Panasonic Color Cctv Camera Wv Cw864 Operating Instructions

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Model No.      WV-CW864  
Color CCTV Camera
Operating Instructions
ENGLISH
FRANÇAIS 

2
The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit in
the space provided and retain this book as a per-
manent record of your purchase to aid identifica-
tion in the event of theft.
Model No.
Serial No.
The lightning flash with arrow-
head symbol, within an equilater-
al triangle, is intended to alert the
user to the presence of uninsu-
lated dangerous voltage within
the products enclosure that may
be of sufficient magnitude to con-...

3
ENGLISH
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves or other apparatus (includ-
ing amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A...

4
•Outdoor enclosure based on IP66* of
IEC60529 standard
* Waterproof structure resistant to powerful
jetting as classified by the International
Protection code
•Provided with built-in heater and fan
•High quality picture of 768 x 494 pixels
•Minimum illumination of 0.5 lx (0.05 foot-can-
dle) for color and 0.03 lx (0.003 foot-candle)
for black/white surveillance 
(at AGC ON (HIGH), SENS UP x 2)
•Digital flip allows a 180 ° tilting to trace
objects passing under the camera.
•Privacy zone feature enables...

5
■Camera Cleaning
Even if this function is used, noise may be produced on the monitor screen, or the preset position may
deviate in the course of prolonged use.
In such cases, activate the refresh mode on the special 2 menu. (See page 46.)
To use this camera with the WJ-SX550B Matrix Switcher, set the auto cleaning function activated on the
Matrix Switcher side, then clean WV-CW864 one time a day.
■Preset Data Uploading or Downloading
To download the preset data from the camera to the controller or...

6
6. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when it
is dirty.
When the dirt is hard to remove, use a mild
detergent and wipe gently. Care should be
taken not to scratch the dome cover when
wiping it.
Afterwards, wipe off the remaining detergent
with a dry cloth.
7. Never aim the camera at the sun.
Whether or not the camera is in use , never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused....

7
uAttachment Pipe
iUpper Base
oFall Prevention Wire
!0Enclosure
!1Dome qAlarm Input Connector
wAlarm Output Connector
eVideo Output Connector
rData Port
tPower Cord for Heater
yPower Connector for Camera
CONSTRUCTION
w
e
r
t
yq
u
i
!0
!1 o 

9 8
SETUP
White
Balance
           ATW1/
 AWC  ATW2
Setup
Menu
Home
Position
SelectionSelf
Return
SettingAuto Pan
Key
SettingDigital
Flip
ON/OFFLocal/
Remote
Selection
Shutter
Speed
SelectionSensitivity
Up
ON/OFFWhite
Balance
          ATW1/
 AWC  ATW2
BLC
OFFLight 
Control
ALC/MANUAL
BLC
ON
Manual
Level
Adjustment
(Contrast)Manual
Mask
Area
Selection
INT
Manual
SelectionVD2
Automatic
SelectionManual
Level
AdjustmentManual
Level
Adjustment
V-phase
Manual
AdjustmentLL
Manual
Selection
Motion
Detector...

10
Open Special 2 F2 key
The keys (switches) to use for setup are shown in the table below. The joystick on the connected con-
troller may also be used for setup. The table also shows the functions versus the operations of the individ-
ual controllers. For details, see the manual for the controller to be used. Switches and controls are abbre-
viated as SW and CTRL respectively in the table.
OPERATE LOGINALARMFUNCTIONSXIRISCLOSE OPEN
NEAR FAR
WIDE TELEFOCUS
ZOOM AUTO FOCUS IRIS RESET
HOME SET UPALM...

11
■Setup Menu Description
●Presetting
(1) Position (POSITION SET)
Aligns the camera position and focal point by panning, tilting, zooming and focusing.
See page 17 for the setting.
(2) Preset Identification (PRESET ID)
Assigns the name for preset IDs (identification of up to 16 alphanumeric characters) and can be
switched on or off on the monitor screen.
See page 19 for the setting.
(3) Light Control (ALC/MANUAL)
Selects the ALC or MANUAL mode for adjusting the lens iris.
See page 20 for the setting....