Panasonic Color Cctv Camera Wv Cw864 Operating Instructions

22
■Deleting Preset Positions
1. Move the cursor to PRESET 1 and select the position number to
be deleted by using the joystick.
2. Press the CAM (SET) key to display the preset setting menu.
3. Move the cursor to DEL and press the CAM (SET) key.
This deletes the preset position and the PRESET NUMBER SET
menu appears. The * mark on the right of the number disappears.
Note:Your selected preset number is cancelled only in the SEQ
and SORT mode. The previously set parameters (for PAN,
TILT positions, etc.)...

23
■Auto Mode Selection (AUTO MODE)
1. To set auto mode
Move the cursor to AUTO MODE and select a mode by moving
the joystick to the right or left.
The factory default setting is OFF.
Modes change as follows:
OFF:No automatic operation. The camera can be operated only
manually.
SEQ:The camera operates in the sequence of preset positions in
numerical order.
SORT:The camera operates in the sequence of preset positions
counterclockwise from the Pan/Tilt starting point.
AUTO PAN:The camera automatically...

24
5. To set pan limit ON/OFF
Move the cursor to PAN LIMIT and select ON or OFF by mov-
ing the joystick to the right or left.
The factory default setting is OFF.
ON:Manual pan is limited from the starting point to the end-
point specified by position setting. Set ENDLESS to OFF
before PAN LIMIT is set to ON.
OFF:Manual pan is not limited.
Note:When ON is selected for PAN LIMIT, manual pan moves the
camera away from the other side (PAN LIMIT) of the start-end
range.
6. To set ENDLESS to ON/OFF
Move the...

25
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 LOCAL/REMOTE
 SPECIAL1
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
ON
LOCAL
Setup menu
■Auto Pan Key Setting
(AUTO PAN KEY)
This is used for assigning one of the following auto functions to the
AUTO key on the controller. Pressing the AUTO key activates the
assigned function after this setting.
•Move the cursor to AUTO PAN KEY and select an auto function by
moving the joystick to the right or left.
The...

26
■Local/Remote Setting
(LOCAL/REMOTE)
•Move the cursor to LOCAL/REMOTE, and select LOCAL or
REMOTE by moving the joystick to the right or left.
The factory default setting is LOCAL.
Note:The REMOTE mode does not work when the WV-RM70,
WV-CU360, WV-CU161, WJ-FS616 or WV-CU550 series is
connected. Make sure that LOCAL mode is selected in this
case.
■Special 1 Menu Setting (SPECIAL 1)
●Privacy Zone (PRIVACY ZONE)
Up to 8 unwanted zones can be masked on the monitor screen.
1. Move the cursor to PRIVACY...

27
** ZONE NUMBER 1*/8 **  
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
     U TILT D/L PAN R 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      –       +
RET
PAN/TILT setting menu3. To register a new zone
3-1 For PAN/TILT, move the cursor to PUSH SET and press the
CAM (SET) key.
3-2 Adjust the pan and tilt position so that the desired position
comes into the zone frame by using the joystick.
Note:Zone setting is not available while the zone frame is not
shown, for example, when the camera is tilted...

28
●Proportional Pan/Tilt (PROPO. P/T)
•Move the cursor to PROPO. P/T and select either ON or OFF by
moving the joystick to the right or left.
Factory default setting: ON
ON:Pan/tilt speed is in inverse proportion to the zoom ratio as fol-
lows:
Zoom ratio Speed level
x1 7 (fastest)
x2 5
x4 3
x8 1
x15 or more 0 (slowest)
* The speed level values are approximate.
OFF:The speed is constant at the fastest level regardless of the
zoom ratio.
●Area Title (AREA TITLE)
Up to 8 area titles can be added in...

29
3. Move the cursor to PUSH SET for ZOOM/FOCUS, and press the
CAM (SET) key. ZOOM/FOCUS is highlighted and “U ZOOM D/L
FOCUS R” appears.
4. Adjust the zoom or focus by using the joystick.
5. Move the cursor to POSI O, and press the CAM (SET) key. The
area title position appears on the monitor screen. If needed,
change the display position by using the joystick, and press the
MON (ESC) key.
An area title always appears under the camera ID.
If the camera ID and an area title are set to be shown in...

30
To Quit Editing
•To return to the AREA TITLE menu, move the cursor to RET, and
press the CAM (SET) key.
•To cancel one area title, move the cursor to RESET in the AREA
TITLE menu, and press the CAM (SET) key.
•To return to the SPECIAL 1 menu, move the cursor to RET, and
press the CAM (SET) key.
•To erase all the area titles, move the cursor to RESET in the AREA
TITLE (USER) selection menu, and press the CAM (SET) key.
Notes:
•An area title appears under the camera ID if both are set in
the same...

31
Patrol-learn with a Controller Having the PATROL Key
1. Press the PATROL LEARN key and PROGRAM key simultaneous-
ly to start patrol-learn. The setup menu displays “LEARNING”, and
the starting points are stored.
2. Operate patrol-learn manually. The operation data is stored.
3. To stop patrol-learn, press the PATROL STOP and PROGRAM key
simultaneously.
Patrol-learn with a Controller not Having the PATROL Key
1. Select patrol-learn in the setup menu, and then close the menu.
Starting points are stored...