Panasonic E 37 V Dome Camera Operation Manual

                                              
 26 
 
Profile management has three modes: normal, full time and schedule. If you select normal, the video will 
be configured as normal as in Figure 4-2.  
 
 
Figure 4-2 
If you select full time, you must select either day or night, and the video will be configured accordingly 
as in Figure 4-3 and Figure 4-4.  
 
Figure 4-3 
 
Figure 4-4 
  

                                              
 27 
If you select schedule, you can decide detained day time interval and night time interval as in Figure 4-
5. You can set 0:00 ~ 12:00 as day, and 12:00 ~ 24:00 as night. 
 
 
Figure 4-5 
Important 
 The setup becomes immediately effective after you click on OK. 
 You can see WDR option only if your camera supports WDR function. System does not support 
long-time exposure or low noise mode.  
4.1.2   Zoom and Focus  
Note: Only motorized vari-focal...

                                              
 28 
Parameter Function  
Zoom  
Adjust the focal length of the lens by clicking or long press “+” 
or “-“.   
Speed  can  be  used  to  adjust  the  length of  one  step  by  single 
click.  
Note:  After  adjusting  zoom,  the  device  will  focus 
automatically.  
Focus 
Adjust the lens definition by clicking or long pressing “+” “-“.  
Speed  can  be  used  to  adjust  the  length of  one  step  by  single 
click.  
Auto Focus Click to adjust the image...

                                              
 29 
 
Figure 4-7 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Sub Stream Enable  Please check the box here to enable extra stream 
function.   
This function is enabled by default.  
Code-Stream Type  ACF means using different fps to record.  
There are two options: VBR and CBR.  
Please note you can set video quality in VBR mode.  
Note:  
WEB interfaces don’t support motion detect and alarm 
code stream setting....

                                              
 30 
Parameter  Function  
Bit Rate   In CBR, the bit rate here is the max value.  In 
dynamic video, system needs to low frame rate or 
video quality to guarantee the value.  
 The value is null in VBR mode.  
 Please refer to recommend bit rate for the detailed 
information.  
I Frame  Here you can set the P frame amount between two I 
frames. The value ranges from 1 to 150.  Default value 
is 50. 
Recommended value is frame rate *2. 
Watermark Settings...

                                              
 31 
 
4.1.3.3 Video Overlay  
The video overlay interface is shown as in Figure 4- 9. 
 
Figure 4- 9 
 
Figure 4- 10  

                                              
 32 
 
Figure 4-11 
 
Figure 4-12 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Privacy mask  Here you can privacy mask the specified video in the 
monitor video.  
 System max supports 4 privacy mask zones.  

                                              
 33 
Time Title  You can enable this function so that system overlays time 
information in video window.  
 You can use the mouse to drag the time tile position.  
Channel Title   You can enable this function so that system overlays 
channel information in video window. 
 You can use the mouse to drag the channel tile position. 
Overlay  You can enable this function to display overlay picture. 
Click on disable to turn it off.  
 Click on Upload...

                                              
 34 
 
 
Figure 4-14  
 
Parameters Note  
Enable  Check “Enable”, then it will display the ROI in the video monitoring window; 
Check “Disable”, then it won’t display.                           
Image 
Quality  
 Set the image quality of ROI, ranging from 1～6, default is 6.  
Note:  
For fisheye device, it ranges from 1~6 (best), default is 6 (best) 
 Able to set area block, max 4 areas.  
 
4.1.3.5 Path  
The storage path interface is shown as below....

                                              
 35 
Note: 
Admin is locally logged in PC account.  
Please click the Save button to save current setup.  
 
Figure 4-15 
4.1.4 TCP/IP 
The TCP/IP interface is shown as in Figure 4-16. It supports IPv4 and IPv6. IPv4 supports static IP and 
DHCP. IPv6 supports static IP only. When users manually modify IP address, WEB will automatically 
jump to the new IP address. 
 
Figure 4-16 
Please refer to the following sheet for detailed information.