Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

							32
Shutter Speed Setting (SHUTTER)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP menu on the monitor screen.
2. Move the cursor to SHUTTER and select the electronic shutter
speed by using the joystick. The factory default setting is OFF.
The electronic shutter speed changes as follows by operating the
joystick:
•When OFF is selected for BLC on the ALC CONT menu
Gain Control (AGC)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP menu on the monitor screen.
2. Move the cursor to AGC and select automatic level adjustment
ON (LOW), ON (MID), ON (HIGH) or fixed level (OFF) by using the
joystick.
The factory default setting is ON (MID).
ON (LOW):Selects lower gain control.
ON (MID):Selects normal gain control.
ON (HIGH):Selects higher gain control.
OFF (Fixed Level):Disables the gain control function.
Note:
•Even if AGC is set to ON and if the noise reduction function is
enabled, afterimages may be produced by shooting a moving
object or by panning or tilting the camera.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
OFF (1/60)1/100
1/10 0001/4 000 1/2 000 1/1 0001/2501/500 
						

							33
Synchronization (SYNC)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP menu on the monitor screen.
2. Move the cursor to SYNC and select line-lock (LL) or internal (INT)
by using the joystick.
The factory default setting is INT.
Important Notices:
1. The priority of SYNC modes is as follows:
1. Multiplexed vertical drive (VD2) (highest priority)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. To use internal sync, select INT.
3. Whenever the vertical drive pulse (VD2) is supplied to the cam-
era, the camera sync mode is automatically switched to the multi-
plexed vertical drive (VD2) regardless which sync mode is select-
ed.
Line-lock Sync Mode (LL)
1. Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP menu on the monitor screen.)
2. Move the cursor to SYNC and select LL by using the joystick. LL
sync mode is not available when the multiplexed vertical drive
(VD2) pulse is supplied.
3. After selecting LL, press the CAM (SET) key.
The SYNC menu appears on the monitor screen.
4. Supply the video output signal of the camera to be adjusted and
the reference camera video output signal to a dual-trace oscillo-
scope.
5. Set the dual-trace oscilloscope to the vertical rate and expand the
vertical sync portion on the oscilloscope.
6. Move the cursor to COARSE by using the joystick.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 LL  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
•|•••••••
-       +
SYNC menu 
						

							34
7. Use the joystick to match the vertical phases for both video output
signals as closely as possible. (COARSE adjustment can be
incremented in steps of 22.5 degrees (16 steps) with the joystick.)
Note:After the 16 steps, the adjustment returns to the first step.
8. Move the cursor to FINE by using the joystick.
9. Use the joystick to match the vertical phase for both video output
signals as closely as possible.
Notes:
•When the “|” cursor reaches the “+” end, it jumps back to “–”.
At the same time, COARSE is incremented by one step to
enable a continuous adjustment. The reverse takes place
when the “|” cursor reaches the “–” end.
•When the joystick is kept at the right or left for one second or
more, the “|” cursor moves quickly.
•To reset COARSE and FINE to the preset values at the facto-
ry, press the F2 button of the WV-CU550B. (For the WV-
RM70, press the Right and Left switches simultaneously.)
COARSE is preset at the factory to zero-crossing of the AC
line phase.
•If the AC line contains noise (spike noise, etc.), the stability of
the vertical phase of the camera video output signal may be
disturbed.
White Balance (WHITE BAL)
(1) Auto-Tracing White Balance Mode (ATW)
1. Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP menu on the monitor screen.)
2. Move the cursor to WHITE BAL and select ATW by using the joy-
stick. 
The factory default setting is ATW.
The white balance of the camera is automatically set.
3. For fine adjustment of the ATW, press the CAM (SET) key to dis-
play the ATW fine adjustment menu on the monitor screen.
4. Move the cursor to R.
Use the joystick to obtain the optimum amount of red gain. The “I”
cursor moves to the right or left.
5. Move the cursor to B.
Use the joystick to obtain the optimum amount of blue gain. The
“I” cursor moves to the right or left.
6. Move the cursor to RET by using the joystick and press the CAM
(SET) key to return to SET UP.
1(1--16)
-       +
      ** SYNC **
V PHASE
COARSE
FINE
RET
      ** SYNC **
V PHASE
COARSE
FINE
RET4(1--16)
••••••|••
-       +
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
•|•••••••
-       +
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
      **  ATW  **
R
B
RET••••|••••
-       +
••••|••••
-       +
ATW fine adjustment menu
1 (1 - - - 16): 0 degrees
2 (1 - - - 16): 22.5 degrees
16 (1 - - - 16): 337.5 degrees 
						

							35
(2) Automatic White Balance Control Mode (AWC)
1. Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP menu on the monitor screen.)
2. Move the cursor to WHITE BAL and select AWC →PUSH SW by
using the joystick.
3. Press the CAM (SET) key to start the white balance setup. PUSH
SW is highlighted to indicate that white balance is being set.
4. PUSH SW returns to normal when balance setting is completed.
5. For fine adjustment of the AWC, move the cursor to select AWC
and press the CAM (SET) key to display the AWC fine adjustment
menu on the monitor screen.
6. Move the cursor to R.
Use the joystick to obtain the optimum amount of red gain. The “I”
cursor moves to the right or left.
7. Move the cursor to B.
Use the joystick to obtain the optimum amount of blue gain. The
“I” cursor moves to the right or left.
8. Move the cursor to RET by using the joystick and
press the CAM (SET) key to return to SET UP.
      **  AWC  **
R
B
RET••••|••••
-       +
••••|••••
-       +
AWC fine adjustment menu
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 AWC   
 MANUAL S  
 ON
 OFF
Camera setting menu
Blue sky
Cloudy
Fine AWC
10000 K
Bluish
Reddish
9000 K
8000 K
7000 K
6000 K
5000 K
4000 K
3000 K
2000 K
1000 KATW
Halogen lamp
Rainy
Partly cloudy
Fluorescent
lamp
Tungsten
lamp
Candle 
						

							36
Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the following mode by
moving the joystick to the right or left.
The factory default setting is MANUAL S.
S, M and L stand for Small, Middle and Large areas in the center
of a scene that are used for sensing sharpness in auto-focusing.
MANUAL S, M, L:Brings the camera into focus when the AF key
on the controller is pressed.
AUTO S, M, L:Brings the camera into focus while operating pan,
tilt or zoom manually. These may be selected in the same way
as selecting MANUAL by pressing the AF key on the con-
troller.
2. To confirm auto-focus operation, press CAM (SET) key while the
cursor is at AF MODE.
Notes:
•The auto focus lens does not function properly in AUTO after
using WIDE lens.
•The auto focus lens may not function properly in AUTO under the
following conditions.
1. Dirt or water on window glass.
The auto focus may focus on the dirt or water.
2. Low lighting/illumination or zone marker is blinking.
3. Bright objects or high intensity objects.
4. Single color with unfigured object such as white wall or fine
felt.
5. No center objects, sloping objects.
6. Far and near objects on the screen.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
AUTO SAUTO M AUTO L
MANUAL L MANUAL M MANUAL S 
						

							37
Electronic Zoom (EL-ZOOM)
The electronic zoom magnifies a scene 2-fold. With a 18-fold optical
zoom lens, the camera is capable of 36-fold zoom.
1. Move the cursor to EL-ZOOM and select ON or OFF by moving
the joystick to the right or left, and then press the CAM (SET) key.
The factory default setting is ON.
ON:Two (2) - fold electronic zoom is available with the ZOOM
switch on the controller.
OFF:The electronic zoom function is not used.
Notes:
•A scene magnified by the electronic zoom function may be
inferior to a non-magnified one in picture quality.
•The electronic zoom does not function in preset position set-
ting mode.
•To set preset position directly from the WV-CU360 System
Controller, it is temporarily required setting the electronic
zoom function to OFF.
Image Hold (IMAGE HOLD)
The camera picture remains as a still image on the monitor screen
until the camera reaches the preset position. This function is useful for
surveillance via local area network.
1. Move the cursor to IMAGE HOLD and select ON or OFF.
The factory default setting is OFF.
ON:The last displayed still image is shown till the camera finishes
moving to a preset position. However, the still image may be
distorted with the effect of panning or tilting.
OFF:The current image is being displayed while the camera is
moving to a preset position.
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu 
						

							38
 Special Menu (SPECIAL)
This menu lets you adjust and set up the picture quality to meet your
requirements.
•Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP on the monitor screen.)
•Move the cursor to SPECIAL and press the F2 button of the WV-
CU550B. The special menu appears on the monitor screen.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)
(1) Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN. The “I” cursor is highlighted.
2. While observing the vectorscope or color video monitor, adjust
the chroma level by using the joystick. The “I” cursor moves to the
right or left.
To reset to the factory setup, press the F2 button of the WV-
CU550B.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)
(2) Aperture Level Setting (AP GAIN)
1. Move the cursor to AP GAIN. The “I” cursor is highlighted.
2. While observing the video monitor, adjust the aperture level with
the joystick. The “I” cursor moves to the right (sharp) or left (soft).
To reset to the factory setup, press the F2 button of the WV-
CU550B.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)
(3) Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL. The “I” cursor is highlighted.
2. While observing the waveform monitor/oscilloscope or video mon-
itor, adjust the pedestal level (black level) by moving the joystick.
The “I” cursor moves to the right (high, bright) or left (low, dark).
To reset to the factory setup, press the F2 button of the WV-
CU550B.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)
(4) Chroma Phase (Hue) Setting (HUE)
1. Move the cursor to HUE The “I” cursor is highlighted.
2. While observing the vector scope or a color video monitor, adjust
the chroma phase by moving the joystick. The “I” cursor moves to
the right or left.
To reset to the factory setup, press the F2 button of the WV-
CU550B.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW
Special  menu
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW 
						

							39
(5) To Restore the Camera Default Position (REFRESH)
Move the cursor to REFRESH by using the joystick and press the
F2 button of the WV-CU550B.
(For the WV-RM70, WV-CU360 or WV-CU161, keep pressing the
Right and Left switches simultaneously for 2 seconds or more.)
(6) Camera Resetting (CAMERA RESET)
Move the cursor to CAMERA RESET by using the joystick and
press the F3 button of the WV-CU550B.
The camera is reset to the factory preset parameters.
(For the WV-RM70, keep pressing the Right, Left and Set switches
simultaneously for 2 seconds or more. For the WV-CU360 or WV-
CU161, keep pressing the Right and Left switches and the numer-
ic button 5 simultaneously for 2 seconds or more.)
(7) To Close the SPECIAL Menu
Move the cursor to RET and press the CAM (SET) key.
The setup menu appears on the monitor screen.
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW
     ** SPECIAL **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
REFRESH
CAMERA RESET
RET••••|••••
••••|••••
•|•••••••
••••|••••
-       +
→PUSH SW→PUSH SW 
						

							40
How to Reset to the Factory Preset Parameters
Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the
factory preset parameters by placing the cursor over the desired mode and then press the F2 button of
the WV-CU550B. (For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 sec-
onds or more.)
RS485 Setup
Initial Camera Communication Parameters
In an RS485 chain the matrix switcher, PC, controllers and cameras should be set to the same protocol
and parameters for communication. Confirm the system protocol and parameters prior to setting the com-
munication parameters for the camera.
The initial communication parameters are shown on the RS485 setup menu below. Other than the on-
screen-setup parameters, the 4-bit DIP switch may be used to select 2-line (Half Duplex) or 4-line (Full
Duplex) communication.
Changing the Camera Communication Parameters
You can remote control this camera by using a specified extension
unit such as a computer with a modem.
1. Display the SET UP MENU. Move the cursor to RS485 SET UP
and press the CAM (SET) key. RS485 SET UP menu appears on the
monitor.
2. Move the cursor to the item and select the parameter by moving the
joystick to the right or left.
Unit Number (UNIT NUMBER)
Displays the unit number set by the DIP switch. If the switch is set to 1-96, select a number by moving the
joystick to the right or left. In an RS485 chain each unit must have a unique number.
Default: 1. See INSTALLATION for DIP switch setting.
Sub Address (SUB ADDRESS)
Do not set.
Baud Rate (BAUD RATE)
Specifies the transmission speed (2 400, 4 800, 9 600, 19 200 bit per second) for the RS485 communica-
tion. The factory setting is 19 200.
Data Bit (DATA BIT)
Specifies the number of data bits (7 or 8 bits) for the RS485 communication. The factory setting is 8.
Parity Check (PARITY CHECK)
Specifies the parity check mode (NONE, ODD, EVEN). The factory setting is NONE.
Stop Bit (STOP BIT)
Specifies the number of stop bits (1 or 2 bits). The factory setting is 1.
   ** RS485 SET UP ** 
UNIT NUMBER
SUB ADDRESS 
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET1
-----
19200
8
NONE
1
NOT USE
OFF
---
---
RS485 Setup menu 
						

							41
X ON/X OFF (X ON/X OFF)
Specifies whether to apply flow control or not (NOT USE, USE). The factory setting is NOT USE.
Wait Time (WAIT TIME)
Specifies the time to wait until retrying after confirming that no data is received from the controller.
(OFF: no retry, 100, 200, 400, 1 000 ms).
The factory setting is OFF.
Delay Time (DELAY TIME)
Specifies the time to transmit the acknowledge request when communicating on a 2-line connection.
[----,100 ms] Default: ---- (no set).
This menu appears only when a 2-line communication is used. Make sure to be 100 ms when connecting
the camera with the WJ-FS616 Video Multiplexer or Matrix Switcher WJ-SX350 in a 2-line communication
system.
The settings become effective with the closing of the SET UP MENU.
Note:Set the same parameters for the cameras, controllers and personal computers in an RS485 chain.