Panasonic Digital Disk Recorder Wj Hd200 Operating Instructions

							31
3. Select either ON or OFF with the JogDial.
The default is ON for all cameras.
ON:Enables camera title display, title registration, and
position selection.
OFF:Disables the camera title functions.
4. Press the JogDial (SET) to validate the selection.
When ON is selected, go to the following steps. The
cursor moves to the title edit area.
When OFF is selected, return to step 2 above, or press
the [SETUP/ESC] button to escape from the CAMERA
TITLE menu.
5. 
5-1 Select a character for the digit with the JogDial.
Each title is identical to the camera number: 1, 2, 3,
and so forth as the default.
Available characters are as follows.
0 ~ 9   A ~ Z   !   %   &
(   )   *   –   /   :   .   ?
←→↑↓  •
5-2 Press the JogDial to validate the selection for the
digit. 
The selected character is displayed on the digit,
and the cursor goes to the right digit. 
5-3 Press the [SETUP/ESC] button to move the cursor
back to the previous digit.
5-4 Repeat steps 5-1, 5-2 and 5-3 until all digits are
entered.
5-5 Press the JogDial when the cursor is on the right
end digit to validate the entered title. The cursor
moves to the POSI. column.
Note:A bullet (centered dot) stands for a space used
for deleting entered characters.
6. Select a display position with the JogDial.
The default setting for cameras 1, 2, 5, and 6 is R-
LOWER, for cameras 3, 4, 7, and 8 R-UPPER.
R-LOWER:Displays the camera title in the lower right
corner.
R-UPPER:Displays the camera title in the upper right
corner.
L-LOWER:Displays the camera title in the lower left
corner.
L-UPPER:Displays the camera title in the upper left
corner.
Note:When the 9-split screen is displayed, the camera title
position is fixed to R-LOWER. 
7. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
System Setup (SYSTEM SETUP)
There are two pages of the system setup. To turn a new
page, continue to move the cursor with the [
D] or [C] but-
ton.
Password Lock Setup (PASSWORD
LOCK)
A five-digit password is entered to protect all settings,
recorded pictures, and operating status against erroneous
operation and tampering. Settings alone can be also pro-
tected from unauthorized access. While the LOCK indicator
on the front panel is on, a message NOW KEY LOCKED!
is displayed to warn unauthorized operators. If accessed in
this condition, the buzzer beeps.
1. Move the cursor to PASSWORD LOCK with the [
D] or
[
C] button.
OPERATEALARM
SUSPEND
RESETOSD
TIMER DST
REMOTE
LOCK
SE
   SYSTEM SETUP (1 OF 2)
PASSWORD LOCK   OFF
  ALL
→          ***** 
  OPERATION→    *****
KEYLOCK BUZZ    ON
SKIP ALM-RECALL  1PAGE
SIMUL REC&PLAY  ON
ALTER DETECT    OFF
DISK END MODE   CONTINUE
DISK END BUZZ   ON
   SYSTEM SETUP (1 OF 2)
PASSWORD LOCK   OFF
  ALL
→          ***** 
  OPERATION→    *****
KEYLOCK BUZZ    ON
SKIP ALM-RECALL  1PAGE
SIMUL REC&PLAY  ON
ALTER DETECT    OFF
DISK END MODE   CONTINUE
DISK END BUZZ   ON
   SYSTEM SETUP (2 OF 2)
PLAY PRIORITY   LOCAL
TIME ADJUST SETUP
O
AUTO ERASING    OFF 
						

							32
2. Select either ON or OFF with the JogDial, and press the
JogDial.
The default is OFF.
ON:The buttons are password protected. The recorder
enters the button lock mode if neither a button nor
the JogDial is operated within a period of five min-
utes.
OFF:No password protection is applied.
3. Move the cursor to ALL
→or OPERATION→with the
[
D] or [C] button.
ALL:Allows both normal operations and setup opera-
tions.
OPERATION:Allows only normal operations. Setup
operations are not allowed.
4. Press the JogDial.
The preset password appears.
The default is 12345 for both ALL and OPERATION.

5. Select a digit, rotating the JogDial.
6. Enter a number with the numeric button, and press the
JogDial.
The cursor moves one digit to the right.
7. Repeat steps 5 and 6 until all digits are entered.
8. Press the [SETUP/ESC] button to confirm the entered
password.
Go back to step 3 if you have not yet set the OPERA-
TION password.
Keylock Buzzer Setup (KEYLOCK
BUZZ)
1. Move the cursor to KEYLOCK BUZZ with the [D] or [C]
button.
2. Select either ON or OFF with the JogDial, and press the
JogDial.
The default is ON.
ON:Buzzer beeps when unauthorized access takes
place.
OFF:Buzzer does not sound.
Skip Alarm Recall Setup
(SKIP ALARM RECALL)
Alarm log pages are recalled on the monitor when the
JogDial is pressed for 2 seconds. When searching in the
log, you may need to skip pages. The page will skip the
specified number forward or backward from the displayed
page when rotating the JogDial.
1. Move the cursor to SKIP ALM RECALL with the [
D] or
[
C] button, and press the JogDial.
2. Select the number of skip pages with the JogDial, and
press the JogDial.
The default is 1 page.
Available skip pages:1, 5, 10, 20, 50 pages
Simultaneous Recording & Playback
(SIMUL REC&PLAY)
This setting specifies whether to allow simultaneous play-
back and recording. When the parameter is set to ON, the
default of the recording rate will be changed to 15 FPS.
1. Move the cursor to SIMUL REC&PLAY with the [
D] or
[
C] button.
2. Select on or off with the JogDial, and press the JogDial.
The default is ON.
ON:Allows simultaneous recording and playback
including remote-access playback and FTP access.
The default recording rate is 15 FPS, and the high-
est rate is 30 FPS.
OFF:Places priority on recording triggered by pressing
the REC button or by an alarm input. Playback
including remote-access playback and FTP access
will be interrupted if recording starts. The default
recording rate is 15 FPS, and the highest rate is 30
FPS.
Notes:
•A 30 FPS recording rate will decrease to 15 FPS
when playback, remote-access playback, or FTP
access is carried out simultaneously with recording.
   SYSTEM SETUP (1 OF 2)
PASSWORD LOCK   OFF
  ALL
→          ***** 
  OPERATION→    *****
KEYLOCK BUZZ    ON
SKIP ALM-RECALL  1PAGE
SIMUL REC&PLAY  ON
ALTER DETECT    OFF
DISK END MODE   CONTINUE
DISK END BUZZ   ON
   SYSTEM SETUP (1 OF 2)
PASSWORD LOCK   OFF
  ALL
→          ***** 
  OPERATION→    *****
KEYLOCK BUZZ    ON
SKIP ALM-RECALL  1PAGE
SIMUL REC&PLAY  ON
ALTER DETECT    OFF
DISK END MODE   CONTINUE
DISK END BUZZ   ON 
						

							33
•Simultaneous playback will pause prior to a time
space depending on the recording rate when the
playback area on the disk nears the recording area.
This is to avoid the access collision caused by the
simultaneous recording and playback in an area on
the disk.
0.1 FPS: 20 minutes maximum
1 FPS: 2 minutes maximum
7.5 FPS: 15 seconds maximum
15 FPS: 7 seconds maximum
•Even if preset to 30 or 15 FPS, the actual recording
rate may drop to 7.5 FPS at worst while busy multi-
tasks such as playback, remote-access playback,
remote-access live image, FTP access, multi-split
display, or video motion detection are carried out
simultaneously. The status display will indicate
*
→PLAY while playing back the images recorded
with a rate different from the preset.
Alteration Detection Setup
(ALTER DETECT)
You can enable or disable the recorder to add alteration-
detection signals in the JPEG data supplied to the network.
The default is OFF.
1. Move the cursor to ALT DET.
2. Select ON or OFF with the JogDial and press the
JogDial.
ON:Detects alterations.
OFF:Does not detect.
Note:When set to ON, the data transmission rate on
the network will slow down.
Disk End Mode Setup
(DISK END MODE)
The menu offers the following options at the point where the
available recording space on the disk is used up: [STOP],
[CONTINUE]1. Move the cursor to DISK END MODE with the [
D] or
[
C] button.
2. Select the desired mode with the JogDial, and press
the JogDial.
The default is CONTINUE.
STOP:Stops recording until a new mode other than
STOP is selected.
CONTINUE:Old data is automatically overwritten from
the disk start.
Note:Remaining capacity will be displayed on the monitor
by turning the JogDial counter-clockwise in recording
mode when STOP is selected.
Disk End Buzzer (DISK END BUZZ)
The buzzer can be set up to beep at the point where the
disk is full (remaining space 0 %). The setting is available
only when STOP is set for DISK END MODE.
1. Move the cursor to DISK END BUZZ with the [
D] or [C]
button.
2. Rotate the JogDial to select the desired parameter.
The default is ON.
ON:Enables the buzzer beep at the disk end (remain-
ing space 0 %).
OFF:Disables the buzzer beep.
Play Priority Setup (PLAY PRIORITY)
This setting places priority on a specific access point for
playing back the image data when access collisions take
place.
1. Move the cursor to PLAY PRIORITY.
2. Select an access point with the JogDial and press the
JogDial.
LOCAL:Places priority on front panel operations.
NET PLAY:Places priority on network access.
FTP GET:Places priority on access to the FTP.
NONE:The latest operation has priority over others.
DISK ENDDISK START
DISK ENDDISK START
DISK END DISK START
DISK END DISK START
Waiting for a new entry
Overwritten automatically
Stop
REC
Restart
REC
[STOP]
[Default] [CONTINUE]
   SYSTEM SETUP (1 OF 2)
PASSWORD LOCK   OFF
  ALL
→          ***** 
  OPERATION→    *****
KEYLOCK BUZZ    OFF
SKIP ALM-RECALL  1PAGE
SIMUL REC&PLAY  ON
ALTER DETECT    OFF
DISK END MODE   CONTINUE
DISK END BUZZ   ON 
						

							34
Time Adjust Setup
(TIME ADJUSTING)
IN and OUT terminals for a calibration signal are provided
on the rear panel. The master unit supplies the calibration
signal to the slave units once at the specified hour every-
day. The slave unit accepts the signal through the IN termi-
nal, and corrects its internal timer to the hour as far as the
clock deviates within 15 minutes after or before the hour.
This is convenient for synchronizing the internal clock with
other connected devices.
1. Move the cursor to TIME ADJUST SETUP
Oin the SYS-
TEM SETUP with the [
D] or [C] button, and press the
JogDial. The TIME ADJUST SETUP menu appears.
2. Select either MASTER or SLAVE with the JogDial, and
press the JogDial.
The default is SLAVE.
MASTER:The recorder supplies the calibration OUT
signal to the slave units.
SLAVE:The internal timer of the recorder is supplied
the calibration signal from the master.
3. Select the hour with the JogDial, and press the JogDial.
The hours:From 00:00 to 23:00
Note:You need not set the hour when SLAVE is select-
ed.
4. Press the [SETUP/ESC] button to go back to the SYS-
TEM SETUP menu.
Auto Erasing Setup
(AUTO ERASING)
The redundant records on the disk can be erased every
day at 24:00 midnight. The number of days specified by
this setting stand for the number of days the records will be
protected from the present, while the records older than
that will be erased.
1. Move the cursor to AUTO ERASING with the [
D] or [C]
button.
2. Select the desired number of days with the JogDial,
and press the JogDial.
OFF:Auto erasing is not applied.
1 DAY:Only today’s records from 00:00 onward are
protected. Records before 24:00 yesterday are
erased.
2 to 10DAYS:Records before the specified number of
days are erased.
14, 30, 45, 60, 90, 120, 150, 180DAYS:Same as
above.
Notes: 
•The number of days include today as 1 day, there-
fore 2DAYS covers today and yesterday.
•Auto erasing is implemented at 24:00 midnight.
Playback will stop once when the time reaches
24:00, then will restart with a different portion based
on the renewed day count.
   SYSTEM SETUP (2 OF 2)
PLAY PRIORITY   LOCAL
TIME ADJUST SETUP
O
AUTO ERASING    OFF
   TIME ADJUST SETUP
TIME ADJUSTING   SLAVE
 SET TIME
→        9:00 
						

							35
Alarm Setup (ALARM SETUP)
The digital disk recorder accepts alarm signals supplied
from connected devices such as sensors or camera site
equipment. The recorder itself also generates an alarm sig-
nal when the preset motion detection is activated. Any
alarm signal starts recording with the preset recording
mode, field rate, and picture quality specified in the REC
MODE menu described earlier. Alarm recording stops
when the preset time has elapsed, the alarm [RESET] but-
ton on the front panel is pressed, or the ALARM RESET IN
signal is supplied from the connected device. The recorder
outputs an alarm recovery signal from the rear panel. 
Alarm Buzzer (ALARM BUZZ)
Enables or disables buzzer beeping when an alarm oper-
ates.
1. Move the cursor to ALARM BUZZ with the [
D] or [C]
button.
2. Rotate the JogDial to select ON or OFF.
The default is ON.
ON:Buzzer beeps while alarm is active.
OFF:Buzzer does not beep.
Video Loss (VIDEO LOSS)
Enables or disables video loss detection.
1. Move the cursor to VIDEO LOSS with the [
D] or [C]
button.
2. Rotate the JogDial to select ON or OFF.
The default is ON.
ON:Enables the recorder to detect video loss.
OFF:Ignores video loss.
Monitor Mode (MONITOR MODE)
This setting specifies whether to allow the display to
change from the currently displayed picture to the alarmed
channel when an alarm operates.1. Move the cursor to MONITOR MODE with the [
D] or
[
C] button.
2. Select the parameter with the JogDial, and press the
JogDial.
The default is SPOT.
SPOT:Switches to the picture of the alarmed channel.
OFF:Retains the previous display mode.
Video Motion Detection
(VMD SETUP)
A VMD or Video Motion Detector senses changes in the
video signals within a preset area and supplies alarm out-
put. When a change is detected, the recorder starts record-
ing. The detection sensitivity and area are selected on this
menu.
1. Move the cursor to VMD SETUP
Owith the [D] or [C]
button, and press the JogDial. The VMD SETUP window
opens.
2. Move the cursor to the desired line.
3. Rotate the JogDial to select the desired parameter, and
press the JogDial. 
The default is OFF.
LOW:Low sensitivity
MID:Medium sensitivity
HIGH:High sensitivity
OFF:Motion detection is disabled.
The area setup window appears with an asterisk when
other than OFF is selected. The asterisk represents the
upper-left or bottom-right of the detection area. The
division lines are not actually displayed on the monitor.
      ALARM SETUP
ALARM BUZZ     ON
VIDEO LOSS     ON
MONITOR MODE   SPOT
VMD SETUPO
       VMD SETUP
CAM             SENS
  1              OFF
  2              LOWO
  3              MIDO
  4              HIGHO
  5              OFF
  6              OFF
  7              OFF
  8              OFF 
						

							36
Notes: 
•VMD should be used when the input to the unit is
from an ordinary camera. Select [OFF] to avoid use-
less VMD when a video multiplexer or combination
camera supplies the input to the unit.
•Set ALARM SUSPEND to ON when you do not want
VMD to be activated during the VMD setup.
•There may be cases where VMD does not suffi-
ciently detect changes, since it detects the
changes in luminance.
•The detection area may include areas slightly out-
side the border.
•The buzzer will beep if detection takes place during
the area setup.
4. Set the upper-left end of the detection area. Move the
asterisk to the right or left with the JogDial, and up or
down by pressing the [
D] or [C] button.
5. Press the JogDial to enter the upper-left end of the
detection area. The asterisk position is highlighted.
6. Set the bottom-right end of the detection area similar to
steps 3 and 4 above.
7. Press the JogDial. The area is highlighted.
Up to 4 areas can be selected. These may partially
overlap. Repeat steps 3 to 6 to select more areas. To
deselect an area, move the cursor to the upper-left end
of the area, and press the JogDial.
Communication Setup
(COMMUNICATION SETUP)
Communication parameters are set to match those of the
connected devices and the system configuration. The serial
port setup and network setup are made.
Serial Port Setup 
(SERIAL PORT SETUP)
The SERIAL PORT SETUP menu appears when it is select-
ed in the COMMUNICATION SETUP menu.
Note:Parameters marked with * on the following pages are
default settings applicable to RS-232C.
Protocol (PROTOCOL)
1. Move the cursor to PROTOCOL with the [D] or [C] but-
ton.
2. Select a suitable protocol with the JogDial, and press
the JogDial. 
The default is PS
•DATA.
PS•DATA:Select when the communication chain uses
the PS
•DATA protocol.
This selection enables the DATA terminal on the
rear panel for communication.
RS-232C:Select when a protocol other than PS•DATA
is used. 
This selection enables the RS-232C terminal on the
rear panel for communication.
Note:Parallel use of the DATA and RS-232C terminals
is not possible.
               *
CAM1
PUSH    PAUSE//SET
REW/FF/STEP/
q
w
e
r
   SERIAL PORT SETUP
PROTOCOL      PS•DATA
BAUD RATE     9600
DATA BIT      8
PARITY CHECK  NONE
STOP BIT      1
WAIT TIME     OFF
CTL-UNIT ADDR 1
SYS-UNIT ADDR 1
ALARM DATA    1S
CAM NO.SETUPO
  COMMUNICATION SETUP
SERIAL PORT SETUPO
NETWORK SETUPO 
						

							37
Baud Rate (BAUD RATE)
1. Move the cursor to BAUD RATE with the [D] or [C] but-
ton.
2. Select the rate with the JogDial, and press the JogDial. 
The default value is 9600 bits per second.
4800:4 800 bps
9600:9 600 bps*
19200:19 200 bps
Data Bit (DATA BIT)
1. Move the cursor to DATA BIT with the [D] or [C] but-
ton.
2. Select the bit length with the JogDial. 
The default value is 8 bits.
7:7 bits* ; select when using RS-232C protocol.
8:8 bits
Parity Check (PARITY CHECK)
1. Move the cursor to PARITY CHECK with the [D] or [C]
button.
2. Select the check mode with the JogDial. 
The default is NONE.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity*
Stop Bit (STOP BIT)
1. Move the cursor to STOP BIT with the [D] or [C] but-
ton.
2. Select the number of stop bits with the JogDial.
The default is 1.
1:1 bit*
2:2 bits
Wait Time (WAIT TIME)
The unit retransmits data after waiting the specified time if
there is no response from the connected device.
1. Move the cursor to WAIT TIME with the [
D] or [C] but-
ton.
2. Select the waiting time with the JogDial.
The default is OFF.
OFF:Retransmission is disabled. *
100MS:100 m seconds
200MS:200 m seconds
1S:1 second
Control Unit Address (CTL-UNIT
ADDRESS) (only for PS
•DATA)
When the recorder performs as a controller in the system,
the unit address can be set from the setup menu on the
monitor.
1. Move the cursor to CTL-UNIT ADDRESS with the [
D] or
[
C] button.
2. Select the address with the JogDial. 
The default value is 1.
Assignable address:From 1 to 99, must be unique in
the chain.
Note:Assign an address except 1 to WJ-HD200 when
using a system controller in the system.
System Unit Address (SYS-UNIT
ADDRESS) (exclusive to PS
•DATA)
When the recorder performs as a system unit, the unit
address can be set from the setup menu on the monitor.
1. Move the cursor to SYS-UNIT ADDRESS with the [
D] or
[
C] button.
2. Select the address with the JogDial.
The default value is 1.
Assignable address:From 1 to 99, must be unique in
the chain.
Alarm Data (ALARM DATA) (exclusive
to PS
•DATA)
The recorder pauses before sending a notice to the con-
nected system controller when an alarm operates.
1. Move the cursor to ALARM DATA with the [
D] or [C]
button.
2. Select the parameter with the JogDial, and press the
JogDial.
The default is 1S.
OFF:Select this when no system controller is connect-
ed.
0S:Does not pause.
1S:Pauses 1 second.
5S:Pauses 5 seconds. 
						

							38
Camera Number Setup (CAM NO.
SETUP) (exclusive to PS
•DATA)
Camera numbers will be used in a PS•DATA chain when
you select a camera to control it from a system controller.
1. Move the cursor to CAM NO. SETUP
Owith the [D] or
[
C] button, and press the JogDial. The CAM NO.
SETUP menu opens.
2. Move the cursor to the desired line with the [
D] or [C]
button.
3. Select the number with the JogDial, and press the
JogDial.
The default number is the same as the CAM-PORT
number.
Assignable numbers:From 001 to 128, each number
must be unique in the chain.
4. Press the [SETUP/ESC] button to go back to the SERI-
AL PORT SETUP.
Network Setup (NETWORK
SETUP)
Note:The system will restart after the menu setup window
is closed when any parameter in this window has been
changed.
Line Speed (LINE SPEED)
1. Move the cursor to LINE SPEED with the [D] or [C]
button.
2. Select the parameter with the JogDial, and press the
JogDial.
The default is AUTO.
AUTO:The speed is automatically selected.
100M_FULL:100 mega byte, full duplex
100M_HALF:100 mega byte, half duplex
10M_FULL:10 mega byte, full duplex
100M_HALF:10 mega byte, half duplex 
HTTP Port (HTTP PORT)
Set an HTTP port number.
The default is 80.
Available port numbers:From 00000 to 65535, except
the well-known port numbers assigned by IANA
(Internet Assigned Numbers Authority)
Dynamic Host Configuration Protocol
(DHCP)
Dynamic Host Configuration Protocol is enabled or dis-
abled.
The default is OFF.
Note:When ON is selected, you cannot enter the IP
address, netmask, or gateway. The host gives these
parameters.
The given parameters will be displayed after getting
the IP address from the DHCP server.
      CAM NO.SETUP
CAM-PORT        CAM NO.
   1               001
   2               002
   3               003
   4               004
   5               005
   6               006
   7               007
   8               008
     NETWORK SETUP
LINE SPEED AUTO
HTTP PORT
→   00080
DHCP       OFF
IP ADDR 
→192.168.000.010
NETMASK →255.255.255.000
GATEWAY →192.168.000.001 
						

							39
IP Address (IP ADDR)
The default is 192.168.000.010.
Netmask (NETMASK)
The default is 255.255.255.000.
Gateway (GATEWAY)
The default is 192.168.000.001.
Switcher Setup (SWITCHER
SETUP)
Video switcher functions are programmed in this menu
setup.
Start Display (START DISPLAY)
The image in the selected form will be displayed on the
monitor when the recorder is turned on.
Single image:CH 1 to CH 8
Quad image:QUAD-4A (including 1-4), QUAD-4B
(including 5-8)
Multi image:9SCREEN (including 1-8)
Sequence:SPOT SEQ, MULTI SEQ
Multiscreen Selection (MULTI SEL
MODE)
When pressing the [MULTI SCREEN SEL] button on the
front panel, the monitor display will change as follows
depending on the setup.
QUAD ONLY:QUAD-4A →QUAD-4B →QUAD-4A
ALL:QUAD-4A →QUAD-4B →9SCREEN →QUAD-4A 
Sequence Setup (SEQUENCE
SETUP)
1. Move the cursor to SEQ SETUP in the SWITCHER
SETUP menu, and press the JogDial.
The SEQUENCE SETUP menu opens.
2. Select either MULTI SEQ SETUP or SPOT SEQ SETUP
with the [
D] or [C] button, and press the JogDial. The
selected menu opens.
Multiscreen Sequence Setup (MULTI
SEQ SETUP)
Open the QUAD SEQ SETUP menu to program the
sequence steps for displaying quad-split and single input
images.
1. Move the cursor to the desired step using the [
D] or
[
C] button.
2. Select a camera number with the JogDial, and press
the JogDial.
The default camera number is identical to the step num-
ber.
Available cameras:From 1 to 8 individually, 4A(1-4), or
4B(5-8)
Note:The recorder will skip any step assigned –.
3. Select the duration for the step with the JogDial, and
press the JogDial.
Available durations:2-30S
     SWITCHER SETUP
START DISPLAY  QUAD-4A
MULTI SEL MODE ALL 
SEQUENCE SETUPO
CAMERA VIEW SETUPO
     SEQUENCE SETUP
MULTI SEQ SETUPO
 SEQUENCE TIMING  INT
 AUTO SKIP        ON
SPOT SEQ SETUPO
 SEQUENCE TIMING  INT
 AUTO SKIP        ON
    MULTI SEQ SETUP
STEP     CAM      SEC
   1 
→ QUAD-4A     2S
   2 → QUAD-4B     2S
   3 →    -        2S
   4 →    -        2S
   5 →    -        2S
   6 →    -        2S
   7 →    -        2S
   8 →    -        2S 
						

							40
4. Repeat steps 1, 2, and 3 until all steps are pro-
grammed, or press the [SETUP/ESC] button to return to
the SEQUENCE SETUP menu.
5. Move the cursor to SEQUENCE TIMING in the SEQ
SETUP menu.
Select INT or EXT with the JogDial, and press the
JogDial.
The default is INT.
INT:Forwards the step when the assigned time elaps-
es.
EXT:Forwards the step when the SEQ IN signal is input
to the rear panel.
6. Move the cursor to AUTO SKIP with the [
D] or [C] but-
ton.
Select ON or OFF with the JogDial, and press the
JogDial.
The default is ON.
ON:The sequence skips any step where no video is
input.
OFF:The step will be displayed as a blackout screen.
Spot Sequence Setup (SPOT SEQ
SETUP)
Open the SPOT SEQ SETUP menu to program the
sequence steps for displaying single input images.
1. Move the cursor to the desired step using the [
D] or
[
C] button.
2. Select a camera number with the JogDial, and press
the JogDial.
The default camera number is identical to the step num-
ber.
Available cameras:From 1 to 8.
Note:The recorder will skip any step assigned –.
3. Select the duration for the step with the JogDial, and
press the JogDial.
Available durations:2-30S4. Repeat steps 1, 2, and 3 until all steps are pro-
grammed, or press the [SETUP/ESC] button to return to
the SEQUENCE SETUP menu.
5. Procedures for SEQUENCE TIMING are the same as
step 5 in MULTI SEQ SETUP.
6. Procedures for AUTO SKIP are the same as in step 6 of
MULTI SEQ SETUP.
Camera View Setup (CAMERA VIEW
SETUP)
Open the CAMERA VIEW SETUP menu to program the live
image of each camera channel to be displayed or vailed on
the monitor.
1. Move the cursor to the desired camera using the [
D] or
[
C] button.
2. Select ON or OFF with the JogDial, and press the
JogDial.
The default is ON.
ON:Live image of the channel is displayed.
OFF:Blackout image is displayed.
3. Repeat steps 1 and 2 until all channels are pro-
grammed, or press the [SETUP/ESC] button to return to
the SWITCHER SETUP menu,
Notes: 
• Recording will be carried out regardless of this set-
ting.
• The recorded images of the channel will be played
back and displayed on the monitor even if OFF is
selected.
SPOT SEQ SETUP
STEP CAM SEC
1
→12S
2→22S
3→32S
4→42S
5→52S
6→62S
7→72S
8→82S
CAMERA VIEW SETUP
CAM MODE
1ON
2ON
3ON
4ON
5 OFF
6 OFF
7 OFF
8 OFF