setup next to Holiday, refer to 
setup of Monday to Sunday.  
Step 5. Complete setup of holiday, then it records/snapshots according to date in holiday schedule.  
 
4.3.2 Destination  
4.3.2.1 Path 
The...

                                              
 62 
Here you can view local Micro SD card or NAS disk information. You can also operate the read-only, 
write-only, hot swap and format operation.  
 
Figure 4- 47 
 
4.3.2.3 FTP 
The FTP interface is shown as in Figure 4- 48. 
You need to check the box to enable the FTP function. When network disconnect occurred or there is 
malfunction. Emergency storage can save the record/snapshot picture to the local SD card.  
 
Figure 4- 48 
 
4.3.2.4 NAS  

                                              
 63 
You need to check the box to enable the NAS function. Select NAS storage, fill in NAS server 
address and corresponding store path, then you can store video file or pictorial information in the NAS 
server.  
Select NAS storage as to same file to NAS disk. See Figure 4- 49. 
 
Figure 4- 49 
 
Parameter Function 
Server Address Set IP address of NAS server. 
Remote 
Directory 
Set storage directory, videos and pictures can be stored in to corresponding...

                                              
 64 
Parameter  Function  
Pack 
Duration 
Here you can select file size within 1min~120min. Default setup is 8 
minutes. 
Pre-record  Please input pre-record value here.  
For example, system can record the four seconds video in the buffer. 
The record begins from the fifth second.  
Note: 
Configure pre-record time, when alarm or motion detection occurs, if 
there is no record, system will record the preceding n seconds 
record.   
Disk Full There are two...

                                              
 65 
Parameter  Function  
Device 
Name 
It is to set device name.  
Note: Different devices have different names.  
Video 
Standard 
This is to display video standard such as PAL. 
 
Language  You can select the language from the dropdown list.  
 
The date and time interface is shown as in Figure 4-53. 
 
Figure 4-53 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Date format Here you can select date format from the...