Panasonic DLP Projector PT-DZ780 PT-DW750 PT-DX820 Operating Instructions

							Chapter 4 Settings — Menu navigation
ENGLISH - 71
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as to select an item from the main menu.
 fThe selected item is highlighted in yellow

.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
3) Press the  button.
 fThe sub-menu items of the selected main menu are displayed.
0
POSITION
SHIFT
ASPECT
ZOOM
GEOMETRY CLOCK PHASE
MENU SELECT
SUB MENU DEFAULT
ENTER
OFF   
						

							Chapter 4 Settings — Menu navigation
72 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown be\
low.
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu. fDepending on the signals to be input to the projector
, some items or functions may not be adjusted or used. If items or funct\
ions cannot be 
adjusted or used, the items on the menu screen are shown in black characters, and they cannot be selected. [DIGIT AL CINEMA REALITY] 
may not be displayed depending on the input signals.
 f Some items can be adjusted even if signals are not input. fIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. fFor menu items, refer to “Main menu” (

x   page   72) and “Sub-menu” (x
  page   73).
 fThe cursor color depends on the settings of the [DISPLA

Y OPTION] menu → [ON-SCREEN DISPLAY] → [OSD DESIGN]. The selected 
item is displayed with the yellow cursor by the factory default.
Resetting adjustment values to the factory default
If the  button on the remote control is pressed, the values adjusted in the menu items are restored to 
the factory default settings.
 button
1) Press the  button on the remote control.
0CONTRAST
ADJUST
Note
 fYou cannot reset all the settings to the factory default at a time. fT
o reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECT OR SETUP] menu → 
[INITIALIZE] ( x
  page   126).
 fSome items cannot be reset to the factory default settings even when the  button on the remote control is pressed. Adjust those 
items individually.
 f The triangular mark 

under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular 
mark varies according to the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu sele\
ction screen.
Main menu item Page
[PICTURE] 76
[POSITION]83
[ADVANCED MENU]88
[DISPLAY LANGUAGE]93
[DISPLAY OPTION]94   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 73
Main menu itemPage
[PROJECTOR SETUP] 111
[P IN P]128
[TEST PATTERN]130
[SIGNAL LIST]131
[SECURITY]134
[NETWORK]138
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can se\
t and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE] [STANDARD]
*176
[CONTRAST] [0]76
[BRIGHTNESS] [0]76
[COLOR] [0]77
[TINT] [0]77
[COLOR TEMPERATURE] [DEFAULT]77
[WHITE GAIN] [+10]79
[GAMMA] [DEFAULT]79
[SYSTEM DAYLIGHT VIEW] [OFF]80
[SHARPNESS] [+6]80
[NOISE REDUCTION] [OFF]80
[AI] [ON]81
[SYSTEM SELECTOR] [YP
BPR]*181
*1 Depends on the signal input.
Note
 fThe factory default settings may vary depending on the picture mode.
[POSITION] 
Sub-menu item Factory defaultPage
[SHIFT] ―83
[ASPECT] [DEFAULT]
*183
[ZOOM] ―84
[CLOCK PHASE] [0]
*185
[GEOMETRY] [OFF]85
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub-menu item Factory defaultPage
[DIGITAL CINEMA REALITY] [AUTO]
*188
[BLANKING] ―88
[INPUT RESOLUTION] ―89
[CLAMP POSITION] [24]
*189
[EDGE BLENDING] [OFF]90   
						

							Chapter 4 Settings — Menu navigation
74 - ENGLISH
Sub-menu itemFactory defaultPage
[FRAME RESPONSE] [NORMAL]91
[RASTER POSITION] ―92
*1 Depends on the signal input.
Note
 fSub-menu items and factory default settings vary depending on the selected input terminal.
[DISPLAY LANGUAGE] 
Details (x page 93)
[DISPLAY OPTION] 
Sub-menu item Factory defaultPage
[COLOR MATCHING] [OFF]94
[COLOR CORRECTION] [OFF]95
[SCREEN SETTING] ―95
[AUTO SIGNAL] [OFF]96
[AUTO SETUP] ―96
[BACKUP INPUT SETTING] ―97
[RGB IN] ―98
[DVI-D IN] ―99
[HDMI IN] ―101
[DIGITAL LINK IN] ―102
[SDI IN]
*1― 103
[ON-SCREEN DISPLAY] ―104
[CLOSED CAPTION SETTING] ―106
[BACK COLOR] [BLUE]106
[STARTUP LOGO] [DEFAULT LOGO]107
[UNIFORMITY] ―107
[SHUTTER SETTING] ―108
[FREEZE] ―108
[WAVEFORM MONITOR] [OFF]108
[CUT OFF] ―11 0
*1 Only for PT-DZ780
[PROJECTOR SETUP] 
Sub-menu item Factory defaultPage
[PROJECTOR ID] [ALL]111
[PROJECTION METHOD] [FRONT/FLOOR]111
[COOLING CONDITION] [AUTO]11 2
[LAMP SELECT] [DUAL]11 2
[LAMP RELAY] [OFF]11 3
[LAMP POWER] [NORMAL]11 3
[BRIGHTNESS CONTROL] ―11 4
[STANDBY MODE] [NORMAL]11 8
[SCHEDULE] [OFF]11 9
[INITIAL STARTUP] [LAST MEMORY]120
[STARTUP INPUT SELECT] [LAST USED]120
[RS-232C] ―121
[STATUS] ―122
[NO SIGNAL SHUT-OFF] [DISABLE]124
[REMOTE2 MODE] [DEFAULT]124
[FUNCTION BUTTON] ―124   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 75
Sub-menu itemFactory defaultPage
[DATE AND TIME] ―124
[LENS CALIBRATION] [NORMAL]125
[SAVE ALL USER DATA] ―126
[LOAD ALL USER DATA] ―126
[INITIALIZE] ―126
[SERVICE PASSWORD] ―127
[P IN P] 
Details (x page 128)
[TEST PATTERN] 
Details (x page 130)
[SIGNAL LIST] 
Details (x page 131)
[SECURITY] 
Sub-menu item Factory defaultPage
[SECURITY PASSWORD] [OFF]134
[SECURITY PASSWORD CHANGE] ―134
[DISPLAY SETTING] [OFF]134
[TEXT CHANGE] ―135
[CONTROL DEVICE SETUP] ―135
[CONTROL DEVICE PASSWORD CHANGE] ―136
[NETWORK] 
Sub-menu item Factory defaultPage
[DIGITAL LINK MODE] [AUTO]138
[DIGITAL LINK SETUP] ―138
[DIGITAL LINK STATUS] ―139
[NETWORK SETUP] ―139
[NETWORK CONTROL] ―140
[NETWORK STATUS] ―140
[DIGITAL LINK MENU] ―141
[Art-Net SETUP] [OFF]141
Note
 fSome items may not be adjusted or used for certain signal formats to be input to the projector .
The menu items that cannot be adjusted or used are shown in black charac\
ters, and they cannot be selected.
 f Sub-menu items and factory default settings vary depending on the selected input terminal.   
						

							Chapter 4 Settings — [PICTURE] menu
76 - ENGLISH
[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   71) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to adjust.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the 
projector is used.
1)
 
Press 
 as to select [PICTURE MODE].
2)
 
Press 
 qw or the  button.
 fThe 

[PICTURE MODE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[STANDARD] The image becomes suitable for moving images in general.
[CINEMA] The image becomes suitable for movie contents.
[NATURAL] The image becomes sRGB compliant.
[REC709]
*1The image becomes Rec.709 compliant.
[DICOM SIM.] The image becomes similar to that of DICOM Part14 gray scale standard.
[DYNAMIC] The image becomes suitable for use in bright areas.
[GRAPHIC] The image becomes suitable for input from the personal computer.
*1 Use the factory default settings other than for [PICTURE MODE].
Note
 fThe factory default picture mode is [GRAPHIC] for still image input signals and [ST ANDARD] for movie-based input signals. fRec.709 is an abbreviation of “ITU-R Recommendation BT
.709” and is a color standard of high-vision broadcasting.
 fDICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices.  Although the 
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
[CONTRAST]
You can adjust the contrast of the colors.
1)
 
Press 
 as to select [CONTRAST].
2)
 
Press 
 qw or the  button.
 fThe 

[CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. The screen becomes brighter.
-31 - +31
Press q. The screen becomes darker.
Attention
 f
Adjust [BRIGHTNESS] first when you need to adjust the black level.
[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1)
 
Press 
 as to select [BRIGHTNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[BRIGHTNESS] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 77
OperationAdjustmentRange of adjustment
Press w. Increases the brightness of the dark (black) parts of the screen.
-31 - +31
Press q. Reduces the brightness of the dark (black) parts of the screen.
[COLOR]
You can adjust the color saturation of the projected image.
1)
 
Press 
 as to select [COLOR].
2)
 
Press 
 qw or the  button.
 fThe 

[COLOR] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Deepens colors.
-31 - +31
Press q. Weakens colors.
[TINT]
You can adjust the skin tone in the projected image.
1)
 
Press 
 as to select [TINT].
2)
 
Press 
 qw or the  button.
 fThe 

[TINT] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Adjusts skin tone toward greenish color.
-31 - +31
Press q. Adjusts skin tone toward reddish purple.
[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
Adjusting with color temperature
1) Press 
as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[USER1] Adjusts white balance as desired. Refer to “Adjusting desired white balance” ( x
  page   77) for 
details.
[USER2]
[3200K] - [9300K] Allows you to set in increments of 100
  K. Select so that images become natural.
Note
 fWhen [PICTURE MODE] ( x   page   76) is set to [DICOM SIM.], [DEFAULT] cannot be selected. fWhen [COLOR MA
TCHING] (x   page   94) adjustment is set to other than [OFF], [COLOR TEMPERATURE] is fixed to [USER1].
 fThe color temperature numerical values are guidelines.
Adjusting desired white balance
1) Press  as to select [COLOR TEMPERATURE].   
						

							Chapter 4 Settings — [PICTURE] menu
78 - ENGLISH
2) Press qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER1] or [USER2].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.
5)
 
Press 
 as to select [WHITE BALANCE].
6)
 
Press the  button.
 fThe 

[WHITE BALANCE] screen is displayed.
7)
 
Press 
 as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].
8)
 
Press the  button.
 fThe 

[WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.
9)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
10)
 
Press 
 qw to adjust the level.
Item Operation Adjustment Range of adjustment
[RED] Press w.
Deepens red.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is +255)
[WHITE BALANCE LOW]: 
-127 - +127 (factory default is 
0)
Press q.
Weakens red.
[GREEN] Press w.
Deepens green.
Press q. Weakens green.
[BLUE] Press w.
Deepens blue.
Press q. Weakens blue.
Note
 f
Adjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
Adjusting desired white balance based on existing color temperature sett\
ings
1) Press  as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select an item other than [DEFAULT], [USER1], and [USER2].
4)
 
Press the  button.
 fThe 

[CHANGE TO *****] screen is displayed.
5)
 
Press 
 as to select [USER1] or [USER2].
 fThe status of the color temperature changed is saved to the selected ite\
m.
6)

 
Press the  button.
 fThe confirmation screen is displayed.
7)

 
Press 
 qw to select [OK], and press the  button.
 fThe [USER1] or [USER2] data is overwritten.
 fIf you press 

qw to select [CANCEL] and then press the  button, the data will not be overwritten.
 fThe 

[WHITE BALANCE HIGH] screen is displayed.
8)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
9)
 
Press 
 qw to adjust the level.   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 79
Note
 fAdjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
 f When color temperature has been changed, the colors before and after the\
 change will dif

fer slightly.
Changing the name of [USER1] or [USER2]
1) Press as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER1] or [USER2].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.
5)
 
Press 
 as to select [COLOR TEMPERATURE NAME CHANGE].
6)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE NAME CHANGE] screen is displayed.
7)
 
Press 
 asqw to select the text, and press the  button to enter the text.
8)
 
Press 
 asqw to select [OK], and press the  button.
 fThe name set to color temperature is changed.
Note
 f When a name is changed, display of [USER1], [USER2] is also changed.
[WHITE GAIN]
Adjust the brightness of the white part of the image.
1)
 
Press 
 as to select [WHITE GAIN].
2)
 
Press 
 qw or the  button.
 fThe 

[WHITE GAIN]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Brightness of the white part gets stronger.
0 - +10
Press q. The image becomes more natural.
[GAMMA]
You can switch gamma mode.
1)
 
Press 
 as to select [GAMMA].
2)
 
Press 
 qw or the  button.
 fThe 

[GAMMA] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[1.8] Set an item so that images become as you like.
[2.0]
[2.2]   
						

							Chapter 4 Settings — [PICTURE] menu
80 - ENGLISH
Note
 fWhen the edge blending adjustment is performed while [DEF AULT] is selected, it will be the same gamma mode as when [2.2] is selected. 
(Only for PT- DW750 and PT- DX820)
[SYSTEM DAYLIGHT VIEW]
You can correct the image to the optimal vividness even if it is projected under a bright light.
1)
 
Press 
 as to select [SYSTEM DAYLIGHT VIEW].
2)
 
Press 
 qw or the  button.
 fThe 

[SYSTEM DAYLIGHT VIEW]  individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Corrects the image to weaken vividness.
[2] Corrects the image to medium vividness.
[3] Corrects the image to high vividness.
[SHARPNESS]
You can adjust the sharpness of the projected image.
1)
 
Press 
 as to select [SHARPNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[SHARPNESS]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Contours become sharper.
0 - +15
Press q. Contours become softer.
Note
 f
If you press  w while the adjustment value is [+15], the value will become [0]. If you press  q while the adjustment value is [0], the value will 
become [+15].
[NOISE REDUCTION]
You can reduce noises when the input image is degraded and noise is occurring in the image signal.
1)
 
Press 
 as to select [NOISE REDUCTION].
2)
 
Press 
 qw or the  button.
 fThe 

[NOISE REDUCTION] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Slightly corrects the noise.
[2] Moderately corrects the noise.
[3] Strongly corrects the noise.
Attention
 fWhen this is set for an input signal with less noise, the image may look dif ferent from what it originally was. In such a case, set it to [OFF].