Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

32
Shutter Speed Setting (SHUTTER)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP menu on the monitor screen.
2. Move the cursor to SHUTTER and select the electronic shutter
speed by using the joystick. The factory default setting is OFF.
The electronic shutter speed changes as follows by operating the
joystick:
•When OFF is selected for BLC on the ALC CONT menu
Gain Control (AGC)
1. Display SET UP on the monitor...

33
Synchronization (SYNC)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP menu on the monitor screen.
2. Move the cursor to SYNC and select line-lock (LL) or internal (INT)
by using the joystick.
The factory default setting is INT.
Important Notices:
1. The priority of SYNC modes is as follows:
1. Multiplexed vertical drive (VD2) (highest priority)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. To use...

34
7. Use the joystick to match the vertical phases for both video output
signals as closely as possible. (COARSE adjustment can be
incremented in steps of 22.5 degrees (16 steps) with the joystick.)
Note:After the 16 steps, the adjustment returns to the first step.
8. Move the cursor to FINE by using the joystick.
9. Use the joystick to match the vertical phase for both video output
signals as closely as possible.
Notes:
•When the “|” cursor reaches the “+” end, it jumps back to “–”.
At the same time,...

35
(2) Automatic White Balance Control Mode (AWC)
1. Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP menu on the monitor screen.)
2. Move the cursor to WHITE BAL and select AWC →PUSH SW by
using the joystick.
3. Press the CAM (SET) key to start the white balance setup. PUSH
SW is highlighted to indicate that white balance is being set.
4. PUSH SW returns to normal when balance setting is completed.
5. For fine adjustment of the AWC, move...

36
Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the following mode by
moving the joystick to the right or left.
The factory default setting is MANUAL S.
S, M and L stand for Small, Middle and Large areas in the center
of a scene that are used for sensing sharpness in auto-focusing.
MANUAL S, M, L:Brings the camera into focus when the AF key
on the controller is pressed.
AUTO S, M, L:Brings the camera into focus while operating pan,
tilt or zoom manually. These may be selected...

37
Electronic Zoom (EL-ZOOM)
The electronic zoom magnifies a scene 2-fold. With a 18-fold optical
zoom lens, the camera is capable of 36-fold zoom.
1. Move the cursor to EL-ZOOM and select ON or OFF by moving
the joystick to the right or left, and then press the CAM (SET) key.
The factory default setting is ON.
ON:Two (2) - fold electronic zoom is available with the ZOOM
switch on the controller.
OFF:The electronic zoom function is not used.
Notes:
•A scene magnified by the electronic zoom function may...

38
 Special Menu (SPECIAL)
This menu lets you adjust and set up the picture quality to meet your
requirements.
•Display SET UP on the monitor screen.
(Refer to Setup Menu Display on page 16 for details on displaying
the SET UP on the monitor screen.)
•Move the cursor to SPECIAL and press the F2 button of the WV-
CU550B. The special menu appears on the monitor screen.
(For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.)
(1) Chroma Level Setting (CHROMA GAIN)...

39
(5) To Restore the Camera Default Position (REFRESH)
Move the cursor to REFRESH by using the joystick and press the
F2 button of the WV-CU550B.
(For the WV-RM70, WV-CU360 or WV-CU161, keep pressing the
Right and Left switches simultaneously for 2 seconds or more.)
(6) Camera Resetting (CAMERA RESET)
Move the cursor to CAMERA RESET by using the joystick and
press the F3 button of the WV-CU550B.
The camera is reset to the factory preset parameters.
(For the WV-RM70, keep pressing the Right, Left and Set...

40
How to Reset to the Factory Preset Parameters
Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the
factory preset parameters by placing the cursor over the desired mode and then press the F2 button of
the WV-CU550B. (For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 sec-
onds or more.)
RS485 Setup
Initial Camera Communication Parameters
In an RS485 chain the matrix switcher, PC, controllers and cameras should be set to...

41
X ON/X OFF (X ON/X OFF)
Specifies whether to apply flow control or not (NOT USE, USE). The factory setting is NOT USE.
Wait Time (WAIT TIME)
Specifies the time to wait until retrying after confirming that no data is received from the controller.
(OFF: no retry, 100, 200, 400, 1 000 ms).
The factory setting is OFF.
Delay Time (DELAY TIME)
Specifies the time to transmit the acknowledge request when communicating on a 2-line connection.
[----,100 ms] Default: ---- (no set).
This menu appears only when a...