Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

12
Auto Pan Key (AUTO PAN KEY)
This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the con-
troller.
After setting this, the AUTO key performs as assigned.
Note:The AUTO PAN LED on the controller does not light if the mode other than the AUTO PAN mode is
assigned.
Local/Remote (LOCAL/REMOTE)
This setting determines whether the camera continues or stops the ongoing auto operation when the con-
troller is turned off.
LOCAL:The camera continues operating in the auto mode...

13
Cleaning (CLEANING)
This is used for refreshing the electric-mechanical contacts built in the camera. Use this function for
maintenance when the camera has been directed to a specific spot or panned over a specific range
for a long time.
Image Hold (IMAGE HOLD)
The camera picture remains a still image on the monitor screen or until the camera reaches the pre-
set position. This function is useful for surveillance via a local area network.
Camera
(1) Camera Identification (CAMERA ID)
You can use the...

14
Note:The result of field setup of the mask area and level adjustment is fed back (effected) to the lens
iris control in ALC mode.
(3) Shutter Speed (SHUTTER)
You can select a shutter speed of 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and
1/10 000 seconds.
See page 32 for the setting.
(4) Gain Control (AGC)
You can set the gain (brightness level portion of an image) to automatic adjustment [Automatic Gain
Control ON (LOW, MID, HIGH)] or fixed (Automatic Gain Control OFF).
See page 32...

15
(6) White Balance (WHITE BAL)
You can select one of two modes for white balance adjustment as follows:
• Auto-Tracing White Balance (ATW)
In this mode, the color temperature is monitored continuously and thereby white balance is set auto-
matically. The color temperature range for the proper white balance is approx.2 600 - 6 000 K. Proper
white balance may not be obtained under the following conditions:
1. The color temperature is out of the 2 600 - 6 000 K range.
2. When the scene contains mostly...

16
SETTING PROCEDURES
The following setting procedures are described on the assumption that this model is used in combination
with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case of using a controller
other than the WV-CU550B, refer to the table on page 10.
Menu Display
Setup Menu Display
WV-CU550B
1. Select the camera number you want to set up and a monitor to
display the SET UP MENU.
2. Display the D4 menu on the LCD by pressing the appropriate cur-
sor buttons.
3. Press the F1...

17
Presetting
Preset Menu Display
1.Displaying the preset menu directly
(1) Move the cursor to PRESET 1  and move the joystick to the
right or left to select the position number to be set.
(2) Press the CAM (SET) key.
The preset setting menu appears on the monitor screen.
2.Displaying the preset menu from the PRESET NUMBER SET menu
(1) Move the cursor to MAP  and press the CAM (SET) key.
The PRESET NUMBER SET menu appears on the monitor
screen.
(2) Move the cursor to the position number to be set and...

18
3. Pan Offset
If the camera is replaced with a new one, the pan offset function
is used to adjust its positions to be the same as before except
patrol setting.
The controller can be downloaded or uploaded the preset posi-
tion data.
Caution:The preset data for other camera models (WV-CS650 for
example) is incompatible with WV-CS564s.  WV-CS564s pre-
set data will be destroyed if you upload the conventional
data. If this happened, reset the WV-CS564 to the default set-
tings. Download the factory...

19
Preset Identification Setting (PRESET ID)
1.Move the cursor to PRESET ID on the preset setting menu and
select ON or OFF by moving the joystick to the right or left.
The factory default setting is OFF.
ON:Preset ID appears on the monitor screen.
OFF:Preset ID does not appear.
2.Press the CAM (SET) key to display the preset ID setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using the joystick,
and press the CAM (SET) key.
(2) The selected character appears in the...

20
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM (SET) key. The
display position set menu appears.
(2) Using the joystick, move the ID to the desired position on the
monitor screen, and press the MON (ESC) key. The display
position is set and the monitor screen returns to the preset ID
setting menu.
To Enter the Next ID without Returning to the Preset Setting
Menu
(1) In the preset ID setting menu, move the cursor to the top line
and select the desired position...

21
Dwell Time (DWELL TIME)
• Move the cursor to DWELL TIME and set a dwell time by moving
the joystick to the right or left. The factory default setting is 10S.
Dwell time changes as follows:
S stands for second(s), and MIN stands for minute(s).
Scene File Setting (SCENE FILE)
1. To set a scene file number
Move the cursor to SCENE FILE and select a scene file number (1
to 10, or OFF) by moving the joystick to the right or left. The facto-
ry default setting is OFF. No scene file is selected at OFF.
2....