Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

1
2
3
4
5
6
7
8
9
10
11
12
1-7
Clearing the Functions Selected
The icons displayed on the screen are as follows (some icons may not appear on the screen):
If you press any key that is half-tone shaded, the function selected is cleared. Also, if the machine is left
inactive for approx. 45 seconds, the automatic function clear (
 Page 1-4) works and the settings will be
cleared.
-SETTINGS  (set functions confirmation) key
This key allows you to confirm the functions that have been
set. (The display shown...

1
2
3
4
5
6
7
8
9
10
11
12
1-8BEFORE MAKING COPIES
While the above message is displayed, stopping printing due to
paper jam, etc. Cancels the job of auto start. To clear this status,
press the  
 FUNCTION CLEAR  or the     STOP  key.
2. TURNING  ON THE  POWER  SWITCH
Turning ON the Power Switch/Auto Job Start
2
When “READY” appears, the machine is ready for
copying.
1
Turn ON the power switch.
- This message appears on the message panel of the Basic
Screen:
Wait Warming Up
Up to 5 jobs can be stored in...

1
2
3
4
5
6
7
8
9
10
11
12
1-9
Controlling the Use of the Machine with Department Codes
1
When the department code function is in use, the
screen shown on the right appears immediately
after the power switch is turned on or the auto-clear
is carried out.
2
Key in a registered department code (5-digit).
- The machine will be ready for copying.
With the use of department codes, you can restrict machine users as well as manage copy volumes
made by individual groups or departments of your company.
*...

1
2
3
4
5
6
7
8
9
10
11
12
2-1
2. HOW TO MAKE COPIES
1. GENERAL COPYING PROCEDURES .................................... 2-2
2. SETTING COPY PAPER .......................................................... 2-4
- Acceptable Copy Paper Types and Sizes ................................................... 2-4
- Handling and Storing Paper ....................................................................... 2-5
- Changing the Paper Size of the Drawer/
Setting the Drawer for Special Uses ............... 2-6
3....

12
3
4
5
6
78
9
10
11
12
2-2HOW TO MAKE COPIES
Initial (default) settings
1. GENERAL COPYING PROCEDURES
After placing, or confirming that there is, paper in the drawers, place the originals. When the   START
key is pressed with any settings unchanged, copies are made in the initial\
 (default) settings *1. You  can
make copies as desired by setting different copy modes.
The initial (default) settings of the machine at the time of installation are as shown below.
*1 The copy modes that are automatically...

1
2
3
4
5
6
7
8
9
10
11
12
2-3
  - After starting copying, press the  JOB STATUS  key on the control panel, then press the
 STATUS  key on the touch panel to indicate which drawer is in use. When paper runs out
of each drawer, the empty drawer will flash.
6
Once the final original has been scanned, press the  FINISHED  key.
- When the reversing automatic document feeder is used, and the single-feed mode is selected,
the procedure is slightly different from the above. Procedure of using the single-feed...

1
2
3
4
5
6
7
8
9
10
11
12
2-4HOW TO MAKE COPIES
Feeder
Drawers
Tandem LCF
External LCF
(optional)
Sheet Bypass
Paper Type
Plain Paper
(17- 20 lb Bond)
Thick 1
( - 90 lb Index)
Thick 2
( -110 lb Index)
Tab paper
Plain Paper
(17 - 20 lb Bond)
Thick 1
(-90 lb Index)
Thick 2
(-110 lb Index)
Plain Paper
(17 - 20 lb Bond)
Thick 1
(-90 lb Index)
Thick 2
(-110 lb Index)
Plain Paper
(17- 20 lb Bond)
Thick 1
(-90 lb Index)
Thick 2
(-110 lb Index)
Tracing Paper
Tab paper
OHP film
2. SETTING COPY PAPER
Acceptable...

1
2
3
4
5
6
7
8
9
10
11
12
2-5
Pay attention to the following points:
- Avoid using paper that is specially treated or paper that was printed on another machine, and also
avoid performing double copying on the same side of paper; this may cause a malfunction.
- Do not use paper with creases, wrinkles, curled paper, paper prone to curling, smooth paper, or
tough paper; this may cause paper misfeeds.
- Paper should be wrapped in its wrapping paper and stored in a damp-free place.
- To prevent paper from...

1
2
3
4
5
6
7
8
9
10
11
12
2-6HOW TO MAKE COPIES
Slide rail
2. SETTING COPY PAPER (Cont.)
Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses
The paper size of the drawers of the machine can be changed to desired size. The drawers can also be
set for cover sheet, insertion, tab paper, thick paper and special sheets.
4
While pushing the size selection lever in the direction of
the arrow, set the side guide to the desired paper
width.
- Adjust the side guides with both hands.
3
Push...