Panasonic Digital Disk Recorder Wj Hd200 Operating Instructions

							61
8On/Off (ON/OFF)
ON:Displays the camera title.
OFF:Hides the camera title.
8Title (TITLE)
Usable characters:Are shown in the window.
Number of digits:5 digits maximum.
8Title Position (POSITION)
Right-Lower:Displays the title in the lower right corner.
Right-Upper:Displays the title in the upper right cor-
ner.
Left-Lower:Displays the title in the lower left corner.
Left- Upper:Displays the title in the upper left corner.
Click the [SET] button when all items have been set proper-
ly.
System Setup (SYSTEM SETUP)
8Password Lock (PASSWORD LOCK)
Buttons on the front panel of the WJ-HD200 will be 
password-protected or freed.
ON:Enables password-protection.
OFF:Disables password-protection.
8Password All (PASSWORD ALL)
Enter a five-digit password comprising 1 through 8 to
protect normal operations and setup operations from
unauthorized access.
Available numerals:From 11111 to 88888
8Status Display (STATUS DISPLAY)
ON:Status display is enabled.
OFF:Status display is disabled.
8Status Display Position (STATUS POSITION)
Right-Lower:Displays status in the lower right corner.
Right-Upper:Displays status in the upper right corner.
Left-Lower:Displays status in the lower left corner.
Left-Upper:Displays status in the upper left corner.
8HDD Full (HDD FULL)
1% - 99%:The FULL indicator blinks when the remain-
ing capacity reaches the selected value. This will
take effect when DISK END MODE is set to STOP in
the RECORD SETUP.
8Remote LED (REMOTE LED)
ON:REMOTE LED turns on when the network controls
the recorder. 
OFF:REMOTE LED is deactivated.
8HDD Check (HDD CHECK)
ON 0:00 - 23:00:The recorder checks the HDD at the
specified time every day.
OFF: Check is deactivated.
Click the [SET] button when all items have been set proper-
ly.
Click the [CAMERA TITLE SETUP] button to open the CAM-
ERA TITLE window.
Camera Title (CAMERA TITLE) 
						

							62
8Password Operation (PASSWORD OPERATION)
Enter a five-digit password to protect normal operations
from unauthorized access.
Available numerals:From 11111 to 88888
8Keylock Buzzer (KEYLOCK BUZZER)
The buzzer will beep or not when a locked button is
pressed.
ON:Enables the buzzer beep.
OFF:Disables the buzzer beep.
8Skip Alarm Recall (SKIP ALARM RECALL)
Specify the number of pages to be skipped in the alarm
log. The alarm log page will jump the specified pages
when the JogDial is rotated.
Available skip pages:1, 5, 10, 20, 50
8Simultaneous Recording and Playback
(SIMULTANEOUS REC&PLAY)
There may be cases where recording is essential while
playback is in progress.
ON:Allows both recording and playback at a time.
OFF:Allows exclusively recording or playback.
Note: The recording rate may be sacrificed in the fol-
lowing cases.
•Recording and playback/FTP access are carried
out simultaneously.
•A multi-split screen is displayed.
•VMD (video motion detection) is enabled.
•A PC accesses the live images via the network.
8Alteration Detection (ALTER DETECT)
You can enable or disable the addition of alteration-
detection signals in the JPEG data supplied to the net-
work. The default is OFF.
ON:Detects alterations.
OFF:Does not detect.
Note:When set to ON, the data transmission rate on
the network will slow down.
8Disk End Mode (DISK END MODE)
STOP:Stops recording until a mode other than [STOP]
is selected.
CONTINUE: Old data is automatically overwritten from
the disk start.
8Disk End Buzzer (DISK END BUZZER)
ON:Enables the buzzer beep at the disk end (remain-
ing space = 0 %).
OFF: Disables the buzzer beep.
8Play Priority (PLAY PRIORITY)
This setting places priority on a specific access point
for playing back the image data when access collisions
take place.
LOCAL:Places priority on front panel operations.
NET PLAY:Places priority on network access.
FTP GET:Places priority on access to the FTP.
NONE:The latest operation has priority over others.
8Time Adjusting (TIME ADJUSTING)
The internal timer built into the WJ-HD200 is calibrated
once a day via the Time Adjust In and Out terminals on
the rear panel.
SLAVE:Accepts the calibration signal from the master.
MASTER:Supplies the calibration signal to the slave
units at the specified hour every day. 
						

							63
Video Motion Detector Setup
(VMD SETUP)
8Sensitivity (SENSITIVE)
LOW:Low sensitivity
MID:Medium sensitivity
HIGH: High sensitivity
OFF:Motion detection is disabled.
Click the [SET] button when all items have been set proper-
ly.
Click the [SETUP] button to open the area setup window.
VMD Area Setup (VMD AREA
SETUP)
Drag a maximum of four areas with the mouse to specify
the detection areas.
Click the [SET] button when all items have been set proper-
ly.
Alarm Setup (ALARM SETUP)
8Alarm Buzzer (ALARM BUZZER)
ON:Buzzer beeps while alarm is active.
OFF:Buzzer does not beep.
8Video Loss Detection (VIDEO LOSS DETECT)
OFF:Deactivates the video loss detection.
ON:Activates the detection.
8Monitoring Mode (MONITOR MODE)
SPOT: Switches to the picture of the channel where
alarm has operated.
OFF:Retains the previous display mode.
Click the [SET] button when all items have been set proper-
ly. 
						

							64
8Parity Check (PARITY CHECK)
NONE:No parity check
EVEN: Even parity
ODD:Odd parity
8Stop Bit (STOP BIT)
1 bit: 1 bit
2 bit:2 bits
8Wait Time (WAIT TIME)
OFF:Retransmission is disabled.
100 MSEC: 100 m seconds
200 MSEC:200 m seconds
1 SEC: 1 second
8System Unit Address (SYSTEM UNIT ADDRESS) 
(only for PS
•DATA)
Assignable addresses:From 1 to 99, must be unique
in the chain.
8Control Unit Addresses 
(CONTROL UNIT ADDRESS) (only for PS
•DATA)
Assignable address:From 1 to 99, must be unique in
the chain.
8Alarm Data (ALARM DATA)
OFF: Select this when no system controller is connect-
ed.
0 SEC: Does not pause.
1 SEC: Pauses for 1 second.
5 SEC:Pauses for 5 seconds.
Click the [SET] button when all items have been set proper-
ly.
Click the [CAMERA NO. SETUP] button. The CAMERA
NUMBER SETUP window opens.
Communication Setup
(COMMUNICATION SETUP)
Click the [SERIAL PORT SETUP] or [NETWORK SETUP]
button. The respective window opens.
Serial Port Setup 
(SERIAL PORT SETUP)
8Protocol Selection (PROTOCOL SELECT)
PS•DATA: Select when the communication chain uses
the PS
•DATA protocol.
When selected, the DATA terminal on the rear panel
can be used.
RS-232C: Select when other than PS•DATA is used. 
When selected, the RS-232C terminal on the rear
panel can be used.
8Baud Rate (BAUD RATE) 
4800: 4 800 bps
9600: 9 600 bps
19200: 19 200 bps
8Data Bit (DATA BIT) 
7: 7 bits 
8: 8 bits 
						

							65
IP Address (IP ADDRESS) 
The IP address is displayed. Enter from the keyboard.
Netmask (NETMASK)
The netmask is displayed. Enter from the keyboard.
Default Gateway (DEFAULT GATEWAY) 
The default gateway is displayed. Enter in from the key-
board.
8Domain Name Service (DOMAIN NAME SERVICE)
OFF:Disables DNS, only IP address usable.
MANUAL:Enables DNS.
AUTO:Enables DNS.
Domain Name (DOMAIN NAME)
Enter from the keyboard.
DNS Server Address (DNS SERVICE ADDRESS)
Enter from the keyboard.
8Dynamic DNS (DYNAMIC DNS)
OFF:
Does not use DDNS.
ON:Uses DDNS.
DDNS Host Name (DDNS HOST NAME)
Enter from the keyboard. 
DDNS User Name (DDNS USER NAME)
Enter from the keyboard. 
DDNS Password (DDNS PASSWORD)
Enter from the keyboard. 
DDNS Access Interval (DDNS ACCESS INTERVAL)
Enter from the keyboard.
8Simple Network Management Protocol
Note: (double quotation) cannot be used for SNMP.
Camera Number Setup
(CAMERA NUMBER SETUP)
(only for PS
•DATA)
Assignable numbers:From 1 to 128, must be unique
in the chain.
Click the [SET] button when all items have been set proper-
ly.
Network Setup (NETWORK
SETUP)
8Line Speed (LINE SPEED)
AUTO: The speed is automatically selected.
100Mbps (FULL DUPLEX):100 mega byte, full duplex
100Mbps (HALF DUPLEX): 100 mega byte, half
duplex
10Mbps (FULL DUPLEX): 10 mega byte, full duplex
10Mbps (HALF DUPLEX): 10 mega byte, half duplex
8HTTP Server Port (HTTP SERVER PORT)
Enter from the keyboard. The default setting is 80.
8DHCP On/Off (DHCP ON/OFF)
Select ON or OFF for DHCP (Dynamic Host
Configuration Protocol).  
						

							66
SNMP Community (SNMP COMMUNITY)
Enter from the keyboard.
SNMP Contact (SNMP CONTACT)
Enter from the keyboard. 
SNMP System Name (SNMP SYSTEM NAME)
Enter from the keyboard. 
SNMP System Location (SNMP SYSTEM LOCATION)
Enter from the keyboard.
Click the [SET] button when all items have been set proper-
ly.
The WJ-HD200 will restart, and you will be requested to
enter the URL as described earlier in Main Page and
Control Panel.
Switcher Setup (SWITCHER
SETUP)
This window specifies sequence setups only for the WJ-
HD200. The browsers sequence is set up in LIVE
SEQUENCE SETUP on page 71.
8Common Setup (COMMON SETUP)
Start Display (START DISPLAY) 
The image in the selected form will be displayed on the
monitor when the unit is turned on.
Single image:CH 1 – CH 8
Quad image:QUAD-4A (including 1-4), QUAD-4B
(including 5-8)
Multi image:9-SCREEN (including 1-8)
Sequence:SPOT SEQUENCE, MULTI SEQUENCE
Multiscreen Selection Mode (MULTI SELECT MODE)
When the [MULTISCREEN SELECT] button on the front
panel is pressed, the monitor display will be switched
as follows depending on the setup.
QUAD ONLY:QUAD-4A →QUAD-4B →QUAD-4A
ALL:QUAD-4A →QUAD-4B →9-SCREEN →
QUAD-4A 
8Multiscreen Sequence Setup 
(MULTI SEQUENCE SETUP) 
Sequence Timing (SEQUENCE TIMING) 
INT:
The time preset on the internal timer allows the
sequence to move a step forward.
EXT:The SEQ IN signal on the rear panel allows
the sequence to move a step forward.
Auto Skip (AUTO SKIP)
ON:
The sequence skips any step where no video
is input.
OFF:The sequence does not skip the step.
Click the button to open the Multi Sequence Setup window.
8Spot-screen Sequence Setup
(SPOT SEQUENCE SETUP)
Sequence Timing (SEQUENCE TIMING)
INT: 
The time preset on the internal timer allows the
sequence to move a step forward.
EXT:SEQ IN signal to the rear panel allows the
sequence to step forward.
Auto Skip (AUTO SKIP)
ON:
The sequence skips any step where no video
is input.
OFF:The sequence does not skip the step.
Click the button to open the Spot Sequence Setup window.
8Camera View Setup (CAMERA VIEW SETUP)
Click the button to open the Camera View Setup window.
Multi Sequence Setup (MULTI
SEQUENCE SETUP) 
						

							67
8Camera Channel (CAMERA CH)
1 - 8:The selected camera image will be displayed in
single spot mode.
QUAD 4A: Camera images 1 through 4 will be dis-
played in quad-split mode.
QUAD 4B:Camera images 5 through 8 will be dis-
played in quad-split mode.
8Time (TIME)
Available times: 2-30 S
Click the [SET] button when all items have been set proper-
ly.
Spot Sequence Setup (SPOT
SEQUENCE SETUP)
8Camera Channel (CAMERA CH)
1 - 8:The selected camera image will be displayed.
OFF: The blackout screen will be displayed.
8Time (TIME)
Available times:2-30 S
Camera View Setup (CAMERA
VIEW SETUP)
8Mode (MODE)
ON: The live image of the channel is displayed.
OFF:The blackout image is displayed.
Click the [SET] button when all items have been set proper-
ly.
System Information (SYSTEM
INFORMATION)
8HDD Hour Meter (HDD HOUR METER) 
Each meter shows how many hours the digital hard disk
recorder has been operated in playback, recording and
idle. The built-in HDD needs replacement when the
hour meter reads around 30 000 H. 
8HDD Capacity (HDD CAPACITY)
The total usable capacity of the built-in hard disk is indi-
cated. 
						

							68
8System Software Version (SYSTEM VERSION) 
This line displays the version number of the installed
system software.
8MAC Address (MAC ADDRESS)
A MAC (Media Access Control) address is displayed. 
8IP Address (IP ADDRESS)
The IP address is displayed.
8Subnet Mask (SUBNET MASK)
The subnet mask is displayed.
8Gateway (GATEWAY)
The gateway is displayed.
8Domain Name (DOMAIN NAME)
The domain name is displayed when it is set to ON in
the network setup. 
8DNS Server Address (DNS SERVER ADDRESS)
The DNS server address is displayed when it is set to
ON in the network setup. 
System Log (SYSTEM LOG)
Click the [SYSTEM LOG] button in the SYSTEM INFORMA-
TION window to open the log.
Error causes are abbreviated as shown at the top of the
window. 
						

							69
User Setup (USER SETUP)
A maximum of 16 users can be registered.
8User Authorization (USER AUTHORIZATION)
OFF:Allows free access.
ON: Verifies the password and access level for a maxi-
mum of sixteen users.
Click the [SET] button.
8User Name (USER NAME)
Enter from the keyboard. The default is admin.
8Password (PASSWORD)
Enter from the keyboard. The default is admin.
8Access Level (ACCESS LEVEL)
The default is [1].
[1] ADMINISTRATOR:Allows access to the setup
parameters, live and playback images.
[2] LIVE MONITORING & PLAYBACK:Bans access to
the setup parameters.
[3] LIVE MONITORING ONLY:Allows only monitoring
of live images.
Click the [SET] button when all items have been set proper-
ly.
8Deleting Users (DELETE USER)
Enter or select the user name you wish to erase, and
click the [DELETE] button.
Host Setup (HOST SETUP)
A maximum of 8 hosts can be registered.
8Host Authorization (HOST AUTHORIZATION)
OFF: Allows free access.
ON: Verifies the host address and access level for a
maximum of eight hosts.
Click the [SET] button.
8Set Host Allowed to Access (SET HOST
ALLOWED TO ACCESS )
HOST ADDRESS: enter from the keyboard. 
Click the [SET] button.
8Deleting Hosts (DELETE HOST)
Enter or select the host address you wish to erase, and
click the [DELETE] button.
Note:Do not enter text lines effective as the HTML tag from
the keyboard to the input columns. Other wise, the
menu setup using HTML files may malfunction. If this
happens, you need to initialize the settings by referring
to DEFAULT described in page 41.
NETWORK CONFIGURATION 
						

							70
Interval (INTERVAL)
Available times: 
1 - 1 440 seconds, 1 - 1 440 min-
utes
Channel to Send (CHANNEL TO SEND)
OFF:
Does not send the channel image.
ON:Sends the channel image.
Click the [SET] button when all items have been set proper-
ly.
FTP Client Setup (FTP CLIENT
SETUP)
8Basic Setup (BASIC SETUP)
Server Address (SERVER ADDRESS)
Enter the server address.
Login User Name (LOGIN USER NAME)
Enter the user name.
Login Password (LOGIN PASSWORD)
Enter the password.
Mode (MODE)
Available modes: 
SEQUENTIAL, PASSIVE
Click the [SET] button.
8FTP Send by Periodic Timer (FTP SEND BY
PERIODIC TIMER)
FTP Sending (FTP SENDING)
ON: 
Sends the channel images at the specified
interval.
OFF:Does not send.
Server Directory (SERVER DIRECTORY)
Enter the directory where you store the image data.
File Name (FILE NAME)
File Name Rule: 
Date & time basis, Serial number-
ing