Panasonic Digital Disk Recorder Wj Hd200 Operating Instructions

WJ-HD200
81
Daylight saving
OFF, INT or EXT selectable Item WV-CU360 NoteDST
SHIFT
SETUP
FUNCTION3 1
Timer REC mode
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION9 1
Button lock off
Enter your password.
Button lock on
SHIFT
SETUP
FUNCTION31
SHIFT
SETUP
FUNCTION30
Statusd display on/offOSD
LOCK
Time and date searchTIME&DATE
SEARCH
SHIFT
SETUP
FUNCTION0
Multiscreen pattern 
selection
Multiscreen monitorMULTISCREEN
SELECT
ZOOM
MULTI SCREEN SELECT
SPOT
MULTI
MON
ESC
Spot monitor
SPOT
MULTI
MON
ESC
Camera...

82
RS-232C Communication Protocol
The following pages detail the elements for communication between the Digital Disk Recorder and the personal computer. Be
sure to select RS-232C for PROTOCOL in the COMMUNICATION SETUP window. For BAUD RATE, DATA BIT and PARITY set-
tings, refer to COMMUNICATION SETUP. For cable connection refer to RS-232C CONNECTION.
1. Transmission Command
The PC sends messages to the Recorder in the format shown below. Also refer to the command table shown later.
[p] stands for...

83
Command Table
Basic Operation
Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII)
Fast Forward to the end OFF OFF
Pause OPA OPA
Play OPL OPL
Recording ORC ORC
Rewind to the top ORW ORW
Skip&Play Forward OSF:n OSF n=0F Normal speed
n=1F x2 speed
n=2F x5 speed
n=3F x50 speed
n=5F x100 speed
n=0S Normal speed
n=1S 1/2 speed
n=+ Increment
n=– Decrement
Stop OSP:n OSP n=P stops PLAY
n=R stops REC
no parameter stops PLAY and REC
Skip&Play Rewind OSR:n OSR Refer to OSF.
Forward a field OVF...

84
Setup Control
Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII)
Cursor Moves DCR:n1n2 DCR n1=A Right
n1=C Upward
n1=E Left
n1=G Downward
n2=1 Move a step
n2=2 Move multi steps
n1n2=PD Move to lower layer
n1n2=P+ Move to upper layer
n1n2=P- Turn a newer page
n1n2=PU Turn an older page
Key Lock MKL:n MKL n=0 Lock OFF
n=1 Lock ON
Recording Event  MRM:n MRM n=0 Normal recording
Setupn=1 Internal timer recording
n=2 External timer recording
Summer Time Setup MST:n MST n=0 Standard time...

85
Inquiry
Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII)
Remaining Size  QHR QHR:nnn nnn=000-100 Decimal %
Inquiry
ID Inquiry QID QID:WJ-HD200
Key Lock Status  QKM QKM:n n=0 Lock OFF
Inquiryn=1 Lock ON
Alarm Info Inquiry QLD:n QLD:n (Alarm Information)
In Transmission command:n=0 Event report
n=1 Date&time report
In Response command:n=0 No alarm event
n=1 Alarm has been reset
n=2 Alarm activated
k=0 VMD
n=2 PC alarm
Alarm...

86
HDD Maintenance
When to Maintain HDD
HDD maintenance is required in the following cases.
•When FULL indicator lights up
•When ERROR indicator lights up
•When an optional hard disk is added
•When you wish to format the HDD or to remove link
•When HDD reaches its life time (around 30 000 hours,
displayed in the SYSTEM INFO window)
 2 seconds later
       DISK MENU
NO.1:117.95GB
NO.2:117.95GB
REMOVE LINK
→   SET→HDD FORMAT →   SET→RESTART    →   SET→
SYSTEM CHECK
     
NO DISK
SYSTEM CHECK DONE!
TO...

87
When Error Indicator is Lit
Refer to your dealer for servicing when this happens.
8HDD Check
The recorder checks the hard disk when the recorder is
turned on, or when the HDD CHECK time specified in
the menu setup comes during operation. 
The recorder warns you of any error detected as fol-
lows.
Error indicator blinks.
Warning Out terminal on the rear panel turns active.
NO DISK will appear when there is no disk installed in the
recorder.
When this happens, turn off the power. New disk(s) should
be...

88
You can implement any of the following operations as necessary.
REMOVE LINK: Logically removes the HDD link.
HDD FORMAT: Formats the HDD.
RESTART: Closes the menu, and restarts the recorder.
The menu can also be displayed manually when you need to format the HDD or remove the logical link.
1. Turn off the power of the recorder once, and turn it on again. 
The multiscreen monitor displays the message SYSTEM CHECK DONE! TO OPEN DISK MENU, PUSH STOP KEY.
2. Press the [STOP] button.
The DISK MENU opens....

89
8Formatting HDD (HDD FORMAT)
This command initializes the HDD format and is applic-
able to HDDs of *, ERR, or ADD status.
Caution:Formatting is an irreversible procedure. We
strongly recommend that, before formatting, you
either save the recorded data into the server via the
network, or you save the data on VCR tapes via the
REC OUT terminal.
1. Display the DISK MENU window.
2. Move the cursor to HDD FORMAT, and press the
JogDial.
The password prompt appears.
3. Enter the ALL password using the CAM...

90
5. Select YES or NO rotating the JogDial, and press the
JogDial.
YES: Carries out formatting. Wait until the process
ends.
When 
YESis selected, the display will turn to NOW
FORMATTING. It will change to HDD FORMAT 
→SET
DONE when formatting is completed.
When the [STOP] button is pressed, the window returns
to that of step 1.
Select RESTART to return to normal operation.
8Restarting (RESTART)
This command closes the DISK MENU, and returns to
normal operation.
1. Display the DISK MENU.
2. Move the...