Panasonic Color Cctv Camera Wv Cw864a Operating Instructions

-21-
To Enter the Next ID without Returning to the
Preset Setting Menu
(1) In the preset ID setting menu, move the cursor to
the top line and select a desired position number
with the joystick.
(2) Enter, copy, change or delete the ID as
described above.
To Return to the Preset Setting Menu
Move the cursor to RET and press the CAM (SET)
key.
●Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or
MANUAL with the joystick.
The factory default setting is ALC.
ALC:The lens...

-22- See the pages below for the settings respectively.
Shutter speed: page 36
AGC: page 36
Electronic sensitivity enhancement: page 36
White balance: page 38
Motion detector: page 39
Auto focus: page 40
●Preset Speed Setting (PRESET
SPEED)
Move the cursor to PRESET SPEED and select a
speed with the joystick.
●To Return to the Preset Number Set
Menu
Move the cursor to RET and press the CAM (SET)
key. The PRESET NUMBER SET menu appears with
the * mark on the right of the preset position num-
ber.
●To...

-23-
■Home Position Setting (HOME
POSITION)
1. To set a position number for the home position
Move the cursor to HOME POSITION and select a
desired position number with the joystick.
2. Select OFF if you are not using the home position
function.
■Self Return Setting (SELF
RETURN)
1. Move the cursor to SELF RETURN, select a return
time from among the following with the joystick and
press the CAM (SET) key to confirm your selection.
MIN stands for minute(s).
2. Select an operation from among the following...

-24- This determines the starting point and the cursor
moves to END.
(3) Move the joystick to select a panning endpoint
and press the CAM (SET) key.
This determines the endpoint and the cursor
moves to POSITION.
4. To set a panning speed
Move the cursor to SPEED, and set a panning
speed with the joystick.
The panning speed increases when the joystick is
moved to the right, and decreases when it is moved
to the left.
Caution:If the panning range is changed after the
camera has not panned for a long time...

-25- (2) Move the cursor to ZOOM, press the CAM (SET)
key, move the joystick to settle the ZOOM posi-
tion and return to the AUTO PAN menu. The
manual zoom operation is not available in the
TELE direction beyond the settled zoom position.
OFF:Does not limit the manual zoom operation.
Notes:
•When the panning, tilting, zooming or focusing in
the SEQ, SORT or PATROL mode is controlled
manually, the auto mode function should be can-
celled.
To activate the auto mode, select the desired
auto mode again or...

-26-
●Password Lock (PASSWORD LOCK)
Caution:For security, do not operate your VCR for
recording while the password menus are displayed
on the monitor.
A 3-digit number is used for a password to limit
access to all settings.
1. Move the cursor to PASSWORD LOCK, then select
ON or OFF with the joystick.
Note:ON or OFF can be selected only after going
through the password verification.
OFF:You can change all settings.
ON:You cannot change settings at all nor operate
AUTO PAN, SEQ, SORT, and PATROL.
2. Press...

-27-
■Special 1 Menu Setting
(SPECIAL 1)
●Privacy Zone (PRIVACY ZONE)
Up to 8 unwanted zones can be masked on the monitor
screen.
1. Move the cursor to PRIVACY ZONE and select ON
or OFF with the joystick. Press the CAM (SET) key to
display the ZONE NUMBER setting menu.
ON:Preset privacy zones are veiled on the monitor
screen.
OFF:The veiling function does not work.
2. Select a zone number with the joystick, and press
the CAM (SET) key.
•A zone number followed by * (asterisk) indicates
that the zone has...

-28- Moving the joystick in the L direction decreases
the zone frame, and moving it in the H direction
increases it. However, the aspect ratio is fixed at
3 to 4.
The privacy zone setting has been completed.
The menu returns to the ZONE NUMBER setting
menu. If DEL is selected, zone setting is
released and the ZONE NUMBER setting menu
appears.
3-6
•To complete new settings and repeat other set-
tings, move the cursor to SET and press the
CAM (SET) key. The ZONE NUMBER setting
menu reappears.
•To cancel...

-29- 3. Move the cursor to PUSH SET for ZOOM/FOCUS,
and press the CAM (SET) key. ZOOM/FOCUS is
highlighted and U ZOOM D/L FOCUS R appears.
4. Adjust the zoom or focus with the joystick.
5. Move the cursor to POSI 
O, and press the CAM
(SET) key. The area title position appears on the
monitor screen. If needed, change the display posi-
tion with the joystick, and press the MON (ESC) key.
An area title always appears under the camera ID.
If the camera ID and an area title are set to be
shown in separate...

-30-
To Quit Editing
•To return to the AREA TITLE menu, move the cursor
to RET, and press the CAM (SET) key.
•To cancel one area title, move the cursor to RESET
in the AREA TITLE menu, and press the CAM (SET)
key.
•To return to the SPECIAL 1 menu, move the cursor
to RET, and press the CAM (SET) key.
•To erase all the area titles, move the cursor to
RESET in the AREA TITLE (USER) selection menu,
and press the CAM (SET) key.
Notes:
•An area title appears under the camera ID if both
are set in the same...