Panasonic Digital Disk Recorder Wj Hd200 Operating Instructions

							21
SETUP PROCEDURES
Prior to Setup
Turning On the Power
1. Plug the power cord into the AC outlet.
2. Turn on the power switch on the rear panel. The oper-
ate LED lights up. An HDD check and a system check
will be carried out while displaying respective mes-
sages.
Power-on recording will start if TIMER has been set to
EXT in the SYSTEM SETUP menu.
3. Press the [REC STOP] button to stop power-on record-
ing, if applicable.
4. Hold down the buttons of [LOCK] and [RESET] simulta-
neously to suspend alarm inputs. The SUSPEND indica-
tor will light up. This will prevent your setting operations
from being interrupted by alarm inputs.
Note:Refer to Power-on Procedures in the Appendix
for details.
Turning Off the Power
1. Press the [STOP] button when playing back, or [REC
STOP] button when recording. Confirm that the HDD
access indicator has turned off.
2. Turn off the power switch on the rear panel. The oper-
ate LED goes off.
Notes:
•Do not turn off the power while the HDD access
indicator is on.
•Do not leave the recorder turned off for a long time.
Supply AC power to the unit and turn it on to charge
up the backup battery.
Confirm that
the HDD access 
indicator is off.
SIGNAL GND
POWER
OFFON
HDD
FULLERRORALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESCPLAY
TIME&DATE
SEARCH
REC STOP
ALARM
RECALL
RECPUSH–    PAUSESET
Digital Disk Recorder WJ-HD200
HDD
FULLERRORALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESCPLAY
TIME&DATE
SEARCH
REC STOP
ALRE
REC
SIGNAL GND
POWER
OFFONOPERATEALARM
SUSPEND
RESET
OPERATEALARM
SUSPEND
RESETOSD
TIMERDSTREMOTE
LOCKSEQUE
SPMU 
						

							22
Displaying WJ-HD200 (MAIN MENU)
1. Confirm that the camera and peripherals are connected
correctly and securely.
2. Turn on the power switches of all system components.
3. Hold down the [STOP] button for 2 seconds. The WJ-
HD200 MAIN MENU appears.
Buttons and Dials Used for Setup
[Dup] button:Moves the cursor upwards in a menu, and
opens the previous menu page.
[Cdown] button:Moves the cursor downwards in a menu,
and opens the next menu page.
JogDial (Counter-clockwise):Decreases the parameter
value.
JogDial (Clockwise):Increases the parameter value.
JogDial (Pressing) SET:Validates the selection, and
moves the cursor to the right. When the selected item
has a 
Oreturn symbol, pressing this will open the next
lower layer menu for more minute settings
[STOP SETUP/ESC] button (Pressing):Moves the cursor
to the left, or returns to the previous menu.
[STOP SETUP/ESC] button (Holding down):Opens the
setup menu, or escapes from it and switches back to
normal operation.
   WJ-HD200 MAIN MENU
TIMER            OFFO
REC SETUPO
EXT REC SETUPO
DISPLAY SETUPO 
SYSTEM SETUPO 
ALARM SETUPO 
COMMUNICATION SETUPO 
SWITCHER SETUPO 
SYSTEM INFORMATIONO 
HDD
FULL
ERROR
NALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESCPLAY
TIME&DATE
SEARCH
REC STOP
ALARM
RECALL
RECPUSH—    PAUSESET
Digital Disk Recorder WJ-HD200
Closing WJ-HD200 (MAIN MENU)
1. Hold down the [STOP SETUP/ESC] button for 2 sec-
onds. 
The setup menu disappears, and normal operation will
be available.
Note: A blackout screen may appear for about 2 sec-
onds until the camera image is displayed if you
changed the settings and closed the setup menu. 
						

							23
Menu Tree
The figure shows the hierarchy of menu windows.
WJ-HD200
MAIN 
MENU
TIME
ADJUST
SETUP
VMD
SETUP
SERIAL 
SETUP
SEQUENCE
SETUP
CAMERA 
VIEW
SETUP
SYSTEM
LOGCAM NO.
SETUP
VMD
AREA
SETUP
MULTI
SEQ
SETUP
SPOT
SEQ
SETUP SYSTEM
SETUP
CAMERA 
TITLE DISPLAY
SETUP
EXT REC
SETUP
REC
SETUP
TIMER
REC
(Assignment)PROG1 SETUP
(Time Zone)
PROG2 SETUP
 (Time Zone)
TRIGGER
ACTION
SETUP
1 - 1
CAM REC
SETUP
1 - 1
PROG1 NO. 1
PROG1 NO. 4
NO. 1 - NO. 4 (Same as PROG1)
PROG3 SETUP
(Time Zone)NO. 1 - NO. 4 (Same as PROG1)
PROG4 SETUP
 (Time Zone)NO. 1 - NO. 4 (Same as PROG1) TIMER
INT
ALARM
SETUP
COMMUNI-
CATION
SETUP
NETWORK
SETUP
SWITCHER
SETUP
SYSTEM
INFORMATION
~ ~
TRIGGER
ACTION
1 - 4
CAM REC
SETUP
1 - 4
TRIGGER
ACTION
1 - 4
CAM REC
SETUP
1 - 4
TIMER
OFF
TIMER
EXT 
						

							24
Initializing
You can initialize all disk contents including image data
and/or setup data.
Initializing All Contents & Setup Data
Warning!The following are irrevocable procedures. We
strongly recommend that you copy important pic-
tures from the hard disk.
1. Press the [REC STOP] button or [STOP] button to stop
recording or playback.
2. Turn off the power.
3. Set MODE switches #1 through 4 on the rear panel as
follows:
#1:ON
#2:OFF
#3:OFF
#4:ON
4. Turn on the power.
The disk contents and setup data are initialized.
Notes:
•This will take about 40 minutes.
•When finished, be sure to carry out step 5.
5. Turn off the power, and return the MODE switches to
the previous positions. Then turn on the recorder.
Initializing Setup Data
1. Open the SYSTEM INFORMATION window, then move
the cursor to DEFAULT.
2. Press the JogDial to move the cursor to SET.
3. Press the JogDial.
4. Select YES with the JogDial.
YES:Initializing of setup data is enabled.
5. Press the JogDial.
SET DONE appears on the monitor after initializing.
6. Press the [SETUP/ESC] button.
The cursor moves to DEFAULT.
7. Hold down the [SETUP/ESC] button for 2 seconds to
quit the setup.
Notes:
•After closing the setup menu, the system may auto-
matically restart if any parameter on the network
has been changed.
•The menu shown above is based on the assumption
that an optional HDD is installed in the recorder. As
shipped from the factory, the hour meter is set to 1
and the capacity to half.
Initializing Settings for Network
Setup Menu
1. Stop recording or playback if
applicable, and turn off the
power.
2. Set the MODE switches as
shown in the figure.
3. Turn on the power. Wait for a few minutes until  initializ-
ing is completed.
4. Return the MODE switches to the previous positions.
Then press the [STOP] button.
Note:These procedures reset the settings exclusively
for network setup menus: USER SETUP, HOST
SETUP, FTP SETUP, MAIL SETUP, and NETWORK
VIDEO SETUP.
MODE
ON
ON
OFF
123456
     
   
NOW FORMATTING HDD
     
FORMAT FINISHED
 PLEASE TURN OFF MODE
 SW AND RESTART
   SYSTEM INFORMATION
HDD1 HOUR METER  10000H
HDD2 HOUR METER  10000H
HDD CAPACITY    228.99G
DEFAULT
→        SET→
SYSTEM VERSION  X.XX
SYSTEM LOGO
MODE
123456
ON 
						

							25
Main Menu (WJ-HD200 MAIN
MENU)
The main menu is located at the top of the menu tree from
where every menu window starts.
1. Hold down the [SETUP/ESC] button for 2 seconds. The
main menu appears.
2. Select a setup menu you wish to program using the [
D]
or [
C] button, and press the [SET] (JogDial).
The selected setup menu opens. The following pages
will detail each setup menu.
Timer Recording Setup (TIMER
REC)
This menu assigns a timer to start recording by use of an
external timer or the internal timer. When the internal timer
(INT) is set, there are four programs assignable to the
weekly and/or daily schedule. Each program can contain
up to four events along with start and end time, and record-
ing-mode. Alarm recording will be carried out when an
alarm operates within the scheduled time zone.
When the external timer (EXT) is set and the connected
timer switch turns on to supply power, the recorder will start
power-on recording.
1. Select a timer mode using the JogDial.
OFF:Does not use any timer, and manual recording is
available.
INT:Carries out internal timer recording according to
the program.
EXT:Carries out power-on recording.
2. Press the JogDial to validate the selection. When INT is
selected, the TIMER REC menu opens.3. Move the cursor to the desired line using the [
D] or 
[
C] button.
4. Select any parameter from PROG1 to PROG4 using the
JogDial, and press the JogDial. The PROG1-4 SETUP
menu opens.
Program 1-4 Setup (PROG1-4
SETUP)
1. Select the event number with the [D] or [C] button,
and press the JogDial. The cursor moves to the START
position. 
After this operation, the [
D] and [C] buttons move the
cursor to the right and left.
2. Select a start time (START) using the JogDIal, and
press the [
D] button to move to the next position.
Available START times:From 0:00 to 23:59 in the 24-
hour system.
3. Select an end time (END) in the same way as above
and press the [
D] button to move the cursor to the
MODE position.
Available END times:From 0:01 to 24:00 in the 24-
hour system.
Notes:There are some restrictions on programming.
•An event, except the first event (NO 1), can be pro-
grammed only if the immediately preceding event
has been set up.
•The start time should be later than the end time of
the immediately preceding event. 
•The end time should be later than the start time of
the event.
•An end time set at 24:00 will cancel all following
events.
4. Press the JogDial while the cursor is on SET
Oto open
the event programming menu.
   WJ-HD200 MAIN MENU
TIMER            OFFO
REC SETUPO
EXT REC SETUPO
DISPLAY SETUPO 
SYSTEM SETUPO 
ALARM SETUPO 
COMMUNICATION SETUPO 
SWITCHER SETUPO 
SYSTEM INFORMATIONO 
      PROG1 SETUP      
NO. START END   MODE
1
→  8:00 12:20  SETO
2
→ 13:00 15:00  SETO
3
→   :     :
4
→   :     :
       TIMER REC
             PROGRAM
SUNDAY        PROG1O
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
DAILY 
						

							26
Recording Mode Setup (PROG1-4
SETUP, NO. 1-4)
Parameters for internal timer recording are assigned to
each event (NO. 1-4) of the program (PROG 1-4) in this
menu. There are five recording modes available: super fine
(SF), fine (FQ), normal (NQ), long-time (EX) and optional
(SP). If combined with audio recording (-A), the number of
recording modes doubles. The selected recording mode
determines the remaining recording time displayed on the
monitor.
In the SP mode, the field rate and picture quality are vari-
able and can be selected at option in the range of 0.1 to 30
FPS with five quality level options respectively. After the
recording mode is selected, the available recording time is
determined and displayed.
Notes: 
•For the recording modes other than SP, items suf-
fixed xxx in the table will be replaced by a calcu-
lated recording time of 24, 48, 72, 96, 120, 170,
180, 240, 480, 960, 1 200, 1 440, 2 160, 2 880, or 
8 640 hours. The selected recording mode with the
preset rate and quality will determine the suffix.
•Even if preset to 30 or 15 FPS, the actual recording
rate may drop to 7.5 FPS at worst while busy multi-
tasks task such as playback, remote-access play-
back, remote-access live image, FTP access, multi-
split display, or video motion detection are carried
out simultaneously. The status display will indicate
*PLAY while playing back the images recorded
with a rate different from the preset.
•Suffix xxx following SP- is specified in REC
MODE TABLE in the ADDENDUM attached to the
manual.
1. Move the cursor to MODE, and press the JogDial. The
mode area will be highlighted.
2. Select a recording mode using the JogDial, and press
the Jogdial. Audio data will be recorded when a mode
with hyphen A is selected.
Available recording mode:SF, FQ, NQ, EX, SP, SF-A,
FQ-A, NQ-A, EX-A, and SP-A
N/A
Rec Mode Quality Audio Record Note
SF-xxxH Super Fine N/A
Field rate, quality
selected optionally Field rate, quality
selected optionally N/A
N/A
N/A
Available
Available
Available
Available Fine
Normal
Long time
Optional setup Super Fine
Fine
Normal
Long time FQ-xxxH
NQ-xxxH
EX-xxxH
SP-xxxHAvailable Optional setup SP-AxxxH SF-AxxxH
FQ-AxxxH
NQ-AxxxH
EX-AxxxH
3. When SP or SP-A is selected, specify a recording rate
(REC RATE) using the JogDial, and press the JogDial.
Available recording rates:From 0.1 to 30 FPS
4. When SP or SP-A is selected, specify a recording quali-
ty (REC QUALITY) using the JogDial, and press the
JogDial.
Available recording qualities:SUPER FINE, FINE,
NORMAL, EXTENDED
Alarm Recording Mode Setup (ALM
REC MODE)
Alarm events arising within the time zone specified by the
program will start recording with the preset parameters.
Refer to PROG NO. SETUP described above in this menu
for operating procedures and available parameters, since
they are very similar.
Pre-alarm Recording (PRE ALM REC)
Picture recording will start prior to the alarm activation at
the time specified by this setting.
1. Move the cursor to PRE ALARM REC with the [
D] or
[
C] button.
2. Select the desired pre-recording time with the JogDial,
and press the JogDial.
The default is 0S.
Available times (seconds):0S, 1S, 2S, 3S, 4S, and 5S 
						

							27
Post-alarm Recording (POST ALM
REC)
This setting specifies the duration of alarm recording after
an alarm input. Functions active during alarm recording are
buzzer beeping, ALARM LED indication, ALARM status
display, and the ALARM OUT signal.
1. Move the cursor to POST ALARM REC with the [
D] or
[
C] button.
2. Select the desired duration with the JogDial.
The default value is 10 seconds.
The unit will revert to the previous status when the time
has elapsed.
Available times (seconds): 5, 10, 20, 30
Available times (minutes):1, 1.5, 2, 3, 6
Continue: Recording continues until the [REC STOP]
button is pressed, or the RESET IN signal is sup-
plied to the rear panel.
Manual: Recording continues for as long as the alarm
input is active, or at least for 10 seconds if the input
turns inactive earlier.
Dynamic Recording (DYNAMIC REC)
This setting specifies the recording pattern on the disk
when one or more alarms operate.
1. Move the cursor to DYNAMIC REC with the [
D] or [C]
button.
2. Select the parameter with the JogDial, and press the
JoDdial.
The default is OFF.
ALM-MULTI:Alarmed channels are recorded with pri-
ority over others.
OFF:All channels are recorded with the same priority.
Trigger Action Setup (TRIGGER
ACTION SETUP)
This setting specifies the two roles of alarm recording and
alarm control functions (Refer to page 44) in the post-alarm
sequence.1. Move the cursor to TRIGGER ACTION SETUP
O, and
press the JogDial.
The TRIGGER ACTION SETUP menu opens.
2. Move the cursor to the channel.
3. Select the parameter with the JogDial, and press the
JogDial.
The default is REC&ALM.
OFF:Disables alarm recording or warning.
REC&ALM:Enables both alarm recording and warning.
REC:Enables alarm recording, but disables warning.
4. Repeat steps 2 and 3 until all channels are set.
5. Press the [SETUP/ESC] button to return to the PROG1
SETUP, NO. 1 menu.
Camera Recording Setup (CAM REC
SETUP)
This setting is provided for the purpose of saving disk
space. Setting allows each camera channel to be enrolled
in all recording modes or exclusively in alarm recording.
1. Move the cursor to CAM REC SETUP, and press the
[SET] button. The CAM REC SETUP menu opens.
2. Move the cursor to the camera channel with the [
D] or
[
C] button.
3. Select the parameter with the JogDial, and press the
JogDial.
The default is REC.
REC:The channel is recorded in alarm recording, timer
recording and manual recording mode.
ALM-ONLY:The channel is recorded only when the
alarm operates.
4. Repeat steps 2 and 3 until all channels are set.
5. Press the [SETUP/ESC] button to return to the PROG1
SETUP, NO. 1 menu.
      CAM REC SETUP
CAM           MODE
  1           REC
  2           REC
  3           REC
  4           ALM-ONLY
  5           REC
  6           ALM-ONLY
  7           REC
  8           REC
  TRIGGER ACTION SETUP
CAM              MODE
  1              OFF
  2              OFF
  3              OFF
  4              REC&ALM
  5              REC
  6              OFF
  7              OFF
  8              OFF 
						

							28
Manual Recording Setup (REC
SETUP)
The WJ-HD200 will record image and audio data either with
or without timer restrictions. Manual recording is available
when OFF is selected for TIMER in WJ-HD200 MAIN MENU;
the timer schedule does not apply. Alarm recording will
also be carried out with parameters specified in this menu.
Refer to 
Recording Mode Setup PROG1-4 SETUP, NO. 1-
4 for operating procedures and available parameters.
Externally Specified Recording
Mode (EXT REC SETUP)
This setting allows changing the recording mode from the
ongoing one to an optional one specified here when turning
on the switch connected externally to the EXT REC terminal.
1. Move the cursor to EXT REC MODE with the [
D] or [C]
button.
2. Select the desired mode with the JogDial, and press
the JogDial.
Refer to page 26 and 27 for the recording mode para-
meters.
3. Press the [SETUP/ESC] button to return to WJ-HD200
MAIN MENU.
Display Setup (DISPLAY SETUP)
You can program the display of information on the monitor,
such as clock, time and date, and so forth.
Clock (CLOCK)
1. Press the JogDial (SET) to move the cursor to the
desired position.
2. Rotate the JogDial clockwise to increase the parameter,
or counter-clockwise to decrease. The positions indi-
cate the year, month, day, hour, and minute respective-
ly.
The default is JAN 01. 03 00:00.
MM DD YY HH : MM
3. Press the JogDial (SET) to validate the selection.
4. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Time & Date (TIME&DATE)
1. Select a display type with the JogDial.
The default is TYPE1 24H.
TYPE1 24H:Time and date are displayed in one line in
the 24-hour system.
TYPE1 12H:Time and date are displayed in one line in
the AM-PM system.
TYPE2 24H:Time and date are displayed in two lines in
the 24-hour system.
TYPE2 12H:Time and date are displayed in two lines in
the AM-PM system.
     DISPLAY SETUP
CLOCK
→ JUN30.03  15:05
TIME&DATE      TYPE1 24H
TIME&DATE DISP.ON
TIME&DATE POSI.R-LOWER
STATUS DISP.   ON
STATUS POSI.   R-LOWER
HDD FULL        1%
REMOTE LED     ON
HDD CHECK       0:00
CAMERA TITLEO 
JUN30.03  20:00:00
JUN30.03
20:00:00
TYPE1
TYPE2
   WJ-HD200 MAIN MENU
TIMER            OFFO
REC SETUPO
EXT REC SETUPO
DISPLAY SETUPO 
SYSTEM SETUPO 
ALARM SETUPO 
COMMUNICATION SETUPO 
SWITCHER SETUPO 
SYSTEM INFORMATIONO  
						

							29
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Time & Date Display (TIME&DATE
DISP.)
1. Select ON or OFF with the JogDial.
The default is ON.
ON:Time & date display is enabled. 
OFF:Time & date display is disabled.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Time & Date Position (TIME&DATE
POSI.)
1. Select a display position with the JogDial.
The default is R-LOWER.
R-LOWER:Displays time & date in the lower right cor-
ner.
R-UPPER:Displays time & date in the upper right cor-
ner.
L-LOWER:Displays time & date in the lower left corner.
L-UPPER:Displays time & date in the upper left corner.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Note:When the 9-split screen is displayed, the time and
date position is fixed to R-LOWER. 
JUN30.03 20:00:00JUN30.03 20:00:00
JUN30.03 20:00:00JUN30.03 20:00:00
L-UPPER
L-LOWERR-UPPER
R-LOWER
Status Display (STATUS DISP.)
1. Select ON or OFF with the JogDial.
The default is ON.
ON:Status display is enabled.
OFF:Status display is disabled.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Status Position (STATUS POSI.)
1. Select a display position with the JogDial.
The default is R-LOWER.
R-LOWER:Displays status in the lower right corner.
R-UPPER:Displays status in the upper right corner.
L-LOWER:Displays status in the lower left corner
L-UPPER:Displays status in the upper left corner.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Note:When the 9-split screen is displayed, the status posi-
tion is fixed to R-LOWER. 
PLAYPLAY
PLAYPLAY
L-UPPER
L-LOWERR-UPPER
R-LOWER 
						

							2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Disk Check (HDD CHECK)
S.M.A.R.T. (Self-Monitoring Analysis and Reporting
Technology) is activated or deactivated for HDD check.
1. Select either ON or OFF with the JogDial.
The default is OFF.
ON 0:00-23:00:The recorder checks the HDD at the
specified time every day.
OFF:Check is deactivated.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Note:Recording will resume after a one-second inter-
mission when HDD is checked.
Camera Title (CAMERA TITLE)
Camera title and display position are specified for each
camera.
1. In the DISPLAY SETUP menu, move the cursor to CAM-
ERA TITLE
O, and press the JogDial to open the CAM-
ERA TITLE menu.
2. Move the cursor to the camera you wish to program
using the [
D] or [C] button.
30
Disk Capacity Warning (HDD FULL)
The recorder monitors the disk capacity to warn the opera-
tor that the available capacity is nearing its end when STOP
is selected for DISK END MODE. There are two warning
levels. First, the FULL indicator on the front panel blinks
when the remaining capacity has reached the preset value.
Finally, the buzzer beeps when the disk is full, provided that
the DISK END BUZZER parameter in the SYSTEM SETUP is
set to ON. At the same time, the FULL indicator turns on.
1. Select the desired value with the JogDial.
The default is 1 %.
1% - 99%:The FULL indicator blinks when the remain-
ing capacity reaches the selected value.
2. Press the JogDial (SET) to validate the selection.
3. Press the [
D] or [C] button to select the next item, or
press the [SETUP/ESC] button to quit the display setup.
Remote LED (REMOTE LED)
The remote LED on the front panel will indicate or ignore
the remote controlled status of the recorder via the network.
1. Select either ON or OFF with the JogDial.
The default is OFF.
ON:REMOTE LED turns on when the network controls
the recorder. 
OFF: REMOTE LED is deactivated.
     DISPLAY SETUP
CLOCK
→ JUN30.03  15:05
TIME&DATE      TYPE1 24H
TIME&DATE DISP.ON
TIME&DATE POSI.R-LOWER
STATUS DISP.   ON
STATUS POSI.   R-LOWER
HDD FULL        1%
REMOTE LED     ON
HDD CHECK       0:00
CAMERA TITLEO 
     DISPLAY SETUP
CLOCK
→ JUN30.03  15:05
TIME&DATE      TYPE1 24H
TIME&DATE DISP.ON
TIME&DATE POSI.R-LOWER
STATUS DISP.   ON
STATUS POSI.   R-LOWER
HDD FULL        1%
REMOTE LED     ON
HDD CHECK       0:00
CAMERA TITLEO 
CAMERA TITLE
CAM TITLE POSI.
1 OFF
2ON
→2¥¥¥¥ R-LOWER
3ON→3¥¥¥¥ L-LOWER
4 OFF
5 OFF
6 OFF
7 OFF
8 OFF
     DISPLAY SETUP
CLOCK
→ JUN30.03  15:05
TIME&DATE      TYPE1 24H
TIME&DATE DISP.ON
TIME&DATE POSI.R-LOWER
STATUS DISP.   ON
STATUS POSI.   R-LOWER
HDD FULL        1%
REMOTE LED     ON
HDD CHECK       0:00
CAMERA TITLEO