Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

							43
• The following steps of installation and connection should be taken by qualified service personnel or
system installers and should conform to all local codes.
• Make sure to switch the camera off before installation and connection.
• Do not install the camera near the air outlet of an air conditioner.
Camera mounting base
Camera
Camera mounting 
base
Fixing screw
Loosen and 
push
1234 ON1234 ON5678
 SW 1
SW 2
INSTALLATION
1. Disassembling the Camera
(1) Loosen the fixing screw to separate the
camera mounting base and the camera.
Push up the screwdriver once before
removing the screw.
(2) Turn the camera mounting base approx-
imately 15 degrees counterclockwise
and remove the base from the camera.
2. Setting the Switches
There are two DIP switches on the camera:
an 8-bit switch and a 4-bit switch. The 8-bit
DIP switch is used in both ways to return to
the factory default settings and to specify the
unit number. The 4-bit DIP switch selects ter-
mination ON/OFF and half/full duplex selec-
tion for RS485 communications. Switch set-
tings are read in to the camera when the
power is turned on. Make sure to turn it off,
then turn it back on after changing the
switch settings. Switch positions and func-
tions are shown below.
RS485 Parameter Setup
The selected protocol, communication para-
meters, and set unit numbers are read into
the camera when power is switched on.
1. Switch off the camera.
2. Set the switch according to the function
shown in the table.
3. Switch on the camera to read in the
changed switch settings.
4. Switch off the camera.
5. Set the unit number with the DIP switch
(see next page).
6. Switch on the camera to read in the
changed switch settings.
Note:The changed communication
parameters are displayed on the
RS485 SETUP menu after the cam-
era has been switched on.
Precautions
15°
Turn 15°
Then
Camera 
mounting base
Remove 
from the 
camera
1234 ON5678
Switch position
Returns to the factory default settings.
1234 ON5678
1234 ON5678
1234 ON5678
Switch positionBaud rate
1
1
1 None
None
None 8
8
8 19 200
  9 600
  4 800
Data bitParity 
checkStop 
bit
Parameter selection 
						

							44
Unit Number
Switch 1, an 8-bit DIP switch, specifies unit number or returns to
the factory default settings for Panasonic’s protocol.
When the switch position corresponding to the unit number 1-96*
is selected, setting should be made on the RS485 SET UP menu
(see page 40).
1234 ON5678
SW 1
For Panasonic’s Protocol
1234 ON5678
Switch positionUnit
number
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
Switch positionUnit
numberSwitch positionUnit
number
1-96*
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
2223
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
4546
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON567
8
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON56
78
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
(to be continued) 
						

							45
1234 ON5678
Switch positionUnit
number
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
Switch positionUnit
numberSwitch positionUnit
number
69
70
71
72
73
74
75
76
7778
79
80
81
82
83
84
85
8687
88
89
90
91
92
93
94
951234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678 
						

							46
Full duplex (4 line) *
BP 2
BP 1 Function
Switch
position
Function
Switch
position
RS485 Setting
The 4-bit DIP switch in used for
RS485 termination.
ON
Marking
1. Mark the mounting holes on the ceiling,
using the removed camera mounting base
as a template.
2. Fix the camera mounting base to the ceiling
with four screws (not provided, M4). Note:Remove sharp edges to protect the
cables.3. Assemble the Camera
Reverse the disassembly procedure. Take
care not to cut any cables.
OFFTermination ON
Termination OFF *
b. Top Cable Exit
Prepare a hole in the ceiling board to run the
cables.
1234 ON
SW 2
BP 3 BP 4
ON ON ON
OFF OFF OFFHalf duplex (2 line)
Notes:
•Defaults are marked with 
*.
•BP stands for Bit Position.
•Daisy chain connection is not available for
Full Duplex. (Only for Panasonic’s system
controllers)
Be sure to select a ceiling board strong
enough to support 4 times the total weight of
the camera.
Precaution
a. Sideway Cable Exit
Prepare a cutout in the diecast case and
decoration cover as shown in the following
figures.
Cutout in Diecast Case
Cutout in Decoration Cover 
						

							47
5. Tighten the fixing screw M3 (provided).
Notes:
(1) Tighten the camera fixing screw with a
screwdriver.
(2) Follow the instructions given here to
ensure that the camera and camera
mounting base are installed safely.
(3) When removing the camera from the
camera mounting base, loosen and
press up the camera fixing screw (M3)
by using a screwdriver.
6. Fix the decoration cover to the camera
mounting base.
a. Sideway Cable Exit
Pass the cables through the cutout made in
the diecast case and decoration cover.
b. Top Cable Exit
Push the decoration cover against the cam-
era mounting base.
15°
Be sure to match the wire with the fall 
prevention wire fixing angle as shown below.
Fall prevention
wire fixing angle Ring of the
fall prevention 
wire
Cautions:
•Use the supplied dust protection sheet if the
camera mounting base is liable to be
exposed to a dusty atmosphere. Remove the
cover from the dust protection sheet, then
stick the sheet on the camera mounting
base.
•Remove the sheet before mounting the cam-
era on the base.
•While the camera is separated from the
base, keep the camera in the supplied poly-
ethylene sack.
4. Mount the camera on the camera mounting
base and rotate the camera clockwise. 3. Hook the fall prevention wire on the camera
mounting base. 
						

							48
How to Assemble the Cable with the
Accessory Connector
Strip back the cable jacket approx. 3 mm (0.1
inch) and separate the individual conductors.
Recommended wire gauge sizes for 24 V AC line
#24
(0.22mm2) Copper wire size
(AWG)
Length
of cable
(approx.)(m)
(ft)#22
(0.33mm2)#20
(0.52mm2)#18
(0.83mm2)
20 30 45 75
65 100 160 260
Accessory Connector Information
Pin no. Power source
1
2
3
424 V AC LIVE
24 V AC NEUTRAL
Ground
Not use
ContactUp
Wire
Prepare the individual conductors for clamping.
Use MOLEX band tool part number 57027-5000
(for UL-Style Cable UL1015) or 57026-5000 (for
UL-Style UL1007) for clamping the contacts.
After clamping the contacts, push them into the
proper holes in the accessory connector of this
camera until they snap in place.
•Shrinking the cable-entry seal is a one-
time procedure. Do not shrink the cable-
entry seal until it has been ascertained
that the unit is functioning.
•CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY.
ContactInsert UpAApprox.
3 mm (0.1 inch)
Insert the wire until A position
and clamp the contacts.Wire
UpWire
Contact
Up
Contact
Wire
Approx.
3 mm (0.1 inch)
Insert the wire until A position
and clamp the contacts.
1 3
2 4
• 24 V AC Power Supply Connection
CAUTIONS Note:When powered up, the unit performs a self-check (including one panning, tilting, zooming and
focusing operation).
CONNECTIONS
• The following connections should be made by qualified service personnel or system installers in
accordance with all local codes.
• See the reverse side of the cover page for mains lead connection.
Precautions
✻The coaxial cable length (RG-59/U, BELDEN 9259) for the connec-
tion is up to 900 meters (3 000 ft.)To VIDEO IN
(CAMERA IN)
Video output24 V AC
BNC plugCoaxial cableRS485 cable
Data port
BNC plug
Not used
Not used24 V AC cable 
						

							49
• RS485 Connection
Note:
Use the cable that is described below for RS485 site communication.
•Shielded, twisted pair cable
•Low impedance
•Wire gauge size is thicker than AWG #22 (0.33 mm
2).
GND Brown
Red
Data transmission
Data receptionOrange
Yellow
Green
T (B)
T (A)
R (B)
R (A) 
						

							50
Note:When any peripheral is turned off and turned on again, the camera is also turned off and turned
back on.
SYSTEM CONNECTIONS
123456789MON CAM
ESC SET0ACK
RESETBACK
SEQFORWARD
SEQ ALTDEC
–1CAMINC
+1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS
NEAR ZOOM
TELE
FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP
DOWN
ALARMBUSYF3F4F2F1AF123456789MON CAM
ESC SET0ACK
RESETBACK
SEQFORWARD
SEQ ALTDEC
–1CAMINC
+1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS
NEAR ZOOM
TELE
FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP
DOWN
ALARMBUSYF3F4F2F1AF123456789MON CAM
ESC SET0ACK
RESETBACK
SEQFORWARD
SEQ ALTDEC
–1CAMINC
+1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS
NEAR ZOOM
TELE
FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP
DOWN
ALARMBUSYF3F4F2F1AF123456789MON CAM
ESC SET0ACK
RESETBACK
SEQFORWARD
SEQ ALTDEC
–1CAMINC
+1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS
NEAR ZOOM
TELE
FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP
DOWN
ALARMBUSYF3F4F2F1AF
Max. 64 cameras
VCRs (up to 16)
Monitors (up to 16) Printer
System controller Color CCTV camera
Matrix
switcher
Personal computer
RS-232C port
System status
monitor Alarm inputs 
						

							51
Zoom ratio
 




Bright object
SmearWhen the camera is aimed at a bright light, such
as a spotlight, or a surface that reflects bright
light, smear or blooming may appear. Therefore,
the camera should be operated carefully in the
vicinity of extremely bright objects to avoid
smear or blooming.
SPECIFICATIONS
PREVENTION OF BLOOMING AND SMEAR
Power source3.65 mm (H) x 2.71 mm (V), 1/4” 768 (H) x 494 (V)
Dimensions Focus speed  Effective pixels
15.724 kHz
F1.6 - 22, CLOSE Focal length
BLC
24 V AC, 60 Hz
120 (D) x 191 (H) mm
(4-3/4” (D) x 7-1/2” (H))
approx. 2 kg (4.4 lbs) −10°C - +50°C (14°F - 122°F) 14 W Power consumption
Ambient operating
temperature
Weight
selectable ON/OFF (SETUP MENU)
x 18 +digital zoom x2 internal/line-lock / multiplexed vertical drive (VD2)
59.94 Hz
1.0 V[p-p] NTSC composite/75 Ω
more than 480 lines at center (C/L)
more than 350 lines at center
50 dB (AGC OFF, weight on)
2.0 lx (0.2 foot-candle) (AGC HIGH)
approx. 4.5 s (TELE/WIDE) in manual mode
approx. 6.0 s (FAR/NEAR) in manual mode
automatic (open/close is possible)/manual
1 : 1.6 (WIDE) - 3.0 (TELE)
3.78 - 67.1 mm (17.8X)
3.2°- 51.7°
2.4°- 39.9°
1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s Scanning area
Synchronization
Horizontal scanning fre-
quency
Vertical scanning fre-
quency
Video output
Horizontal resolution
Vertical resolution
Signal-to-noise ratio
Minimum illumination
Zoom speed
Iris
Maximum aperture ratio
Angular field
of viewH
V
Electronic shutter
Iris range
ON (LOW)/ON (MID)/ON (HIGH)/OFF
AGC 
						

							52
Controls
Auto focus
Panning range
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.360°endless
possible (in auto-pan mode)
manual/sequential position/sort position/auto pan
manual : approx. 0.1°/s - 120°/s 8-steps/64-steps
sequence position : maximum approx. 300°/s
0°- 90°
manual/sequential position/sort position
manual : approx. 0.1°/s - 120°/s. 8-steps/64-steps
sequential position : maximum approx. 300°/s
pan/tilt, lens, 32 preset positions, home position Panning angle setting
Panning mode
Panning speed
Tilting range
Tilting mode
Tilting speed
ACCESSORIES
Decoration cover .............................................................. 1 pc.
Connector for 24 V AC  ..................................................... 1 pc.OFF/SEQ/SORT/AUTO PAN/PATROL
SEQ/SORT/AUTO PAN/PATROL PLAY
preset ID, camera ID: up to 16 characters
LEARN/PLAY/STOP, up to 30 seconds
ON/OFF Auto mode
Auto pan key
Camera ID
PATROL
Cleaning
OPTIONAL ACCESSORIES
Dome cover (approx. 60 % smoked type)  ............................................. WV-CS2S
Dome cover (approx. 50 % smoked type)  ............................................. WV-CS2SH
Dome cover (approx. 70 % metal type)  ................................................. WV-CS2MMANUAL/AUTO