Panasonic E 37 V Dome Camera Operation Manual

                                              
 36 
Parameter  Function  
Host Name  It is to set current host device name. It max supports 15 
characters.   
Ethernet Card Please select the Ethernet port. Default is wired.  
Please note you can modify the default Ethernet card if there is 
more than one card. . 
Please note the device needs to reboot to activate the new 
setup once you modify the default setup.  
Mode There are two modes: static mode and the DHCP mode. Select 
DHCP mode, it auto...

                                              
 37 
Enable 
ARP/Ping set 
device IP 
address service.  
You can use ARP/Ping command to modify or set the device IP 
address if you know the device MAC address.  
Before the operation, please make sure the network camera 
and the PC in the same LAN. This function is on by default.  
You can refer to the steps listed below.  
Step 1: Get an IP address. Set the network camera and the PC 
in the same LAN. 
Step 2: Get the physical address from the label of the...

                                              
 38 
 
Figure 4-17 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Max 
connection  
It is the max Web connection for the same device. The value ranges from 1 
to 20. Default connection amount is 10. 
TCP port  Port range is 1025~65534. The default value is 37777. You can input the 
actual port number if necessary.  
UDP port  Port range is 1025~65534. The default value is 37778. You can input the 
actual port number if...

                                              
 39 
4.1.5.2 ONVIF 
ONVIF（Open Network Video Interface Forum），this standard describes network video mode, 
interface, data type and data interaction mode. ONVIF Standard’s aim is to achieve a network video 
frame agreement and makes the network video products (including video front-end, video equipment, 
etc.) from different manufacturers completely compatible.  
ONVIF function default is closed. 
 
 
Figure 4-18 
4.1.6 PPPoE 
The PPPoE interface is shown as...

                                              
 40 
 
 
Figure 4- 19 
4.1.7 DDNS 
The DDNS interface is shown as in Figure 4-20. 
The DDNS is to set to connect the various servers so that you can access the system via the server. 
Please go to the corresponding service website to apply a domain name and then access the system 
via the domain. It works even your IP address has changed. When the device connects to WLAN, you 
should disable UPnP.  
 
Figure 4-20  

                                              
 41 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Server Type You can select DDNS protocol from the dropdown list: CN99 
DDNS, NO-IP DDNS, Dyndns DDNS, QUICK DDNS, the QUICK 
DDNS function is realized according to the customized private 
protocol.  
Server Address DDNS server IP address 
CN99 DDNS 
Server address: www.3322.org 
NO-IP DDNS 
Server address: dynupdate.no-ip.com 
Dyndns DDNS 
Server address:...

                                              
 42 
 
Parameter  Function  
Server Type You can select QUICK DDNS protocol  
Server Address Under QUICK DDNS the default server address is “www.quickddns.com” 
Mode  Default is auto, manual is optional.  
Domain Name The default is “MAC address.quickddns.com” for both auto and manual, for manual 
users can set prefix by themselves.  
Test  It is to test if the domain name can be used or not. The parameter exists only when 
selecting “manual” in “Mode”....

                                              
 43 
4.1.9 SMTP （e-mail) 
The SMTP interface is shown as in Figure 4-23. 
 
Figure 4-23 
Please refer to the following sheet for detailed information. 
Parameter  Function  
SMTP Server  Input server address and then enable this function.  
Port  Default value is 25. You can modify it if necessary. 
Anonymity  For the server supports the anonymity function. You can auto 
login anonymously. You do not need to input the user name, 
password and the sender...

                                              
 44 
Parameter  Function  
Interval  The send interval ranges from 0 to 3600 seconds. 0 means 
there is no interval. 
Please note system will not send out the email immediately 
when the alarm occurs. When the alarm, motion detection or 
the abnormity event activates the email, system sends out the 
email according to the interval you specified here. This 
function is very useful when there are too many emails 
activated by the abnormity events, which may...

                                              
 45 
 
Figure 4-24 
 
4.1.11 Bonjour 
The Bonjour interface is shown as below. See Figure 4-25. 
Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically 
broadcast its service information and listen to the service information from other device. 
You can use the browse of the Bonjour service in the same LAN to search the network camera device 
and then access if you do not know the network camera information such as...