Panasonic DLP Projector PT-DW640U PT-DW640UL PT-DX610U PT-DX610UL Operating Instructions

ENGLISH - 71
Chapter 4 Settings — [DISPLAY OPTION] menu
6) Press qw to switch [DVI SIGNAL LEVEL].
r
f The setting will change between [0-255:PC] and [16-235] each 
time you press the button.
r
r [DVI EDID]
[EDID3]
Switch between fine settings for a moving image and for a still image.
[EDID1] Select mainly when an external device that outputs movie-type image signals (such as a blu-ray disk 
player) is connected to the  terminal.
[EDID2:PC] Select mainly when an external device that outputs still...

72 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
r
r [ON-SCREEN DISPLAY]
[OSD POSITION] [2]
Set the position of the menu screen (OSD) to the center left of the screen.
[3] Set the position of the menu screen (OSD) to the bottom left of the screen.
[4] Set the position of the menu screen (OSD) to the top center of the screen.
[5] Set the position of the menu screen (OSD) to the center of the screen.
[6] Set the position of the menu screen (OSD) to the bottom center of the screen.
[7] Set the...

ENGLISH - 73
Chapter 4 Settings — [DISPLAY OPTION] menu
Note
r
f The startup logo will disappear in approximately 15 seconds.
r
f To create the image for [USER LOGO], “Logo Transfer Software” included in the supplied CD-ROM is required.
[SHUTTER SETTING]
Set the opening and closing status of the shutter for when projection begins by switching on the projector
, and for when the projector is 
switched off.
To set [STARTUP]
1) Press as to select [SHUTTER SETTING].
2) Press the  button.
r
f The 
[SHUTTER...

74 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
r
r Setting the two window display
[VIDEO]
Displays images of [VIDEO] input on the right screen (Input B).
[S-VIDEO] Displays images of [S-VIDEO] input on the right screen (Input B).
[RGB1] Displays images of [RGB1] input on the right screen (Input B).
[RGB2] Displays images of [RGB2] input on the right screen (Input B).
[DVI-D] Displays images of [DVI-D] input on the right screen (Input B).
[HDMI] Displays images of [HDMI] input on the right screen...

ENGLISH - 75
Chapter 4 Settings — [PROJECTOR SETUP] menu
[PROJECTOR SETUP] menu
Select [PROJECTOR SETUP] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (
x page 51) for the operation of the menu screen.
r
f After selecting the item, press 
asqw to set.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when multiple projectors are used side by side to enable simultaneous 
control or individual control via one remote control....

76 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
[COOLING CONDITION]
Change the fan control depending on the direction of projection.
Set [COOLING CONDITION] correctly in accordance with the direction of projection referring to the following figure. It may shorten the life of 
the lamp if used in incorrect setting.

30°
30° 30°
30°
[
VER
TICAL  UP SETTING]
[FLOOR SETTING] [CEILING SETTING]
[VERTICAL  DOWN SETTIN G]
Projection direction
1) Press as to select [COOLING CONDITION].
2) Press the...

ENGLISH - 77
Chapter 4 Settings — [PROJECTOR SETUP] menu
operating time of either of them exceeds 2 500 hours (when [LAMP  POWER] is set to [NORMAL]), only the other lamp will light. However , if 
both lamps do not light, or the cumulative operating time of both of them exceeds 2 500 hours (when [LAMP  POWER] is set to [NORMAL]), 
the projector will go into standby.
r
f The font colors of the items indicate the status.
Green 
→ Current setting
Yellow  → Current setting (when there is a lamp that cannot...

78 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
[ECO] Set when high luminance is not required.
Note
r
f When [ECO] is set, the power consumption and operation sound can be reduced while the lamp life can be increased.
[STANDBY MODE]
Set the power consumption during the standby.
1) Press as to select [STANDBY MODE].2) Press qw to switch [STANDBY MODE].
r
f The setting will change between [NORMAL] and [ECO] each 
time you press the button.
r
r [STANDBY MODE]
[NORMAL]
Normally use this setting....

ENGLISH - 79
Chapter 4 Settings — [PROJECTOR SETUP] menu
7) Press qw to select hour and minute, and press 
as or the number ( to ) buttons to set 
a time, and press the  button.
8) Press as to select [COMMAND].
9) Press qw to switch [COMMAND].
r
f The setting will change among [POWER ON], [STANDBY], 
[SHUTTER]*1, [INPUT]*1, [LAMP SELECT]*1, [LAMP POWER]*1 
and [SIDE BY SIDE]*1*2 each time you press the button.
*1  The details set in step  11 ) are displayed.
*2  Only for PT-DW640U
10) Press the  button....

80 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
[S-VIDEO] Sets the input to be projected when the projector is switched on to S-VIDEO.
[DVI-D] Sets the input to be projected when the projector is switched on to DVI-D.
[HDMI] Sets the input to be projected when the projector is switched on to HDMI.
[RS-232C]
Set the communication conditions of the / terminal.
To set the communication condition of the  terminal
1) Press as to select [RS-232C].
2) Press the  button.
r
f The 
[RS-232C]  screen is...