Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

							22
Deleting Preset Positions
1. Move the cursor to PRESET 1* and select the position number to
be deleted by using the joystick.
2. Press the CAM (SET) key to display the preset setting menu.
3. Move the cursor to DEL and press the CAM (SET) key.
This deletes the preset position and the PRESET NUMBER SET
menu appears. The * mark on the right of the number disappears.
Note:Your selected preset number is cancelled only in the SEQ
and SORT mode. The previously set parameters (for PAN,
TILT positions, etc.) are not changed. If you want to change
these parameters, you must set them again.
Home Position Setting
(HOME POSITION)
1. To set a position number for the home position
Move the cursor to HOME POSITION and select the desired posi-
tion number by moving the joystick to the right or left.
The factory default setting is OFF.
2. Select OFF if you are not using the home position function.
Note:This setting functions only when AUTO MODE is set to OFF.
Self Return Setting (SELF RETURN)
1. To set a time-out parameter for return to the home position
Move the cursor to SELF RETURN and select a return time by
moving the joystick to the right or left.
The factory default setting is OFF.
Return time changes as follows:
2MIN 3MIN 5MIN 10MIN
60MIN
30MIN 20MIN1MIN
OFF
MIN stands for minute(s).
Note:The camera will return to the auto mode if that is set to SEQ,
SORT, AUTO PAN or PATROL when a specific time has
elapsed after a manual operation.
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu
   ** SET UP MENU **
PRESET 1* 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
 ** PRESET NUMBER SET **
  2
  6
 10
 14
 18
 22
 26
 30   1
  5
  9
 13
 17
 21
 25
 29
   ID:DOOR
RET  3
  7
 11
 15
 19
 23
 27
 31  4
  8
 12
 16
 20
 24
 28
 32
PRESET NUMBER SET menu
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UP15
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
10MIN
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu 
						

							23
Auto Mode Selection (AUTO MODE)
1. To set auto mode
Move the cursor to AUTO MODE and select a mode by moving
the joystick to the right or left.
The factory default setting is OFF.
Modes change as follows:
OFF:No automatic operation. The camera can be operated only
manually.
SEQ:The camera operates in the sequence of preset positions in
numerical order.
SORT:The camera operates in the sequence of preset positions
counterclockwise from Pan Starting Point.
AUTO PAN:The camera automatically turns within the preset
panning range.
PATROL:The camera operates in the patrol learn function.
2. When the AUTO PAN mode is selected, set details as follows:
Move the cursor to AUTO PAN  and press the CAM (SET) key
to display the AUTO PAN setting menu.
3. To set a panning starting point and panning endpoint
Follow the steps below.
(1) Move the cursor to POSITION and press the CAM (SET) key.
The cursor moves to START.
(2) Move the joystick to the right or left to select a panning start-
ing point and press the CAM (SET) key.
This determines the starting point and the cursor moves to
END.
(3) Move the joystick to the right or left to select a panning end-
point and press the CAM (SET) key.
This determines the endpoint and the cursor moves to POSI-
TION.
4. To set a panning speed
Move the cursor to SPEED, and move the joystick to the right or
left to set a panning speed.
The panning speed increases when the joystick is moved to the
right, and decreases when it is moved to the left.
Caution:If the panning range is changed after the camera has not
panned for a long time or has been panning in the same panning
range, the picture may not be clear or noise may appear. In this
case, pan the camera fully several times.
If this does not eliminate the problem, refer servicing to qualified
service personnel.
OFFSEQSORTAUTO PAN PATROL
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
    ** AUTO PAN **
POSITION 
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
¥¥¥¥|¥¥¥¥
L       H
OFF
OFF
1S
AUTO PAN setting menu
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
OFF
1S
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
OFF
1S
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
OFF
1S 
						

							24
5. To set pan limit ON/OFF
Move the cursor to PAN LIMIT and select ON or OFF by mov-
ing the joystick to the right or left.
The factory default setting is OFF.
ON:Manual pan is limited from the starting point to the end-
point specified by position setting. Set ENDLESS to OFF
before PAN LIMIT is set to ON.
OFF:Manual pan is not limited.
Note:When ON is selected for PAN LIMIT, manual pan moves the
camera away from the other side (PAN LIMIT) of the start-end
range.
6. To set ENDLESS to ON/OFF
Move the cursor to ENDLESS, and move the joystick to the right or
left.
The factory default setting is OFF.
ON:The camera pans from the starting point to the endpoint, and
keeps rotating in the same direction to return to the starting
point. Set PAN LIMIT to OFF before ENDLESS is set to ON.
OFF:The camera pans from the starting point to the endpoint,
and rotates backward to the starting point.
This movement is repeated over and over.
7. To set a dwell time
Move the cursor to DWELL TIME and select a dwell time by mov-
ing the joystick to the right or left.
The factory default setting is 1S.
Dwell time changes as follows:
Notes:
•When the panning, tilting, zooming or focusing in the SEQ,
SORT or PATROL mode is controlled manually, the Auto
mode function should be cancelled.
To activate the auto mode, select the desired auto mode
again or set a time for SELF RETURN in the SET UP menu.
•When 0S is selected, the camera stops without dwelling and
starts.
•Auto refreshing may be activated during the patrol play or the
auto mode to calibrate the lens position.
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
ON
1S
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
OFF
1S
0S
1S2S3S
30S 5S10S20S
Camera Endpoint
Starting point Start-end
range of
auto panSelf-end 
range of
pan limit 
						

							25
Auto Pan Key Setting
(AUTO PAN KEY)
This is used for assigning one of the following auto functions to the
AUTO key on the controller. Pressing the AUTO key activates the
assigned function after this setting.
•Move the cursor to AUTO PAN KEY and select an auto function by
moving the joystick to the right or left.
The factory default setting is AUTO PAN.
Mode changes as follows:
AUTO PAN:assigns auto panning function to the key.
SEQ:assigns the sequence function to the key.
SORT:assigns the sort function to the key.
PATROL:assigns the patrol play function to the key.
Note:Auto pan LED on the controller does not light if a function
other than the auto pan function is assigned. The auto pan
function does not stop with the AUTO PAN key.
Local/Remote Setting
(LOCAL/REMOTE)
•Move the cursor to LOCAL/REMOTE, and move the joystick to the
right or left.
The factory default setting is LOCAL.
You can toggle between LOCAL and REMOTE.
Note:The REMOTE does not work when the WV-RM70, WV-
CU360, WV-CU161, WJ-FS616 or WV-CU550 series is con-
nected. Make sure that LOCAL is selected in this case.
AUTO PANSEQ SORT
PATROL
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu 
						

							   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Special 1 menu
26
 Patrol Learn and Patrol Play
(PATROL)
A routine of manual operations can be stored for 30 seconds at the
maximum and reproduced repetitively.
1. Set the following parameters for the patrol learn starting position.
These parameters are stored when the patrol learn mode starts.
•PAN/TILT/ZOOM/FOCUS
•IRIS
•SHUTTER
•AGC
•WHITE BALANCE
•IMAGE HOLD
•CAMERA ID
•PAN LIMIT
•CLEANING
After starting the patrol learn, the following manual operations are
stored.
•PAN/TILT/ZOOM/FOCUS operation
•IRIS operation
•Preset positioning
2. Open the SET UP menu and move the cursor to PATROL. Select
LEARN, PLAY or STOP for PATROL by moving the joystick to the
right or left.
The factory default setting is STOP.
LEARN: A series of manual operations is stored.
PLAY:Stored operations are reproduced.
STOP:LEARN or PLAY is not activated.
Patrol Learn with a Controller Having the PATROL Key
1. Press the PATROL LEARN key and the PROGRAM key simultane-
ously to start the patrol learn. The setup menu changes to show
“LEARNING” and the starting points are stored.
2. Operate the patrol learn manually. The operation data is stored.
3. To stop the patrol learn, press the PATROL STOP key and the
PROGRAM key simultaneously. 
						

							27
Patrol Learn with a Controller not Having the PATROL Key
1. Select the patrol learn in the setup menu, and then close it.
Starting points are stored and “LEARNING” appears on the moni-
tor screen.
2. Operate the patrol learn manually.
3. Open the SET UP menu to stop learning.
Notes:
•It is recommended that you set PAN LIMIT to ON for the
patrol learn. Otherwise PAN LIMIT is invalid for playback.
•Start the patrol learn function again from the starting point, If
the power has failed during the patrol learn mode.
•LEARN also stops 30 seconds after starting if the memory is
full.
•Auto refreshing may be activated during the patrol play mode
or the auto mode to calibrate the lens position.
Patrol Play with a Controller Having the PATROL Key
1. Press the PATROL PLAY key. The camera turns to the starting
point and the operations stored in the memory are reproduced.
Iris operation is only accepted during playback.
2. Press the PATROL STOP key and PROGRAM key simultaneously
to stop playback or press any manual operation key (e.g.,
PAN/TILT/ ZOOM/FOCUS) except the iris keys.
Patrol Play with a Controller not Having the PATROL Key
1. Select the patrol play in the setup menu, and then close it. The
camera turns to the starting point and the operations stored in the
memory are reproduced. Iris operation is only accepted during
playback.
2. Open the SET UP menu, or press any manual operation key (e.g.,
PAN/TILT/ ZOOM/FOCUS) except the iris keys to stop playback.
Patrol Play with the AUTO PAN Key
1. If the PATROL PLAY function is assigned to the AUTO PAN key,
press the AUTO PAN key to turn the camera back to the starting
point and to reproduce the operation data stored in the memory.
2. Press the PATROL STOP key and PROGRAM key simultaneously
or any manual operation key (e.g., PAN/TILT/ZOOM/FOCUS)
except the iris keys to stop playback.
Notes: 
•During the patrol play mode, the camera movement may occa-
sionally deviate from the entered routine when the routine
includes a move to a preset position. If this happens, re-enter the
routine of manual operations in the patrol learn.
•During the patrol play mode, black and white automatic switching
does not work.
•During the patrol play mode, when the power of the controller is
turned on or off, the patrol play stops. In this case, press the
PATROL PLAY key again. (If SELF RETURN is set to ON, the
patrol play will start again after elapsing the setting return time.)
LEARNING
PATROL LEARN 
						

							28
 Cleaning (CLEANING)
Built-in electric mechanical contacts are refreshed at regular
intervals (approx. 7 days) if CLEANING is set to ON.
A dry contract affects adversely picture quality and motors oper-
ation.
1. Move the cursor to CLEANING and select ON or OFF by moving
the joystick to the right or left.
The factory default setting is OFF.
ON:The contacts are cleaned as programmed for about 1
minute. “CLEANING” disappears when it is over.
OFF:No contact cleaning.
Note:Select OFF when the camera downloads or uploads the
preset data.
Camera Setting
To Display the Camera Setting Menu
•Move the cursor to CAMERA  , and press the CAM (SET) key.
The camera setting menu appears.
Camera Identification (CAMERA ID)
1. Move the cursor to CAMERA ID, and select ON (to display the
camera identification) or OFF by using the joystick.
The factory default setting is OFF.
2. Follow the steps below to edit the camera ID characters:
2-1 Move the cursor to CAMERA ID and press the CAM (SET)
key to display the character editing menu.
2-2 Move the cursor to the character you want to edit or change
by using the joystick, and press the CAM (SET) key. The
selected character appears in the editing area.
2-3 Repeat the steps above until all characters are edited.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Special 1 menu
CLEANING
CLEANING
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    OFF 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF 
						

							29
3. After editing the camera identification characters, follow the steps
below to set the position of the CAMERA ID on the monitor screen.
3-1 Move the cursor to POSI, and press the CAM (SET) key to display
the ID position menu.
3-2 Use the joystick to decide the position of the CAMERA ID on the
monitor screen. Press the MON (ESC) key to fix the position, and
return to the character editing menu.
Notes:
•When you want the pointer to move to a specific character in the
editing area, select a new character, and press the CAM (SET)
key. This function allows you to edit or correct a specific charac-
ter.
•When you want a blank space in the CAMERA ID, move the char-
acter cursor to SPACE, and press the CAM (SET) key.
•When you want to erase all characters in the editing area, move
the cursor to RESET and press the CAM (SET) key.
•The positioning of the CAMERA ID stops at the edges of the
screen.
•The CAMERA ID moves faster when the joystick is kept at the
right or left for one second or more.
•To return to SET UP for setting other items, move the cursor to
RET, and press the CAM (SET) key.     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
CAM1 
						

							30
Light Control Setting (ALC/MANUAL)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP on the monitor screen.
2. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
using the joystick.
The factory default setting is ALC.
When you select ALC, set backlight compensation.
Note:The backlight compensation submenu associated with this
menu is described separately and should be set up after
installing the camera at the site and observing the actual site
picture.
3. When MANUAL is selected, quit the setup menu by pressing
MON (ESC) key. Press OPEN or CLOSE key on the controller for
iris adjustments by manual.
(1) ALC Mode with BLC ON
1. Press the CAM (SET) key after selecting ALC. The ALC CONT
menu appears.
2. Move the cursor to the BLC and select ON.
3. If you want to adjust the video output level, move the “I” cursor for
LEVEL. Adjust to the desired level by using the joystick.
4. Move the cursor to RET and press the CAM (SET) key to return to
the CAM SET UP menu. (To return to the camera picture, press
the F4 button.)
     ** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SYNC
WHITE BAL
AF MODE
EL-ZOOM
IMAGE HOLD
RET     SPECIAL    ON 
 ALC 
 OFF
 ON(MID)
 INT  
 ATW   
 MANUAL S  
 ON
 OFF
Camera setting menu
    ** ALC CONT **
    BACK LIGHT COMP
BLC
 
LEVEL
RETON
••••|••••
-       +
    ** ALC CONT **
    BACK LIGHT COMP
BLC
MASK SET 
LEVEL
RETOFF
••••|••••
-       +
Backlight compensation menu 
						

							31
(2) ALC Mode with BLC OFF
1. Move the cursor to the BLC and select OFF. (When you select
MANUAL, BLC is not available.) The MASK SET appears on the
menu.
2. Move the cursor to MASK SET and press the CAM (SET) key. The
48 mask areas appear on the monitor screen. The cursor is blink-
ing in the top left corner of the screen.
3. To mask an area where backlight is bright, move the cursor to that
area and press the CAM (SET) key. The mask turns to white.
Repeat this procedure to mask the desired area.
4. To cancel a masked area, move the cursor to that area, and press
the CAM (SET) key. To cancel all masking area, press the F2 but-
ton of the WV-CU550B. (For the WV-RM70, press the right and left
switches simultaneously.)
5. After masking is completed, press the MON (ESC) key. The 48
mask areas on the monitor screen disappear and the ALC CONT
menu appears.
6. If you want to change the video output level (picture contrast),
move the “I” cursor for LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM (SET) key to return to
the CAM SET UP menu. (To return to the camera picture, press
the F4 button.)
Blinking
Blinking
Blinking
Turns to white
    ** ALC CONT **
    BACK LIGHT COMP
BLC
MASK SET 
LEVEL
RETOFF
••••|••••
-       +
    ** ALC CONT **
    BACK LIGHT COMP
BLC
MASK SET 
LEVEL
RETOFF
••••|••••
-       +