Panasonic Digital Disk Recorders Wj Hd309a Operating Instructions

							91
 Alarm connection
When a signal is supplied to the alarm input terminals of CH 1-16, recording and displaying of camera images will be per-
formed according to the settings.
When an alarm device such as a buzzer, a lamp, etc., is installed outside, connect them to the alarm output terminals (pin nos.
9 - 12, pin nos. 23 - 25) or to the alarm output terminals (pin nos. 1 - 9) of the ALARM/CONTROL terminal.
Alarming devices
Relay, etc.
Alarming devices
Install according to
your needs.Relay, etc.
(GND)
Sensor 
Security door 
switch
(Ch 16 alarm input)
(Ch 1 alarm input)
o !3
!3o!4
@2q
(Ch 1 alarm output)
(Ch 16 alarm output)(Earth)
(Earth)
Install according to
your needs.ALARM
ALARM/CONTROL
Time and polarities of the ALARM/CONTROL terminal and the ALARM terminal
Terminal
Alarm input
Alarm output
Alarm reset input
Emergency recording input
Alarm output for available disk space of
device connected to the copy port
HDD error output
Camera error output
Error output
Outage processing end output
Time adjust I/O
Sequence changeover output
Outage detection output
External recording mode changeover
Alarm suspend outputActive time
100 ms or more
The set time on the SETUP MENU
100 ms or more
100 ms or more
While the size of the available disk
space is less than the set size
Until the HDD error is cleared
Until the camera error is cleared
Until the error is cleared
100 ms
Input: 100 ms or more
Output: 1 s
100 ms or more
100 ms or more
100 ms or more
100 ms or moreNote
N.O.: L active
N.C.: H active
L active
L active
L active
L active
L active
L active
L active
H active
L active
L active
L active
L active, judged by level
L active, judged by level 
						

							92
How to Use the SERIAL Connector
This connector is compliant with the RS232C Standard, and is used to communicate with a connected PC.
A connection example and the pin configuration of the SERIAL connector are as shown below.
Important:
When using the SERIAL connector, it is necessary to perform the settings with RS232C Setup of Comm on the SETUP
MENU for the communication functions. (Page 132)
Pin Configuration
Connection example
1 18
2
IN
OUTCASCADE
OUT
16 16 315 1514
1413
2 113
12 1211
1110
109
98
87
76
65
54
43
32
21
1VIDEO
AUDIO IN AUDIO OUTMONITOR OUT CASCADE INMONITOR (VGA) ALARM/CONTROLSERIAL ALARMPOWER COPY 1 MODEEXT STORAGE 10/100BASE-T RS485(CAMERA)D ATAAC  IN
SIGNAL GND1
42
D-sub Pin 9
(Female)D-sub Pin 9
(Female)
This unitPC
(Locally procured)
Serial connector of this unit
D-sub Pin 9 (Female)Personal computer side
D-sub Pin 9 (Female)
Connection example of cross cable
7 (RTS)
8 (CTS)
3 (TXD)
5 (GND)
2 (RXD)7 (RTS)
8 (CTS)
3 (TXD)
5 (GND)
2 (RXD)
WJ-HD316A/WJ-HD309A
PC or another device 
						

							93
SETUP
To operate this unit, it is necessary to set each item of the SETUP MENU in advance.
Using the SETUP MENU (Quick) and the SETUP MENU (Advanced)
First, check the setting items of the SETUP MENU (Quick) and perform the settings. When more detailed settings are required,
perform the settings on the SETUP MENU (Advanced).
Refer to page 101 for descriptions about the SETUP MENU (Advanced).
Perform the settings for each item of the SETUP MENU by displaying the SETUP MENU on monitor 2.
Settings items are as below.
About the SETUP MENU (Quick)
Menu:These menus are always displayed on the SETUP MENU (Quick).
Live image:Live images from the camera channel that was selected just before the SETUP MENU (Quick) was displayed, will
be displayed in this area.
Main area:The setting items of the selected menu will be displayed in this area.
Item list of the SETUP MENU (Quick)
Display Perform the display settings such as the display position of the camera title and
time, and the settings for other basic operations of this unit.
REC & Event Perform the basic settings for recording and alarm operation.
Network Perform the basic network settings.
SETUP MENULIVEQuick
Display
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence
 Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
Menu
Main area
Live image
Settings menu Description Page
94
97
100 
						

							94
[Display]
Perform the time and date, display settings such as the
time and date display, the camera title display, the sequen-
tial display and the language setting.
8Date Format
Select a display format for the date from the following. (Ex.
April 1, 2004)
YY.MM.DD:04.4.1
MMM.DD.YY:APR.1.04
DD.MMM.YY:1.APR.04
8Time Format
Select a display format for the time from the following. (Ex.
3 o’ clock in the afternoon)
12h:3:00:00 PM
24h:15:00:00
8Time & Date
Adjust the current time and date.
Enter year, month, day, hour, minute and second in order,
move the cursor to SET and press the SET button.
Important:
Recording will stop for around 4 seconds just after set-
ting the date and time.
8Time & Date Display Position
Select a time and date display position from the following.
L-UPPER:Displays the time at the upper left of the screen.
R-UPPER:Displays the time at the upper right of the
screen.
L-LOWER:Displays the time at the lower left of the screen.
R-LOWER:Displays the time at the lower right of the
screen.
Notes:
•When setting the time and date to be recorded together
with images, the time display will be recorded in the
selected position.
•Refer to page 111 for further information about
Embedded REC (Time & Date).
8Camera Title
Perform the settings for the camera title. It is possible to
display a camera title on the monitor 1/monitor 2, and
record it as a part of the recorded image (page 111). Do
the following to set the camera title.[Screenshot 1]
Start operation from the Display menu.
zMove the cursor to Camera Title using the arrows but-
ton (CD) and press the SET button.
[Screenshot 2]
The Camera Title pop-up window will be displayed.
xMove the cursor to CAM1 using the arrows button.
[Screenshot 3]
The cursor moves to CAM1.
cSelect a character to be entered by rotating the jog dial.
Up to 16 characters can be entered.
vMove the cursor to the right side of the entered charac-
ter using the arrows button (B). 
Repeat steps 3 and 4 to enter the camera title.
The available characters for a camera title are different
depending on the selected language as follows.

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q
R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u
v w x y z À Ä Â Æ Ç É Ì Ñ Ò Ö Ù Ü Ø ß à á â ä å æ ç è
é ê ë ì í î ï ñ ò ó ô ö ù ú û ü ø ?  # & ( ) * + , - . / : ; SP
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
CAM1Camera Title1CAM2 2CAM3 3CAM4 4CAM5 5CAM6 6CAM7 7CAM8 8CAM9 9CAM10 10CAM11 11CAM12 12CAM13 13CAM14 14CAM15 15CAM16 16
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
CAM1Camera Title1CAM2 2CAM3 3CAM4 4CAM5 5CAM6 6CAM7 7CAM8 8CAM9 9CAM10 10CAM11 11CAM12 12CAM13 13CAM14 14CAM15 15CAM16 16 
						

							95

0123456789ABCDEFGHIJKLMNOPQRSTUVW
XYZabcdefghijklmnopqrstuvwxyzÄÅÇÉÑÖ›Ü
áàâäãåçéèêëíìîïñóòôöõúùûü?"#&()
*+,-./:;SP
Note:To correct the entered characters, move the cur-
sor to the character to be corrected and press the
STOP button to delete it. Enter a correct character
after deleting.
[Screenshot 4]
The camera title is entered.
bPress the SETUP/ESC button.
→The camera title will be set and the setting window
of the camera title will be closed.
Note:It is possible to set Camera Title [Display] to dis-
play a camera title on monitor 2 and Camera Title
[Embedded] to embed/display a camera title on
monitor 1 individually using a PC via a network.
Refer to the Network Setup Instruction (PDF) for fur-
ther information.
8Camera Title Display Position
Select a camera title display position from the following.
L-UPPER:Displays a camera title at the upper left of the
screen.
L-LOWER:Displays a camera title at the lower left of the
screen.
R-UPPER:Displays a camera title at the upper right of the
screen.
R-LOWER:Displays a camera title at the lower right of the
screen.
CENTER:Displays a camera title at the center of the
screen.
Note:When setting the camera title to be recorded togeth-
er with images, the camera title display will be embed-
ded in the selected position.
Refer to page 111 for further information about
Embedded REC (title).
8Live Sequence
Perform the settings for the sequential display of live
images as follows.[Screenshot 1]
Start operation from the Display menu.
zMove the cursor to Live Sequence using the arrows
button (CD) and press the SET button.
[Screenshot 2]
The Live Sequence pop-up menu will be displayed.
xMove the cursor to CAM of STEP 1 using the arrows
button.
[Screenshot 3]
The cursor moves to CAM.
cSelect how to display images from camera channels in
STEP 1 from the following by rotating the jog dial.
1, 2, ... , 16:Displays an image from the selected cam-
era channel on a single screen.
1 - 4:Displays images from camera channels
1 - 4 on a 4-split screen.
5 - 8:Displays images from camera channels
5 - 8 on a 4-split screen.
9 - 9 (only for the WJ-HD309A):Displays an image
from camera channel 9 on the upper left area on a
4-split screen.
9 - 12 (only for the WJ-HD316A):Displays images
from camera channels 9 - 12 on a 4-split screen.
13 - 16 (only for the WJ-HD316A):Displays images
from camera channels 13 - 16 on a 4-split screen.
1 - 9:Displays images from camera channels 1 - 9 on a
9-split screen.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Saving) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
CAM1Camera Title1CAM2CAM3 3CAM4 4CAM5 5CAM6 6CAM7 7CAM8 8CAM9 9CAM10 10CAM11 11CAM12 12CAM13 13CAM14 14CAM15 15CAM16 16
ENTRANCE
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Savings) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Saving) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s Monitor 1 Monitor 2
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Saving) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s Monitor 1 Monitor 2 
						

							96
10 - 16 (only for the WJ-HD316A):Displays images
from camera channels 10 - 16 on a 9-split screen.
--:Skips the selected step.
vWhen displaying images from camera channels 1 - 16
on a single screen is selected in step 3, select the cam-
era position.
Move the cursor to PRESET in STEP 1 using the
arrows button.
[Screenshot 4]
The cursor moves to the PRESET in STEP 1.
bRotate the jog dial to select a preset position number
for which image is displayed in STEP 1 from the follow-
ing.
1 - 256:Moves to the selected preset number.
--:Does not move to the preset position.
nSelect DWELL in STEP 1 using the arrows button.
[Screenshot 5]
The cursor moves toDWELL in STEP 1.
mRotate the jog dial to select an interval time to go to the
next sequential step from 1 - 30 seconds (in 1 second
intervals).
The sequence step is skipped when 0 s is selected.
Repeat steps 2 and 7 to set for the other sequence
steps.
,Press the SETUP/ESC button.
→The settings for the sequential display are set and
the sequence setting menu closes.
8Summer Time (Day Light Savings)
Select the method of switching to summer time from the fol-
lowing.
OUT:Does not function.
IN:Applies summer time.
AUTO:Applies summer time in accordance with the setting
of summer time.
8Beep (Operation)
Select ON or OFF whether or not to sound the buzzer when
operating the buttons.
ON:Sounds the buzzer when operating the buttons.
OFF:Does not sound the buzzer when operating the but-
tons.
8Language
Select a language for the SETUP MENU from the following.
JAPANESE/ENGLISH/FRANÇIS/ESPAÑOL/DEUTSCH/
ITALIANO/RUSSIAN/CHINESE
Important:
Displaying the language of the browser used to access
the unit from a PC will not be changed even though this
setting is changed.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Saving) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s Monitor 1 Monitor 2
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu
::
 Date Format Time  Format Time & Date
 Time & Date Display Position Camera Title Camera Title Display Position Live Sequence Summer Time (Day Light Saving) Beep (Operation) LanguageMMM.DD.YY
12h
PM
      SET
L-UPPER
    SETUP
R-LOWER
    SETUP
AUTO
ON
ENGLISH
JAN  .04 10 00 00 1    .
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s
STEPCAMPRESETDWELL11--2s22--2s33--2s44--2s55--2s66--2s77--2s88--2s99--2s1010--2s1111--2s1212--2s1313--2s1414--2s1515--2s1616--2s Monitor 1 Monitor 2 
						

							97
Resolution [Screenshot 2]
The REC Camera pop-up menu will be displayed.
xSelect the desired camera channel for manual record-
ing/event recording using the arrows button (CDA
B) and rotate the jog dial. It is possible to select a cam-
era channel by pressing a camera channel selection
button (1 - 16 for the WJ-HD316A, 1 - 9 for the WJ-
HD309A) on the front panel of the unit.
cPress the SETUP/ESC button.
→The settings will be applied and the REC camera
pop-up menu will be closed.
8Resolution
Select a recording resolution from the following.
FRAME 3D ON:High resolution (720 x 480), with camera
shake compensation
FRAME 3D OFF:High resolution (720 x 480)
FIELD:Standard resolution (720 x 240)
SIF:Low resolution (360 x 240)
Recording will not be performed for around 4 seconds
when the SETUP MENU (Quick) was closed after changing
the settings.
Note:It is possible to minimize blurring to record fast mov-
ing objects by selecting FRAME 3D ON.
8Manual REC
Perform the recording rate (REC Rate) and the image quali-
ty (Quality) for manual recording.
The following are available for the recording rate.
OFF/2 ips/3 ips/5 ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/
60 ips/120 ips
Note:The available recording rate differs depending on the
selected solution.
[REC & Event]
Perform the settings for the basic recording and the set-
tings for event actions of each event type (motion detection,
video loss, command alarm and terminal alarm.)
8REC Type
Select QUICK or ADVANCED for validation of the record-
ing settings.
QUICK:The recording settings set on the SETUP MENU
(Quick) will be validated when recording.
ADVANCED:The recording settings set on the SETUP
MENU (Advanced) will be validated when recording.
Note:When QUICK is selected for REC Type of REC &
Event, the SETUP MENU (Quick) will be displayed by
pressing the SETUP/ESC button for 2 seconds or more.
When ADVANCED is selected for REC Type of REC
& Event, the SETUP MENU (Advanced) will be dis-
played by pressing the SETUP/ESC button for 2 sec-
onds or more.
8REC Camera
Select a camera channel for manual recording/event
recording.
[Screenshot 1]
Start operation from the REC & Event menu.
zMove the cursor to REC Camera using the arrows but-
ton (CD) and press the SET button.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
REC Camera123 4 5 6 7 8
910111213141516
FRAME 3D ON/FRAME 3D OFF
FIELD 
SIFMaximum recording rate
30 ips
60 ips
120 ips
Note:The camera channel number selected for REC
Camera will be displayed next to the selected record-
ing rate. 
						

							98
The following are available for the image quality.
SFA/SFB:Top quality (SUPER FINE)
FQA/FQB:High quality (FINE)
NQA/NQB:Standard quality (NORMAL)
EXA/EXB:Low quality (EXTENDED)
**A is suitable for less dynamic images.
**B is suitable for more dynamic images.
8Event REC
Perform the recording rate (REC Rate) and the image quali-
ty (Quality) for event recording (recording to be performed
at event occurrence (motion detection, video loss, terminal/
command alarm and terminal alarm)).
The following are available for REC Rate (recording rate).
OFF/2 ips/3 ips/5 ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/
60 ips/120 ips
Note:The camera channel number selected for REC
Camera will be displayed next to the selected record-
ing rate.
Note:The available recording rate differs depending on the
selected solution.
The following are available for Quality (image quality).
SFA/SFB:Top quality (SUPER FINE)
FQA/FQB:High quality (FINE)
NQA/NQB:Standard quality (NORMAL)
EXA/EXB:Low quality (EXTENDED)
**A is suitable for less dynamic images.
**B is suitable for more dynamic images.
The following are available for Time (recording duration).
1 s - 10 s (in 1 second intervals)/20 s/30 s/1 min - 10 min
(in 1 minute intervals)/20 min/30 min/ 40 min/ 50 min/
60 min
MANUAL:Recording duration differs depending on the
event type as follows;
When a motion is detected:Recording will be per-
formed for 8 seconds
When a video loss has occurred:Recording will be
performed while the video signal is lost. 
When a terminal alarm has occurred:Recording will
be performed while the alarm signal is being sup-
plied.
When a command alarm has occurred:Recording will
be performed for 8 seconds.
CONTINUE:Record until the ALARM RESET button is
pressed.Note:When MANUAL is selected for Time (recording
duration), recording will be performed for at least 8
seconds at an event occurrence as long as the
alarm is not canceled.
The following are available for Operation Mode (event
action mode). Refer to page 49 for further information about
each event action mode.
ACT DET (Activity Detection Mode):Performs only
recording, writing an event log and camera movement
to a preset position at an event occurrence. Other event
actions will not be performed.
ALARM (Alarm Mode):Performs every event action
according to the settings.
OFF:Performs only recording of the event log. Other event
actions will not be performed.
8Event Setup
Perform the settings for the alarm output duration and the
buzzer sound duration for each event type (motion detec-
tion, video loss, command alarm and terminal alarm).
[Screenshot 1]
Start operation from the REC & Event menu.
zMove the cursor to Event Setup using the arrows but-
ton (CD) and press the SET button.
[Screenshot 2]
The Event Setup pop-up menu will be displayed.
xMove the cursor to the item to be set using the arrows
button (CD), and rotate the jog dial to select the para-
meter.
The following are available for Alarm Output (alarm
output duration).
When OFF is selected, the alarm output will not be sup-
plied.
(s: second, min: minute)
OFF:No alarm output is supplied.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
Event Setup VMD
       Alarm Output
       Buzzer
 Video Loss
       Alarm Output
       Buzzer
 Terminal/Command Alarm
       Alarm Output
       Buzzer
OFF
OFF
--
2s
2s
2s
Resolution
FRAME 3D ON/FRAME 3D OFF
FIELD
SIFMaximum recording rate
30 ips
60 ips
120 ips 
						

							99
1 s - 30 s (in 1 second intervals)/40 s/50 s/1 min/
2 min/3 min/4 min/5 min
EXT:Alarm output will continue until the ALARM RESET
button is pressed.
The following are available for Buzzer (buzzer sound
duration).
When OFF is selected, a buzzer will not sound.
(s: second, min: minute)
1 s - 30 s (in 1 second intervals)/40 s/50 s/1 min/
2 min/3 min/4 min/5 min
EXT:The buzzer will continue until the ALARM RESET
button is pressed.
OFF:The buzzer will not sound.
cPress the SETUP/ESC button.
→The settings for Alarm Output and Buzzer will be
applied and the Event Setup pop-up menu will be
closed.
8Power ON Manual REC
Select ON or OFF to determine whether or not to start
recording when the power is turned on by the connected
external timer (or the switch).
ON:Manual recording will start automatically after complet-
ing the system check.
OFF:Manual recording will not start automatically after
completing the system check.
Important:
When ON is selected, manual recording will start auto-
matically after completing the system check.
8VMD Setup
Select ON or OFF to determine whether to enable or dis-
able the motion detection function for each camera chan-
nel.
When ON is selected, perform the settings for the motion
detection area for each camera channel. Up to 4 areas can
be set for a camera channel for the detection area. Refer to
page 114 for further information about the motion detection
function.
[Screenshot 1]
Start operation from the REC & Event menu.
zMove the cursor to VMD Setup using the arrows button
(CD) and press the SET button.[Screenshot 2]
The VMD Setup pop-up menu will be displayed.
xSelect the camera channel to be set by using the
arrows button (CD).
cRotate the jog dial to select ON for a desired camera
channel for which the motion detection function is to be
applied, and press the SET button.
[Screenshot 3]
The VMD Area Setup window will be displayed.
vMove the cross cursor to a desired point to be set as
the start point of the motion detection area using the
arrows button, and press the SET button.
Note:To set all areas on the monitor as the motion
detection area, select ALL AREAS and press the
SET button.
[Screenshot 4]
The start point of the motion detection area is assigned.
bMove the cross cursor to a desired point to be set as
the end point of the motion detection area using the
arrows button (CDAB), and press the SET button.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
VMD Setup
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF 
						

							100
[Screenshot 5]
The motion detection area is set with the start point and the
end point as the points at opposite angles of the motion
detection area.
nRepeat steps 4 and 5 to set another motion detection
area.
Up to 4 areas can be set. The newly created areas will
be named automatically as A, B, C and D in the order of
creation.
mTo complete the settings, rotate the jog dial to select
EXIT on the status bar, and press the SET button.
[Screenshot 6]
The VMD Setup window will be closed and the VMD
Setup pop-up menu will be displayed.
,Press the SETUP/ESC button.
→The VMD Setup pop-up menu will be closed.
Notes:
•Refer to page 115 for descriptions of how to delete
the motion detection area.
•It is possible to set the sensitivity and the detection
mode (method of detection) of each detection area.
Refer to page 115 for further information.[Network]
Perform the settings for the network such as the IP address
and the gateway address when operating this unit a PC via
a network such as a LAN.
8Line Speed
The following are available for Line Speed.
AUTO:Line speed will be applied automatically.
10-HALF:10 Mbps half duplex
10-FULL:10 Mbps full duplex
100-HALF:100 Mbps half duplex
100-FULL:100 Mbps full duplex
Note:When the SETUP MENU is closed after changing the
line speed, the unit will automatically restart.
8HTTP Port Number
Specify the HTTP port number to be used to transfer
images from this unit. It is not necessary to change it for
normal use.
8DHCP
Select ON or OFF whether or not to use the DHCP server.
When obtaining IP addresses, net mask and a gateway
address from the DHCP server, set to ON.
If not, set to OFF and enter those addresses manually.
ON:Uses the DHCP server.
OFF:Does not use the DHCP server.
8IP Address
Enter an IP address when OFF is selected for DHCP.
For this unit, enter 4 units from the decimal numbers (0-
254).
8Subnet Mask
Enter a subnet mask according to the network configuration
when OFF is selected for DHCP.
8Gateway
Enter the gateway address according to the network con-
figuration when OFF is selected for DHCP.
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu Line Speed HTTP Port Number DHCP IP Address Subnet Mask GatewayAUTO
00080
OFF192 168 000 250
255 255 255 000
192 168 000 001
SETUP MENULIVEQuickDisplay
REC & Event
Network
Advanced Menu REC Type REC Camera Resolution Manual REC
       REC Rate
       Quality
 Event REC
       REC Rate
       Quality
       Time
       Operation Mode
 Event Setup Power ON Manual REC VMD  SetupQUICK
    SETUP
FIELD
30ips / 16CH
FQB
30ips / 16CH
FQB
30s
ALARM
    SETUP
OFF
    SETUP
VMD Setup
CAM1
CAM2
CAM3
CAM4
CAM5
CAM6
CAM7
CAM8OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF CAM9
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF