Panasonic Digital Color Imaging Systems For Copier Dp C266 Operating Instructions

							61
 Chapter 2    More Menus Features
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Sort / Finish”, and then select 
a sort mode.
‰When optional Finisher is not installed
‰When the optional 1Bin Saddle-Stitch 
Finisher is installed
z“Punch” function is only available when the 
optional Punch Unit is installed to the 1Bin 
Saddle-Stitch Finisher.
zWhen “Staple-Sort” or “Punch” is selected, 
refer to the following.Select the Orientation of the original, and then 
select the Staple position.
Select the Punch position.
Select for the original in portrait 
orientation. 
Select for the original in landscape 
orientation.
2 positions on the left side
1 position on the upper left side
2 positions on the upper side
2 positions on the right side
1 position on the upper right side
Continued on the next page... 
						

							62
 Chapter 2    More Menus Features
‰When the optional 1Bin Finisher is 
installed
zWhen “Staple-Sort” is selected, refer to the 
following.
Select the Orientation of the original, and then 
the Staple position.
5Enter the desired number of copies.
6Press the Start key.
zWhen copying from the Platen Glass, place 
the next original and follow the instructions 
described on the Touch Panel Display.
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode.
1 position on the upper left 
side
1 position on the upper 
right side 
						

							63
 Chapter 2    More Menus Features
Memo 
						

							64
 Chapter 2    More Menus Features
Zoom Mode
Variable Ratios
The original can be copied by setting the Enlargement/Reduction Ratio.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Zoom / Effects”, and then 
select “Zoom”.
5Select the item to enlarge/reduce.
When a reduction copy is selected, it is printed 
on the following position and size. 
XYSelect to set the same enlargement/
reduction ratio vertically and 
horizontally.
XSelect to set the horizontal 
enlargement/reduction ratio.
YSelect to set the vertical enlargement/
reduction ratio.
ABC 100%
ABCEx. 50%
Ex.25% ABC
Place original(s) on the ADF.
ABC 100%
ABCEx. 50%
Ex.25% ABC
Place an original on the Platen Glass. 
						

							65
 Chapter 2    More Menus Features
6Enter the zoom ratio with “S” and “T”, 
or the Keypad, and then select “OK”.
zThe ratio can be set in 1% increments from 
25% to 400%.
zWhen changing the paper size after setting 
the zoom ratio, select “Basic Menu”, and 
select “Paper/Output Tray”, and then select 
the paper size.
7Enter the desired number of copies.
8Press the Start key.
zWhen copying from the Platen Glass, place 
the next original, and follow the instructions 
described on the Touch Panel Display.
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode. 
						

							66
 Chapter 2    More Menus Features
Auto Zoom
By setting Auto Zoom, originals can be automatically enlarged/reduced to fit the size of the loaded 
paper.
zThis function can be selected when the original is placed on the Platen Glass.
zAs the original is placed on the Platen Glass, the position of the original may be erroneously detected if 
influenced by ambient light.
zIf the margin around the original is 5 mm wide or less, the original may not be correctly detected, and the copy 
image may be unclear.
1Open the ADF more than 45 degrees, 
and place original on the Platen Glass, 
and then leave the ADF open.
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Zoom / Effects”, and then 
select “Auto Zoom”.
Face down. Align with top left 
corner. 
						

							67
 Chapter 2    More Menus Features
5Select the desired zoom type ratio, 
and then select “OK”.
6Select the desired size of paper, and 
then select “OK”.
7Enter the desired number of copies.
8Press the Start key.
zWhen copying from the Platen Glass, place 
the next original, and follow the instructions 
described on the Touch Panel Display.
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode.
Enlarged or reduced 
according to the vertical or 
horizontal size of the paper 
(the one with the smaller 
magnification ratio is 
selected). 
Enlarged or reduced 
according to both vertical/
horizontal size of the paper. 
						

							68
 Chapter 2    More Menus Features
Effect Modes
Setting a Blank Edge
Unnecessary edge can be erased by setting a blank edge.
zWhen “Zoom” is selected, the erasing width varies depending on the zoom ratio.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Zoom / Effects”, and then 
select “Edge”.
5Select “XY” to set the same value for X 
and Y, or “X” or “Y” to set a different 
value for X and Y.
XYSelect to set the same erasing width 
for all sides.
XSelect to set the erasing width for the 
right and left sides.
YSelect to set the erasing width for the 
top and bottom sides. 
						

							69
 Chapter 2    More Menus Features
6Enter the erasing width with “S” and 
“T”, or the Keypad, and then select 
“OK”.
zThe erasing width can be set in 1 mm 
increments from 5 mm to 99 mm.
7Enter the desired number of copies.
8Press the Start key.
zWhen copying from the Platen Glass, place 
the next original, and follow the instructions 
described on the Touch Panel Display. (The 
instructions are displayed only when the 
Sort mode other than “Non Sort” is 
selected.)
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode. 
						

							70
 Chapter 2    More Menus Features
Eliminating Dark Inner Binding Shadows
When copying original such as the center of folding position may be shaded, the shade can be easily 
eliminated.
zWhen “Zoom” is selected, the erasing width varies depending on the zoom ratio.
zWhen “Overlay” or “Form Overlay” is selected, this function cannot be executed for the overlay original.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “More Menus”.
4Select “Zoom / Effects”, and then 
select “Book”.
5Enter the erasing width with “S” and 
“T”, or the Keypad, and then select 
“OK”.
zThe erasing width can be set in 1 mm 
increments from 5 mm to 99 mm.
6Enter the desired number of copies.
7Press the Start key.
zWhen copying from the Platen Glass, place 
the next original, and follow the instructions 
described on the Touch Panel Display. (The 
instructions are displayed only when the 
Sort mode other than “Non Sort” is 
selected.)
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode.
The shade is erased.