Panasonic Digital Camera Dmc Lx100 Owners Manual For Advanced Features

							241SQW0021
Wi-Fi
Operating the camera by connecting it to a smartphone
[Send Images Stored in the Camera]
1Set the menu
 → [New Connection] → [Send Images Stored in the Camera] 
→ [Smartphone]
2Select [Via Network] or [Direct] and press [MENU/SET]
 ■When connecting with [Via Network](On the camera) Connect the camera to a wireless access point  (→264)
(On your smartphone)
 Set Wi-Fi function to “ON” Select the wireless access point you co nnected to the camera, and set Start “Image App” (→228)
 ■When connecting with [Wi-Fi Direct] or [WPS Connection] in [Direct](On the camera) Connect the camera to a smartphone (→267)
(On your smartphone)
 Start “Image App” (→228)
 ■When connecting with [Manual Connection] in [Direct]Perform step 2 (→229).
3Select the device you wish to connect to • When the connection is established, the confirmation screen for the transmission setting is  displayed. Check the setting and press [MENU/SET]. T o change the send setting, press the 
[DISP.] button.  (→271)
4Select [Single Select] or [Multi Select]
[Single Select] Select the picture Press [MENU/SET]
[Multi Select]
  Select the picture (repeat) • If selected again, the setting will be canceled.  Select [OK] • The number of pictures that can be sent by [Multi Select] is  limited.00730074
007500760077
0072OK
 • A confirmation screen is displayed. If you select [Yes], the operation is executed. • To change the send setting, press [DISP .] button. 
 • To close the connection, select [

Exit].           
						

							242SQW0021
Wi-Fi
Displaying still pictures on a TV
You can display still pictures on a TV that is compatible with a DLNA certified digital 
media renderer (DMR) function.
Preparation
Set the TV to DLNA waiting Mode.
 • Read the operating instructions for your TV
.
1Set the menu
 → [New Connection] → [Playback on TV]
2Select [Via Network] or [Direct] to connect (→263)
3Select the device you wish to connect to • When the connection is established, the screen is displayed.
4Take or play back still pictures on this unit • To change the setting or disconnect, press [Wi-Fi] button.  (→226)
(Y ou can also close the connection by pressing  →  [Setup] → [Wi-Fi] → 
[Wi-Fi Function] → [Yes].)
 ●When you display the pictures on a TV using the Wi-Fi function, they are not output using 4K 
resolution. To output pictures using 4K resolution, connect this unit to the TV using an HDMI micro 
cable. (→276)
 ●When a TV is connected to this unit, the TV screen may temporarily return to the status before the 
connection. Pictures are displayed again when you take or play back pictures.
 ●Even if [Effect] and [Sound] are set on this unit, these settings are disabled when the pictures are 
played back on a TV during Slide Show playback.
 ●It may take some time to establish the Wi-Fi connection or it may not be connected at all 
depending on the distance from this unit to the TV.
Not available in the following cases:
 ●Playback of motion pictures or panorama pictures, and continuous playback of group pictures are 
not displayed on a TV.
 ●During the multi/calendar playback, pictures displayed on the screen of this unit are not displayed 
on TV.      
						

							243SQW0021
Wi-Fi
Wireless printing
You can print out recorded still pictures wirelessly from a PictBridge (wireless 
LAN-compatible)*
 printer.
*
  Compliant with the DPS over IP standards. 
Contact the printer manufacturers for details on PictBridge (wireless LAN-compatible) printers.
 ■Sending method, and pictures that can be sent
JPEG RAW MP4 AVCHD
[Send Images Stored in the Camera] ○–––
 • Some images may not be played back or sent depending on the device. • For more details about picture sending methods.  (→270)
1Set the menu
 → [New Connection] → [Send Images Stored in the Camera] → [Printer]
2Select [Via Network] or [Direct] to connect (→263)
3Select a printer you want to connect
4Select the still picture and print • Pictures are selected the same way as when connecting by USB connection cable (supplied). 
For more details (→287) .
 • To change the setting or disconnect, press [Wi-Fi] button.  (→226)
(Y

ou can also close the connection by pressing the [
  ] button.)
Not available in the following case:
 ●Motion pictures cannot be printed.      
						

							244SQW0021
Wi-Fi
Sending pictures to AV device
Still pictures and motion pictures can be sent to AV devices in the home (home AV 
devices), such as DLNA compatible recorders.
Wireless access pointHome AV device
 ■Sending method, and pictures that can be sent
JPEG RAW MP4 AVCHD
[Send Images While Recording] (→245) ○–––
[Send Images Stored in the Camera] 
(→246) ○
–––
 • Some images may not be played back or sent depending on the device. • See the operating instructions of the destination device for more information about 
picture playback.
 • For more details about picture sending methods.  (→270)
Preparations
When sending a picture to AV devices, set your device to DLNA waiting Mode.
 • Read the operating instructions of your device for details.      
						

							245SQW0021
Wi-Fi
Sending pictures to AV device
[Send Images While Recording]
1Set the menu
 → [New Connection] → [Send Images While Recording] → [AV device]
2Select [Via Network] or [Direct] to connect (→263)
3Select the device you wish to connect to • When the connection is established, the confirmation screen for the transmission setting is displayed. Check the setting and press [MENU/SET]. T o change the send setting, press [DISP.] 
button. (→271)
4Take still pictures • To change the setting or disconnect, press [Wi-Fi] button.  (→226)
Y ou cannot change the settings while sending still pictures. Wait until sending is complete.
(You can also close the connection by pressing 
 →  [Setup] → [Wi-Fi] → 
[Wi-Fi Function] → [Yes].)      
						

							246SQW0021
Wi-Fi
Sending pictures to AV device
[Send Images Stored in the Camera]
1Set the menu
 → [New Connection] → [Send Images Stored in the Camera] 
→ [AV device]
2Select [Via Network] or [Direct] to connect (→263)
3Select the device you wish to connect to • When the connection is established, the confirmation screen for the transmission setting is  displayed. Check the setting and press [MENU/SET]. T o change the send setting, press [DISP.] 
button. (→271)
4Select [Single Select] or [Multi Select]
[Single Select] Select the picture Press [MENU/SET]
[Multi Select]
  Select the picture (repeat) • If selected again, the setting will be canceled.  Select [OK] • The number of pictures that can be sent by [Multi Select] is  limited.00730074
007500760077
0072OK
 • A confirmation screen is displayed. If you select [Yes], the operation is executed. • To change the send setting, press [DISP .] button. 
 • To close the connection, select [

Exit].           
						

							247SQW0021
Wi-Fi
Sending pictures to a PC
Still pictures and motion pictures recorded by the camera can be sent to a PC.
 ■Sending method, and pictures that can be sent
JPEG RAW MP4AVCHD*
[Send Images While Recording] (→249) ○○ ––
[Send Images Stored in the Camera] 
(→250) ○
○○○
*  Motion pictures recorded in [AVCHD] can be sent in file sizes of up to 4 GB. Files larger than 4 GB 
cannot be sent.
 • Some images may not be played back or sent depending on the device. • See the operating instructions of the destination device for more information about  picture playback.
 • For more details about picture sending methods.  (→270)
Preparations • Turn the computer on. • Prepare folders for receiving images on the PC before sending a picture to the PC.  (→248) • If the standard settings are changed for the workgroup on the connected PC, you must change 
settings in [PC Connection

] on this unit. (→272)      
						

							248SQW0021
Wi-Fi
Sending pictures to a PC
To create a folder that receives images
 • Create a PC user account (account name (up to 254 characters) and password (up to 
32 characters)) consisting of alphanumeric characters.  An attempt to create a receive 
folder may fail if the account includes non-alphanumeric characters.
 ■When using “PHOTOfunSTUDIO”
  Install “PHOTOfunSTUDIO” on the PC • “PHOTOfunSTUDIO” is not compatible with Mac. • For details on hardware requirements and installation, read “Installing supplied software” 
(→281, 283)
.
  Create a folder that receives images with “PHOT OfunSTUDIO” • To create the folder automatically, select [Auto-create]. To specify a folder, create a new folder, 
or set a password to the folder , select [Create manually].
 • For details, refer to the operating instructions of “PHOTOfunSTUDIO” (PDF).
 ■When not using “PHOTOfunSTUDIO”
(For Windows)
Supported OS: Windows 8.1 / Windows 8 / Windows 7 / Windows Vista
Example: Windows 7
  Select a folder you intend to use for receiving, then right-click  Select [Properties], then enable sharing of the folder • For details, refer to the operating instructions of your PC or Help on the operating system.
(For Mac)
Supported OS: OS X v10.5 to v10.9
Example: OS X v10.8
  Select a folder you intend to use for receiving, then click on the items in the following 
order 
[File] → [Get Info]
  Enable sharing of the folder • For details, refer to the operating instructions of your PC or Help on the operating system.      
						

							249SQW0021
Wi-Fi
Sending pictures to a PC
[Send Images While Recording]
1Set the menu
 → [New Connection] → [Send Images While Recording] → [PC]
2Select [Via Network] or [Direct] to connect (→263)
3Select the PC you want to connect to • If the PC you want to connect to is not displayed, select [Manual Input], then enter the computer 
name (for Mac, enter the NetBIOS name).
4Select the folder you want to send to • When the connection is established, the confirmation screen for the transmission setting is  displayed. Check the setting and press [MENU/SET]. T o change the send setting, press [DISP.] 
button. (→271)
5Take still pictures • To change the setting or disconnect, press [Wi-Fi] button.  (→226)
Y ou cannot change the settings while sending still pictures. Wait until sending is complete.
(You can also close the connection by pressing 
 →  [Setup] → [Wi-Fi] → 
[Wi-Fi Function] → [Yes].)      
						

							250SQW0021
Wi-Fi
Sending pictures to a PC
[Send Images Stored in the Camera]
1Set the menu
 → [New Connection] → [Send Images Stored in the Camera] → [PC]
2Select [Via Network] or [Direct] to connect (→263)
3Select the PC you want to connect to • If the PC you want to connect to is not displayed, select [Manual Input], then enter the computer 
name (for Mac, enter the NetBIOS name).
4Select the folder you want to send to • When the connection is established, the confirmation screen for the transmission setting is  displayed. Check the setting and press [MENU/SET]. T o change the send setting, press [DISP.] 
button. (→271)
5Select [Single Select] or [Multi Select]
[Single Select] Select the picture Press [MENU/SET]
[Multi Select]
  Select the picture (repeat) • If selected again, the setting will be canceled. Select [OK] • The number of pictures that can be sent by [Multi Select] is  limited.00730074
007500760077
0072OK
 • A confirmation screen is displayed. If you select [Yes], the operation is executed. • To change the send setting, press [DISP .] button. 
 • To close the connection, select [

Exit].
 ●Folders sorted by the sent date are created in the specified folder , and pictures are saved in those 
folders.
 ●If the screen for a user account and password entry appears, enter the one you set on your PC. ●If the computer name (for Mac, the NetBIOS name) contains spaces, etc., the name may not be 
properly recognized. If you cannot connect, we recommend changing the computer name (for 
Mac, the NetBIOS name) to a combination of 15 or less alphanumeric characters only .