Panasonic Color Cctv Camera Wv Cw864a Operating Instructions

-31- 3. Open the SET UP menu to stop learning.
Notes:
•It is recommended to set PAN LIMIT to ON for
patrol-learn. Otherwise PAN LIMIT is invalid in
playback. 
•If the power fails in the patrol-learn mode, start
the patrol-learn function again from the starting
point.
•LEARN also stops 1 minute  after starting if the
memory is full.
•Auto refreshing may be activated in the patrol
play mode or the auto mode to calibrate the lens
position.
Patrol Play with a Controller Having the PATROL
Key
1. Press the...

-32-
CNT-CLS 1, 2 (Output)
Two contact closure signals (Open collector type) are
output through the Alarm Output connector.
1. Move the cursor to CNT-CLS 1, and select OFF,
ALARM or AUX 1 with the joystick.
The factory default setting is OFF.
When ALARM is selected, TIME OUT appears.
Select an appropriate duration from among 100 MS,
200 MS, 1000 MS (1 s), 2000 MS (2 s) and 4000 MS
(4 s) with the joystick.
The factory default setting is 100 MS.
Note:The shorter the duration, the more frequent
will be the...

-33-
ON:10 - fold electronic zoom is available with the
ZOOM switch on the controller.
OFF:The electronic zoom function is not used.
Notes:
•A scene magnified by the electronic zoom func-
tion may be inferior in picture quality to a non-
magnified one.
•The electronic zoom does not function in the pre-
set position setting mode.
•To set preset positions directly from WV-CU360
System Controller, you need to set the electronic
zoom function temporarily to OFF.
●Preset Alarm (PRESET ALM)
An alarm output is...

-34-
■Camera Setting
●To Display the Camera Setting Menu
Move the cursor to CAMERA O, and press the CAM
(SET) key. The camera setting menu appears.
●Camera Identification (CAMERA ID)
1. Move the cursor to CAMERA ID, and select ON to
display the camera identification with the joystick.
2. Follow the steps below to edit the camera ID char-
acters.
2-1 Move the cursor to CAMERA ID and press the
CAM (SET) key to display the character editing
menu.
2-2 Move the cursor to the character you want to edit
or...

-35-
●Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or
MANUAL with the joystick. When you select ALC,
set backlight compensation.
Note:The backlight compensation submenu associ-
ated with this menu is described separately and
should be set up after installing the camera at
the site and observing the actual site picture.
2. When MANUAL is selected, quit the setup menu by
pressing the MON (ESC) key. Press the OPEN or
CLOSE key on the controller for iris adjustment.
(1)...

-36- 6. If you want to change the picture contrast, move the
I cursor for LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM (SET)
key to return to the CAM SET UP menu.
To return to the camera picture, press the F4 button.
●Shutter Speed Setting (SHUTTER)
Note:When ON is selected for SUPER-D2 on the ALC
CONT menu, only OFF and AUTO are available.
To select an electronic fixed shutter speed, select
OFF for SUPER-D2 in the menu.
Move the cursor to SHUTTER and select the elec-
tronic...

-37- •When ON is selected for SUPER-D2 on the ALC
CONT menu
Notes:
•When ON is selected for SUPER-D2 in the ALC
CONT menu, FIX is not available for this item.
•When AUTO is selected for SENS UP and ON is
selected for SUPER-D2, the SENS UP function has
priority so that the SUPER-D2 function is not activat-
ed automatically.
•While the SENS UP function is selected, noise or
spots may appear in the picture when the sensitivity
of the camera is increased. This is a normal phe-
nomenon.
●Synchronization...

-38- 8. Match the vertical phase for both video output sig-
nals as closely as possible with the joystick.
Notes:
•When the | cursor reaches the + end, it jumps
back to –. At the same time, COARSE is incre-
mented by one step to enable a continuous
adjustment. The reverse takes place when the |
cursor reaches the – end.
•When the joystick is kept at the right or left for
one second or more, the | cursor moves quick-
ly.
•To reset COARSE and FINE to the preset values,
press the F2 button of WV-CU550C. For...

-39-
●Motion Detector (MOTION DET)
1. Move the cursor to MOTION DET and select ON or
OFF with the joystick.
2. If ON is selected, press the CAM (SET) key. The
MOTION DETECT menu appears.
You can mask the areas in this menu.
3. Move the cursor to MASK SET and press the CAM
(SET) key. 48 mask areas appear on the monitor
screen.
Refer to Light Control Setting on page 35 for mask-
ing operations.
4. After masking areas, press the MON (ESC) key. The
MOTION DETECT menu appears on the monitor
screen.
5. Move...

•The alarm signal will take approx. 0.2 seconds to
reach the alarm terminal of the VCR after the camera
detects the object.
Because the alarm signal is multiplexed on the
video signal, it may be mistakenly interpreted by
other video equipment as a time code signal.
Therefore, when this camera is not used in a
Panasonic Intelligent CCTV System, select OFF to
prevent the above from occurring.
●Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the follow-
ing mode with the joystick. S,...