Panasonic DLP Projector PT-DW640U PT-DW640UL PT-DX610U PT-DX610UL Operating Instructions

ENGLISH - 101
Chapter 4 Settings — [NETWORK] menu
[E-mail set up] page
You can send E-mail to an E-mail address (maximum two addresses) set in advance when a problem occurs or the cumulative operating time 
of a lamp reaches a set value.
Click [Detailed set up]
 → [E-mail set up].
(1)
(2)
(3)
(4)
(5)
(6)
1 
[ENABLE]
Select [Enable] to use the E-mail function.
2  [SMTP SERVER NAME]
Enter the IP address or the server name of the E-mail server 
(SMTP). To enter the server name, the setup of the DNS server...

102 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
(11)
(10)
(9)
9 [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent when two E-mail addresses 
are to be used.
Leave it blank when two E-mail addresses are not to be used.
10  Settings of the conditions to send E-mail
Select the conditions to send E-mail to the second E-mail 
address.
[MAIL CONTENTS]:
Select either [NORMAL] or [SIMPLE].
[ERROR]:
An E-mail message is sent when an error occurred in the self-
diagnosis.
[LAMP1 RUNTIME]:
An E-mail message...

ENGLISH - 103
Chapter 4 Settings — [NETWORK] menu
Contents of mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : DW640
Serial No               : SH1234567
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP 
MINIMUM TIME           at [ 60] minutes interval 
INTAKE AIR TEMPERATURE Over [ 45 degC / 113 degF ] 
ERROR                   [ OFF ] 
LAMP1...

104 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : DW640
Serial No               : SH1234567
-----  check system -----
MAIN CPU BUS   [   OK   ]
FAN   [   OK   ]
INTAKE AIR TEMPERATURE   [   OK   ]
OPTICS MODULE TEMPERATURE   [   OK   ]
AROUND LAMP TEMPERATURE   [   OK   ]
LAMP1 REMAIN TIME   [   OK   ]
LAMP2 REMAIN TIME   [   OK   ]
LAMP1...

ENGLISH - 105
Chapter 4 Settings — [NETWORK] menu
[Administrator] account
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1 [Account]
Displays the account to change.
2  [Current][User name]
Enter the user name before the change.
3  [Current][Password]
Enter the current password.
4  [New][User name]
Enter the desired new user name. (Up to 16 characters in single 
byte) 5 
[New][Password]
Enter the desired new password. (Up to 16 characters in single 
byte)
6  [New][Password(Retype)]
Enter the desired new password again.
7...

106 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
[Change password] (For user rights)
Only the change of password is enabled under the user rights.
(1)
(2)
(4) (3)
1 [Old Password]
Enter the current password.
2  [New Password]
Enter the desired new password. (Up to 16 characters in single 
byte) 3 
[Retype]
Enter the desired new password again.
4  [OK]
Determines the change of password.
Note
r
f To change the account of the administrator, you must enter the [Current] [User name] and [Password].
[CRESTRON...

ENGLISH - 107
Chapter 4 Settings — [NETWORK] menu
[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector.
2  [User Password]
Set the user rights password for the RoomView control page.
3  [Admin Password]
Set the administrator rights password for the RoomView control 
page.
4  Network Status
Displays the settings of wired LAN. [DHCP]
Displays the current setting.
[Ip Address]...

108 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]
Messages can be sent to or received from an administrator who 
uses Crestron RoomView.  

ENGLISH - 109
Chapter 5 Maintenance
This chapter describes inspection when there are problems, and maintenance methods.  

110 - ENGLISH
Chapter 5 Maintenance — Lamp/Temperature/Filter indicators
Lamp/Temperature/Filter indicators
Managing the indicated problems
If a problem should occur inside the projector, the lamp indicators // the temperature indicator  and the filter 
indicator  will inform you by lighting or flashing.
Check the status of the indicators and manage the indicated problems as follows.
Attention
r
f When switching off the projector to deal with problems, make sure to follow the procedure in “Switching off...