Panasonic Digital Color Imaging Systems For Copier Dp C266 Operating Instructions

							31
 Chapter 1    Basic Menu Features
Sharpness
The original can be copied by softening or sharpening the outline of the image.
1Select “Sharpness”.
zTo display this screen, refer to step 1 of 
Background Removal (see page 27).
2Adjust the sharpness with “Lower” or 
“Higher”, and then select “OK”.
zThe screen will return to step 1. 
Select “OK”, and then proceed to steps 6 to 
8 of Quality Adjusting (see page 26).
Lower
Higher
LowerEach time it is selected, the 
sharpness level decreases by 
1 grade lower. (The image 
outline is softened.)
HigherEach time it is selected, the 
sharpness level increases by 1 
grade higher. (The image 
outline is sharpened.) 
						

							32
 Chapter 1    Basic Menu Features
Saturation
The original can be copied with the adjusted saturation.
1Select “Saturation”.
zTo display this screen, refer to step 1 of 
Background Removal (see page 27).
2Adjust the saturation with “Lower” or 
“Higher”, and then select “OK”.
zThe screen will return to step 1. 
Select “OK”, and then proceed to steps 6 to 
8 of Quality Adjusting (see page 26).
Higher Lower
LowerEach time it is selected, the 
saturation level decreases by 1 
grade lower, reducing the color 
saturation.
HigherEach time it is selected, the 
saturation level increases by 1 
grade higher, increasing the 
color saturation. 
						

							33
 Chapter 1    Basic Menu Features
Color Balance
The original can be copied with the adjusted density level (Darker, Medium, and Lighter) of Yellow, 
Magenta, Cyan, and Black.
zThe density of each color can be fine tuned for each of the three density levels.
This function is useful for the fine adjustment of color photos. Unlike image editing software, this function 
cannot greatly change the color tone since the adjustable range at each density level is very narrow.
1Select “Color Balance”.
zTo display this screen, refer to step 1 of 
Background Removal (see page 27).
2Select “Cyan”, and then adjust Darker 
Areas, Medium Areas, and Lighter 
Areas with “-” and “+”.
zThe density range from the darkest level 
(100%) to the lightest level (0%) is equally 
divided into three range areas.
3Select remaining colors, and then 
adjust the Color Balance as shown in 
step 2.
4Select “OK”.
zThe screen will return to step 1. 
Select “OK”, and then proceed to steps 6 to 
8 of Quality Adjusting (see page 26).
Darker AreasDarkest area
Medium 
AreasArea between the darkest and 
lightest areas
Lighter 
AreasLightest area 
						

							34
 Chapter 1    Basic Menu Features
Proof Copying
When making more than one copy, the first copy can be printed as a proof copy.
After confirming its quality, the remaining copies can be printed.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select the copy features if necessary.
4Enter the desired number of copies.
5Select “Proof Set”.
6Press the Start key.
The first copy is printed and the Confirmation 
screen appears.
7If the copy quality is satisfactory, 
select “Ye s”.
The remaining copies are printed.
‰If the copy quality is not satisfactory
1Select “No” to return to the Basic Menu 
screen.
2Place the original again.
3Adjust the quality settings.
4Press the Start key. 
A proof copy is printed and the Confirmation 
screen appears. Confirm if the copy quality is 
acceptable.
5Select “Ye s”.
The remaining copies are printed.
The remaining copies are 
made after confirmation. One copy as a 
proof copy 
						

							35
 Chapter 1    Basic Menu Features
Confir ming/Editing the Selected Copy 
Features
Before copying, the settings of “More Menus” can be checked, changed, and deleted.
1Select “Confirm Settings”.
2Check the settings, and then select 
“Close”.
zIf “Confirm Settings” is selected, the setting 
screen is displayed and the settings (except 
1 -> 1) can be changed.
zIf “Reset All” is selected, all the settings are 
canceled.
zIf “Preset Jobs” is selected, the job 
registration screen is displayed to register 
jobs. Refer to Storing a Job in Memory 
(see page 36).
Ex:Changing the Non Sort mode to the Shift-
Sort mode when optional Finisher and 
Punch Unit are installed
Select “Non Sort”.
Select “Shift-Sort”, and then select “OK”.
Select “Close”. 
						

							36
 Chapter 1    Basic Menu Features
Storing a Job in Memor y
A copy job can be registered as a preset job. It is useful to register the frequently used settings as 
Preset Jobs.
zRefer to Recalling a Preset Job Stored in Memory (see page 37).
zOnce registered, the copy job settings are kept in the job memory until they are overwritten by new settings.
zA Proof Copy job cannot be registered in the job memory. 
z“M1:”/“M2:” cannot be registered when the Manual Skyshot mode is selected. Refer to Copier Settings in the 
Operating Instructions (For Function Parameters) of provided CD-ROM.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select the copy features (see pages 
10 to 35 and 42 to 105).
4Enter the desired number of copies.
5Select “Preset Jobs”.
6Select “Save”, and then select a job 
button without a job registered.
zThe job button, in which a job has been 
registered, has a job name.
7Enter a job name, and then select 
“OK”.
zUp to 20 characters can be entered.
zFor instructions on how to enter characters, 
refer to Using the Keyboard in the 
Operating Instructions (For Function 
Parameters) of provided CD-ROM.
zAfter completing the editing of the job name, press 
the Reset key to return to the initial screen of the 
currently active mode. 
						

							37
 Chapter 1    Basic Menu Features
Recalling a Preset Job Stored in Memor y
The specific copy job will be done by recalling the registered preset jobs.
zRefer to Storing a Job in Memory (see page 36).
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select “Preset Jobs”.
4Select a stored job.
zJob buttons without names, indicate that 
jobs are not registered.
zIf the Confirmation screen “Ready for M 1 
Memory Copy” is displayed, select “Close”.
5To confirm the job settings, select 
“Confirm Settings”, and then select 
“Close”.
zTo change the setting, refer to Confirming/
Editing the Selected Copy Features (see 
page 35).
6Press the Start key. 
						

							38
 Chapter 1    Basic Menu Features
Checking the Waiting to Copy Job
A list of jobs currently being printed or waiting to print can be displayed. The following types of jobs can 
be displayed.
• All jobs
•Copy jobs
Waiting to print jobs can be deleted.
Displaying a List of All Jobs
A list of all the jobs currently being printed or 
waiting to print can be displayed.
1Press the Copy key if the machine is 
set to other function mode.
2Select “Output Queue”.
The Output Queue screen is displayed, and a 
list of all the jobs currently being printed or 
waiting to print are displayed.
3Select “Close”.
Displaying a List of Copy Jobs
A list of Copy jobs currently being printed or 
waiting to print can be displayed.
1Select “Copy” in the Output Queue 
screen.
zA list of Copy jobs currently being printed or 
waiting to print is displayed.
2Select “Close”. 
						

							39
 Chapter 1    Basic Menu Features
Deleting Copy Jobs
The jobs in the Ready status can be deleted.
1Select “Copy” in the Output Queue 
screen.
zTo display the Output Queue screen, refer to 
Checking the Waiting to Copy Job (see 
page 38).
2Select a job, and then select “Delete”.
zWhen deleting all jobs, select “Select All”, 
and then select “Delete”.
The screen to confirm the job deletion is 
displayed.
3Select “Yes”.
The selected Copy job is deleted.
4Select “Close”.
CopySelect when deleting a copy 
job.
PrintSelect when deleting a print 
job.
zRefer to the Operating 
Instructions (For Printer) 
of provided CD-ROM. 
						

							40
 Chapter 1    Basic Menu Features
Completion Notice
If the Completion Notice is set, you will be notified on your computer when copying is completed.
zBefore using this function, install the Panasonic Document Management System and Printer Driver, and 
then configure each software.
zTo register the IP Address of your computer, refer to Network Scanner Settings and Completion Notice 
Function in the Operating Instructions (For User Setup) of provided CD-ROM.
1Place original(s).
zRefer to Placing Originals (see page 6).
2Press the Copy key if the machine is 
set to other function mode.
3Select the copy features if necessary.
4Select “Completion Notice”.
5Select an index tab or “Favorites” to 
display the registered computers.
6Select a designated computer, and 
then select “OK”.
7Enter the desired number of copies.
8Press the Start key.
zWhen copying from the Platen Glass, place 
the next original, and follow the instructions 
described on the Touch Panel Display.
zA completion notice will be sent to the 
specified computer when copying is 
completed.
zAfter finishing copying, press the Reset key to 
return to the initial screen of the currently active 
mode.