Panasonic Color Cctv Camera Wv Cw864 Operating Instructions

12
●Auto Pan Key (AUTO PAN KEY)
This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the con-
troller.
After this setting, the AUTO key performs as assigned.
Note:The AUTO PAN LED on the controller does not light if a mode other than AUTO PAN is assigned.
●Digital Flip (DIGITAL FLIP)
In ON position, digital flip widens the range to 0 ° - 180 ° by reversing horizontal and vertical scanning
when the camera is tilted through the 90 ° (downright position if the camera is...

13
(6) Password Lock (PASSWORD LOCK)
This setting controls access to the privacy zone to be free or limited. If PASSWORD LOCK is set to
ON, ON(DIS) or OFF(DIS) for PRIVACY ZONE appears on the SPECIAL 1 menu.
(7) Cleaning (CLEANING)
This is used for refreshing the electro-mechanical contacts built into the camera. Use this function for
maintenance when the camera has been directed at a specific spot or panned over a specific range
for a long time.
(8) Electronic Zoom (EL-ZOOM)
Up to 10-fold electronic...

14
Note:The result of field setup of the mask area and level adjustment is fed back (effected) to the lens
iris control in ALC mode.
(3) Shutter Speed (SHUTTER)
You can select a shutter speed from among 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000,
1/4 000, and 1/10 000 seconds.
See page 39 for the setting.
(4) Gain Control (AGC)
You can set the gain of an image to automatic adjustment [AGC ON (LOW, MID, HIGH)] or fixed
(AGC OFF).
See page 39 for the setting.
(5) Electronic Sensitivity Enhancement...

15
(7) White Balance (WHITE BAL)
You can select either of three modes shown below for white balance adjustment:
•Auto-Tracing White Balance (ATW1)
In this mode, the color temperature is monitored continuously and thereby white balance is set auto-
matically. The color temperature range for the proper white balance is approx. 2 600 - 6 000 K.
Proper white balance may not be obtained under the following conditions:
1. The color temperature is out of the 2 600 - 6 000 K range.
2. When the scene contains...

16
SETTING PROCEDURES
The following setting procedures are described on the assumption that this model is used in combination
with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case a controller other than
the WV-CU550B is used, refer to the table on page 10.
■Menu Display
●Setup Menu Display
WV-CU550B
1. Select the camera number you want to set up and a monitor to
display SET UP MENU.
2. Display the D4 menu on the LCD by pressing the appropriate cur-
sor buttons.
3. Press the F1...

17
■Presetting
●Preset Menu Display
1.Displaying the preset menu directly
(1) Move the cursor to PRESET 1 Oand select the position num-
ber by moving the joystick to the right or left.
(2) Press the CAM (SET) key.
The preset setting menu appears on the monitor screen.
2.Displaying the preset menu from the PRESET NUMBER SET menu
(1) Move the cursor to MAP Oand press the CAM (SET) key.
The PRESET NUMBER SET menu appears on the monitor
screen.
(2) Move the cursor to the position number to be set and press...

18
3. Pan Offset
If the camera is replaced with a new one, the pan offset function
is used to adjust its positions to be the same as before except
patrol setting.
The system controller can download or upload the preset position
data.
Caution:The preset data for other cameras (WV-CS850A for
example) is incompatible with WV-CW864s. WV-CW864s
preset data will be destroyed if you upload the conventional
data. If this happened, reset the WV-CW864 to the default
settings. Download the factory settings into the...

19
●Preset Identification Setting (PRESET ID)
1.Move the cursor to PRESET ID on the preset setting menu and
select ON or OFF by moving the joystick to the right or left.
The factory default setting is OFF.
ON:Preset ID appears on the monitor screen.
OFF:Preset ID does not appear.
2.Press the CAM (SET) key to display the preset ID setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using the joystick,
and press the CAM (SET) key.
(2) The selected character appears in the...

20
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM (SET) key. The
display position set menu appears.
(2) Move the ID to the desired position by using the joystick, and
press the MON (ESC) key. The display position is set and the
monitor screen returns to the preset ID setting menu.
To Enter the Next ID without Returning to the Preset Setting
Menu
(1) In the preset ID setting menu, move the cursor to the top line
and select a desired position number by moving the...

21
●Dwell Time (DWELL TIME)
•Move the cursor to DWELL TIME and set a dwell time by moving
the joystick to the right or left. The factory default setting is 10S.
Dwell time changes as follows:
S stands for second(s), and MIN stands for minute(s).
●Scene File Setting (SCENE FILE)
1. To set a scene file number
Move the cursor to SCENE FILE and select a scene file number (1
to 10, or OFF) by moving the joystick to the right or left. The facto-
ry default setting is OFF. No scene file is selected at OFF.
2....