Panasonic Dx2000 Users Guide

49
To Retrieve the Internet Parameters for Backup
To retrieve the existing Internet Parameters, send a plain text email to the DX-2000’s email address with the
following command in the Subject line:
#get parameters(password)#
 : where the password is the Remote Password programmed in the DX-2000’s
User Parameters (i.e. 123456789).  For security, always input a Remote
Password in the User Parameters.  If it was not programmed, signify with () (i.e.
#get parameters()#).
Make sure that the CC..., Bcc......

50
After receiving the email message requesting the Internet Parameters, the DX-2000 sends back an email to the
address specified in theFrom: line with the Internet Parameters in the body of the email.
DX-2000 Internet Parameters Email Sample
(1) To : Your email address (email application) that was used to retrieve the Internet Parameters.
From : The DX-2000’s email address.
Subject : DX-2000 System Parameter List
(2) @sender to @end : Defines up to 24 User Names and their Email Addresses programmed in...

51
To Edit the Retrieved or Backup Internet Parameters File
After receiving the DX-2000 email with the Internet Parameters, store the email file as text (.txt) on your PC for
backup purposes.
To change or update the Internet Parameters, follow the steps below:
1. Create a New Email Message, fill out the To and From Address line and the Subject line information for
section 1) below: 
To : The DX-2000’s email address.
From : This field is normally not visible when creating new email message(s).  It is your...

52
DX-2000 Internet Parameters Email Sample
(1)
(2)
(3)
(4)
(5)
[Delete this header before sending email.] 
Programming or Retrieving Parameters via Email 

53
(1) To : The DX-2000’s email address
From : This field is normally not visible when creating new email message(s).  It is your default
email address (email application), for retrieving the Internet Parameters and for error
message notification.
(Can be programmed with the configuration tool of your email program.)
Subject : To Store data, type: #set parameters(password)#
(2) @sender to @end : Defines the Sender information to be set in section (2) between @sender to @end block.
Edit, Delete or...

54
Using a PC to Update the Auto Dialer Remotely
This feature provides a convenient and an easy way to Update, Backup or Restore the One-Touch and
Abbreviated dialing numbers right from your PC by sending a text email message to the DX-2000.
The DX-2000 interprets the command that you enter in the Subject line of your email message and performs
one of the following functions, it Retrieves or Stores data into the Auto Dialer (One-Touch and/or ABBR No.).
The two types of commands that can be entered in the...

55
Deleting the Entire Auto Dialer
If you wish to delete the entire Auto Dialer data in the DX-2000, type the following command in the body of the
email message:
    
@command
delete
@end
This command can also be inser ted before the @begin to @end block, to erase the entire Auto Dialer data first,
then reprogramming it with new data.  
This method will also prevent the Overwrite Warning Message that is sent back from the DX-2000, when the
current Auto Dialer station is overwritten.
To erase the entire...

56
To Program One-Touch / ABBR No. for the First Time
Create a script in the message body of a plain text email and send it to the DX-2000’s email address.The
Subject line of the email must be as follows:  
#set abbr(password)#:
where the password is the Remote Password programmed in the DX-2000’s User 
Parameters.
The script sample to program One-Touch / ABBR No. for the first time is shown in the illustration below:
First Time Remote Programming of One-Touch / ABBR No. Sample
(1)
(2)
(3) (b)
(c)...

57
 (see Note 1)  (see Note 2)  (see Note 3)  (see Note 4)
(1) To : The DX-2000’s email address.
From : This field is normally not visible when creating new email message(s).  It is your default email address 
(email application), for retrieving the One-Touch / ABBR No. data and for error message notification.
(It can be programmed with the configuration tool of your email program)
Subject : To Store data, type: #set abbr(password)# 
: To Retrieve data, type: #get abbr(password)#
(2) @begin to @end block...

58
To Retrieve One-Touch / ABBR No. Data for Backup
To retrieve the existing auto dialer data, send a plain text email to the DX-2000’s email address with the following
command in the Subject line:
#get abbr(password)#
: where the password is the Remote Password programmed in the DX-2000’s User
Parameters  (i.e. 123456789)
Make sure that the CC, Bcc lines and the body of the email message is Blank.
Retrieving One-Touch / ABBR No. Data Sample
To : The DX-2000’s email address.
From : This field is normally...