Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

							12
Auto Pan Key (AUTO PAN KEY)
This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the con-
troller.
After setting this, the AUTO key performs as assigned.
Note:The AUTO PAN LED on the controller does not light if the mode other than the AUTO PAN mode is
assigned.
Local/Remote (LOCAL/REMOTE)
This setting determines whether the camera continues or stops the ongoing auto operation when the con-
troller is turned off.
LOCAL:The camera continues operating in the auto mode when the controller is turned off.
REMOTE:The camera stops operating in the auto mode approx. 1 minute after the controller is turned
off.
See page 25 for the setting.
Patrol Learn and Patrol Play (PATROL)
A set of manual operations is stored (LEARN), reproduced (PLAY) or turned inactive (OFF). Patrol
operation stops if SEQ, SORT or AUTO PAN is set to AUTO MODE on the SETUP menu. See page 26
for details. 
						

							13
Cleaning (CLEANING)
This is used for refreshing the electric-mechanical contacts built in the camera. Use this function for
maintenance when the camera has been directed to a specific spot or panned over a specific range
for a long time.
Image Hold (IMAGE HOLD)
The camera picture remains a still image on the monitor screen or until the camera reaches the pre-
set position. This function is useful for surveillance via a local area network.
Camera
(1) Camera Identification (CAMERA ID)
You can use the camera identification to assign a name to the camera. The camera ID consists of up
to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the moni-
tor screen or not. See page 28 for the setting.
(2) Light Control (ALC/MANUAL)
You can select the mode for adjusting the lens iris. There are two modes as follows:
ALC:The lens iris is automatically adjusted according to the brightness of the object.
You can select one of two modes (BLC ON or BLC OFF) of backlight compensation.
Backlight compensation is available for the ALC mode. It eliminates strong background light
which makes the camera picture dark such as a spotlight.
MANUAL:The lens iris is fixed at the value that you have set regardless of the brightness of the
object.
• ALC Mode with BLC ON
An important object in a scene is usually placed in the center of the monitor screen. By the setup,
more photometric weight is given to the center of the screen than to the edge of the screen (where
bright backlight would most likely be located). In such a case, the object at the center of the screen
can be still clearly seen even though the backlight may vary.
See page 30 for the setting.
• ALC Mode with BLC OFF
This mode is effective when a main object in the scene is not located in the center of the screen but a
source of bright light is located near the center of the scene. In this mode, the picture is divided into
48 areas that mask the light to keep the clarity of the picture. 
						

							14
Note:The result of field setup of the mask area and level adjustment is fed back (effected) to the lens
iris control in ALC mode.
(3) Shutter Speed (SHUTTER)
You can select a shutter speed of 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and
1/10 000 seconds.
See page 32 for the setting.
(4) Gain Control (AGC)
You can set the gain (brightness level portion of an image) to automatic adjustment [Automatic Gain
Control ON (LOW, MID, HIGH)] or fixed (Automatic Gain Control OFF).
See page 32 for the setting.
(5) Synchronization (SYNC)
You can select the internal sync (INT) mode or the line-lock sync (LL) mode. Additionally, this model
accepts the VD2 signal (multiplexed vertical drive signal with the composite video output signal) from
a specified component. Whenever the VD2 signal is supplied to this camera, the camera automatical-
ly switches to the VD2 sync mode.
When you select the line-lock sync (LL) mode, you can set vertical phase adjustment.
See page 33 for the setting.
Important Notices:
The priority of sync modes is given as follows:
1. Multiplexed vertical drive (VD2) (highest)
2. Line-lock (LL)
3. Internal sync (INT) (lowest)
Note:The priority of the automatic sync mode is the same as shown above. 
						

							15
(6) White Balance (WHITE BAL)
You can select one of two modes for white balance adjustment as follows:
• Auto-Tracing White Balance (ATW)
In this mode, the color temperature is monitored continuously and thereby white balance is set auto-
matically. The color temperature range for the proper white balance is approx.2 600 - 6 000 K. Proper
white balance may not be obtained under the following conditions:
1. The color temperature is out of the 2 600 - 6 000 K range.
2. When the scene contains mostly high color temperature (bluish) objects, such as a blue sky.
3. When the scene is dim.
In these cases, select the AWC mode.
• Automatic White Balance (AWC)
In this mode, accurate white balance is obtained within a color temperature range of approx. 2 300 -
10 000 K.
See page 34 for the setting.
(7) Auto Focus (AF MODE)
The camera adjusts the focus automatically by sensing sharpness in the center of the picture. S, M
and L stand for the breadth of the sensing area: Small, Middle and Large.
See page 36 for details.
MANUAL S, M, L:Auto-focus is activated when the AF key on the controller is pressed.
AUTO S, M, L:Auto-focus is activated automatically while operating manually: pan, tilt or zoom.
(8) Electronic Zoom (EL-ZOOM)
Up to 2-fold electronic zooming is available besides 18-fold optical zooming.
(9) Image Hold (IMAGE HOLD)
The camera picture remains a still image on the monitor screen until the camera reaches the preset
position. This function is useful for surveillance via a local area network.
(10) Special  Menu (SPECIAL)
This menu allows you to adjust and set up the following items and functions: chroma level, aperture
level, pedestal level, hue adjustment and refresh function.
You can also reset your parameters to the values preset at the factory.
See page 38 for the setting.
RS485 communication
Camera communication parameters
See the following items pages for the setting.
• Full/Half duplex (page 46)
• Transmission Speed (2 400 - 19 200 bps) (page 40)
• Parity bit, Stop bit, Flow control (pages 40 and 41)
• Wait time, Delay time (page 41)
• Camera units (96 units max.) (page 44)
• Termination ON/OFF (page 46)
• Reset parameters (page 43) 
						

							16
SETTING PROCEDURES
The following setting procedures are described on the assumption that this model is used in combination
with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case of using a controller
other than the WV-CU550B, refer to the table on page 10.
Menu Display
Setup Menu Display
WV-CU550B
1. Select the camera number you want to set up and a monitor to
display the SET UP MENU.
2. Display the D4 menu on the LCD by pressing the appropriate cur-
sor buttons.
3. Press the F1 button.
The SET UP MENU appears on the monitor screen.
4. To close the SET UP MENU, press the F4 button.
WV-CU360
Press the CAM SETUP key for 2 seconds or more to open the
SETUP menu.
WV-CU161
Press the CAMERA SETUP key for 2 seconds or more to open the
SETUP menu.
WV-RM70
1. Turn the MODE SELECTION switch to NORMAL or ALARM OFF.
2. Press the PROG switch for 2 seconds or more to open the
Program Menu.
3. Move the cursor to Camera Set Up Menu, and press the SET
switch to open the SETUP MENU.
Submenu Display
The items marked  can be selected/changed on the submenu.
• Move the cursor to an item with the  mark and press the CAM
(SET) key. The submenu appears.
D4 menu
F1
F1 F2F3F4
Camera Set Up Menu
      Res A.Res Exit
F2F3F4
Camera Set Up Menu
 On             Exit
   ** RS485 SET UP ** 
UNIT NUMBER
SUB ADDRESS 
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET1
-----
19200
8
NONE
1
NOT USE
OFF
---
---
Submenu
(for RS485 setup)
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu 
						

							17
Presetting
Preset Menu Display
1.Displaying the preset menu directly
(1) Move the cursor to PRESET 1  and move the joystick to the
right or left to select the position number to be set.
(2) Press the CAM (SET) key.
The preset setting menu appears on the monitor screen.
2.Displaying the preset menu from the PRESET NUMBER SET menu
(1) Move the cursor to MAP  and press the CAM (SET) key.
The PRESET NUMBER SET menu appears on the monitor
screen.
(2) Move the cursor to the position number to be set and press
the CAM (SET) key.
Notes:
• The * mark means that the position number has been preset.
• The character H means the home position.
• On the second bottom line, the preset ID appears respective
to the selected number. “DOOR” next to “ID” is for preset
position number 1 in the example shown right.
Position Setting (POSITION SET)
1.Move the cursor to POSITION SET on the preset setting menu and
press the CAM (SET) key.
The position setting menu appears.
2. To Set Panning/Tilting Positions
(1) Move the cursor to PUSH SET for PAN/TILT and press the
CAM (SET) key. The PAN/TILT setting menu appears.
(2) Select panning/tilting positions by moving the joystick up and
down, right and left, and press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
 ** PRESET NUMBER SET **
  2
  6
 10
 14
 18
 22
 26
 30   1
  5
  9
 13
 17
 21
 25
 29
   ID:DOOR
RET  3
  7
 11
 15
 19
 23
 27
 31  4
  8
 12
 16
 20
 24
 28
 32
PRESET NUMBER SET menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF 
••••••••|
L       H
Preset setting menu
→PUSH SET→PUSH SET
    ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET 
←   −0.0 →
RET
FLOOR1
DOOR
Position setting menu
→PUSH SET→PUSH SET     ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
   U TILT D/L PAN R
PAN OFFSET SET ←   −0.0 →
RET
FLOOR1
DOOR
   ** SET UP MENU **
PRESET 1* 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Setup menu
PAN/TILT setting menu 
						

							18
3. Pan Offset
If the camera is replaced with a new one, the pan offset function
is used to adjust its positions to be the same as before except
patrol setting.
The controller can be downloaded or uploaded the preset posi-
tion data.
Caution:The preset data for other camera models (WV-CS650 for
example) is incompatible with WV-CS564s.  WV-CS564s pre-
set data will be destroyed if you upload the conventional
data. If this happened, reset the WV-CS564 to the default set-
tings. Download the factory settings into the controller and
upload the correct preset data newly to the initialized WV-
CS564.
(1) Display the PRESET NUMBER SET menu.
(2) Select a position number for the picture to be most enlarged
among the numbers by using the joystick. Then press the
CAM (SET) key. The position setting menu appears.
(3) Move the cursor to PAN OFFSET SET and select the right or
left arrow by moving the joystick.
(4) Press the CAM (SET) key until the desired offset value
appears.
(5) Move the cursor to other than PAN OFFSET SET, and press
the MON (ESC) key.
Notes:
• Further adjustment of the other positions is unnecessary. This
adjustment applies to all other positions.
• Make sure to move the cursor before pressing the key in step
5. Otherwise the settings will be ignored.
• Retry when the camera fails to upload or download the data.
4. To Set the Lens Zoom and Focus Positions
(1) Move the cursor to PUSH SET for ZOOM/FOCUS and press
the CAM (SET) key. The ZOOM/FOCUS setting menu
appears.
(2) Select a zoom position by moving the zoom control up and
down, and a focus position by moving the focus control up
and down, and then press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
Notes:
• When the camera is used at a nearly horizontal angle, the
focus may not be adjustable to a high level of accuracy.
• If you move the cursor to the position number and move
the joystick right or left, the position number can be
selected.
The selected preset position number can also be set after
pressing the CAM (SET) key.
• The preset and camera IDs appear at the lower-left cor-
ner of the position setting menu after setting them.
5.Move the cursor to RET and press the CAM (SET) key to return to
the preset setting menu.
→PUSH SET→PUSH SET
    ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET 
←   −0.0 →
RET
FLOOR1
DOOR
Position setting menu
    ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
   U ZOOM D/L FOCUS R
PAN OFFSET SET ←   −0.0 →
RET
FLOOR1
DOOR
→PUSH SET→PUSH SET
→PUSH SET→PUSH SET
    ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET 
←   −0.0 →
RET
FLOOR1
DOOR
Position setting menu
 ** PRESET NUMBER SET **
  2
  6
 10
 14
 18
 22
 26
 30   1
  5
  9
 13
 17
 21
 25
 29
   ID:DOOR
RET  3
  7
 11
 15
 19
 23
 27
 31  4
  8
 12
 16
 20
 24
 28
 32
PRESET NUMBER SET menu
→PUSH SET→PUSH SET
    ** POSITION 1 **
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET 
←   −0.0 →
RET
FLOOR1
DOOR
Position setting menu
ZOOM/FOCUS setting menu 
						

							19
Preset Identification Setting (PRESET ID)
1.Move the cursor to PRESET ID on the preset setting menu and
select ON or OFF by moving the joystick to the right or left.
The factory default setting is OFF.
ON:Preset ID appears on the monitor screen.
OFF:Preset ID does not appear.
2.Press the CAM (SET) key to display the preset ID setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using the joystick,
and press the CAM (SET) key.
(2) The selected character appears in the editing area. (The
pointer in the editing area moves to the right automati-
cally at this moment.) To enter a blank, select SPACE.
(3) Repeat the above procedure until all characters are
entered.
To Copy a Preset ID from Another Position
(1) Move the cursor to COPY and press the CAM (SET) key. The
preset ID in the preceding position is immediately shown.
Each consecutive pressing of the CAM (SET) key displays the
ID preceding the one currently displayed.
(2) Display the most prospective ID.
(3) Follow the step “To Change an Entered Preset ID” if neces-
sary.
To Change an Entered Preset ID
(1) Move the pointer to the character to be edited in the editing
area by using the joystick.
(2) Select a new character by using the joystick.
(3) Press the CAM (SET) key to determine the Preset ID.
To Delete an Entered Preset ID
Move the cursor to RESET and press the CAM (SET) key.     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu
Command
Editing
Area
Character
Area
PointerCharacter Cursor
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
    
Preset ID setting menu
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
    
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE     
    COPY POSI RET RESET
    DOOR............
    
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
     
						

							20
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM (SET) key. The
display position set menu appears.
(2) Using the joystick, move the ID to the desired position on the
monitor screen, and press the MON (ESC) key. The display
position is set and the monitor screen returns to the preset ID
setting menu.
To Enter the Next ID without Returning to the Preset Setting
Menu
(1) In the preset ID setting menu, move the cursor to the top line
and select the desired position number by moving the joy-
stick to the right or left.
(2) Enter, copy, change or delete the ID as described above.
To Return to the Preset Setting Menu
Move the cursor to RET and press the CAM (SET) key.
Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
moving the joystick to the right or left.
The factory default setting is ALC.
ALC:The lens iris is automatically adjusted to suit the brightness
of the object.
MANUAL:The lens iris is fixed at the set value regardless of the
brightness of the object.
2. In case of ALC 
Press the CAM (SET) key. The backlight compensation menu
appears on the monitor screen. See page 30 for the setting.
3. In case of MANUAL 
Press the CAM (SET) key. The setting menu appears on the moni-
tor screen. Set the lens iris level as desired by moving the joystick
to the right or left.
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
    
     
FLOOR 1
DOOR
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
    
Display position set menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu
   ** MANUAL CONT **
IRIS
RET••••|••••
CLOSE   OPEN
Manual setting menu 
						

							21
Dwell Time (DWELL TIME)
• Move the cursor to DWELL TIME and set a dwell time by moving
the joystick to the right or left. The factory default setting is 10S.
Dwell time changes as follows:
S stands for second(s), and MIN stands for minute(s).
Scene File Setting (SCENE FILE)
1. To set a scene file number
Move the cursor to SCENE FILE and select a scene file number (1
to 10, or OFF) by moving the joystick to the right or left. The facto-
ry default setting is OFF. No scene file is selected at OFF.
2. To set scene file details
Move the cursor to a scene file number and press the CAM (SET)
key. The setting menu appears.
See the pages below for the setting.
Shutter speed: page 32
AGC: page 32
White balance: page 34
Auto focus: page 36
Preset Speed Setting (PRESET SPEED)
• Move the cursor to PRESET SPEED and select a speed by moving
the joystick to the right or left.
To Return to the Preset Number Set Menu
• Move the cursor to RET and press the CAM (SET) key. The PRE-
SET NUMBER SET menu appears with the * mark on the right of
the preset position number.
To Return to the Setup Menu
• Move the cursor to RET and press the CAM (SET) key.
2S3S5S10S30S1MIN2MIN3MIN4MIN
   ** SCENE FILE 1 **
SHUTTER
AGC
WHITE BAL
AF MODE
RETOFF
ON(MID)
ATW 
MANUAL S
Scene file setting menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
1 
••••••••|
L       H
Preset setting menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu
 ** PRESET NUMBER SET **
  2
  6
 10
 14
 18
 22
 26
 30   1*
  5
  9
 13
 17
 21
 25
 29
   ID:DOOR
RET  3
  7
 11
 15
 19
 23
 27
 31  4
  8
 12
 16
 20
 24
 28
 32
PRESET NUMBER SET menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
OFF
••••••••|
L       H
Preset setting menu