Panasonic Color Cctv Camera Wv Cs564 Operating Instructions

22
Deleting Preset Positions
1. Move the cursor to PRESET 1* and select the position number to
be deleted by using the joystick.
2. Press the CAM (SET) key to display the preset setting menu.
3. Move the cursor to DEL and press the CAM (SET) key.
This deletes the preset position and the PRESET NUMBER SET
menu appears. The * mark on the right of the number disappears.
Note:Your selected preset number is cancelled only in the SEQ
and SORT mode. The previously set parameters (for PAN,
TILT positions, etc.)...

23
Auto Mode Selection (AUTO MODE)
1. To set auto mode
Move the cursor to AUTO MODE and select a mode by moving
the joystick to the right or left.
The factory default setting is OFF.
Modes change as follows:
OFF:No automatic operation. The camera can be operated only
manually.
SEQ:The camera operates in the sequence of preset positions in
numerical order.
SORT:The camera operates in the sequence of preset positions
counterclockwise from Pan Starting Point.
AUTO PAN:The camera automatically turns within...

24
5. To set pan limit ON/OFF
Move the cursor to PAN LIMIT and select ON or OFF by mov-
ing the joystick to the right or left.
The factory default setting is OFF.
ON:Manual pan is limited from the starting point to the end-
point specified by position setting. Set ENDLESS to OFF
before PAN LIMIT is set to ON.
OFF:Manual pan is not limited.
Note:When ON is selected for PAN LIMIT, manual pan moves the
camera away from the other side (PAN LIMIT) of the start-end
range.
6. To set ENDLESS to ON/OFF
Move the...

25
Auto Pan Key Setting
(AUTO PAN KEY)
This is used for assigning one of the following auto functions to the
AUTO key on the controller. Pressing the AUTO key activates the
assigned function after this setting.
•Move the cursor to AUTO PAN KEY and select an auto function by
moving the joystick to the right or left.
The factory default setting is AUTO PAN.
Mode changes as follows:
AUTO PAN:assigns auto panning function to the key.
SEQ:assigns the sequence function to the key.
SORT:assigns the sort...

   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 LOCAL/REMOTE
 PATROL
 CLEANING
CAMERA
RS485 SET UPOFF
OFF
OFF
AUTO PAN
LOCAL
STOP
OFF
Special 1 menu
26
 Patrol Learn and Patrol Play
(PATROL)
A routine of manual operations can be stored for 30 seconds at the
maximum and reproduced repetitively.
1. Set the following parameters for the patrol learn starting position.
These parameters are stored when the patrol learn mode starts.
•PAN/TILT/ZOOM/FOCUS
•IRIS...

27
Patrol Learn with a Controller not Having the PATROL Key
1. Select the patrol learn in the setup menu, and then close it.
Starting points are stored and “LEARNING” appears on the moni-
tor screen.
2. Operate the patrol learn manually.
3. Open the SET UP menu to stop learning.
Notes:
•It is recommended that you set PAN LIMIT to ON for the
patrol learn. Otherwise PAN LIMIT is invalid for playback.
•Start the patrol learn function again from the starting point, If
the power has failed during the patrol...

28
 Cleaning (CLEANING)
Built-in electric mechanical contacts are refreshed at regular
intervals (approx. 7 days) if CLEANING is set to ON.
A dry contract affects adversely picture quality and motors oper-
ation.
1. Move the cursor to CLEANING and select ON or OFF by moving
the joystick to the right or left.
The factory default setting is OFF.
ON:The contacts are cleaned as programmed for about 1
minute. “CLEANING” disappears when it is over.
OFF:No contact cleaning.
Note:Select OFF when the camera...

29
3. After editing the camera identification characters, follow the steps
below to set the position of the CAMERA ID on the monitor screen.
3-1 Move the cursor to POSI, and press the CAM (SET) key to display
the ID position menu.
3-2 Use the joystick to decide the position of the CAMERA ID on the
monitor screen. Press the MON (ESC) key to fix the position, and
return to the character editing menu.
Notes:
•When you want the pointer to move to a specific character in the
editing area, select a new...

30
Light Control Setting (ALC/MANUAL)
1. Display SET UP on the monitor screen.
If necessary, refer to Setup Menu Display on page 16 for details
on displaying the SET UP on the monitor screen.
2. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
using the joystick.
The factory default setting is ALC.
When you select ALC, set backlight compensation.
Note:The backlight compensation submenu associated with this
menu is described separately and should be set up after
installing the camera at the site...

31
(2) ALC Mode with BLC OFF
1. Move the cursor to the BLC and select OFF. (When you select
MANUAL, BLC is not available.) The MASK SET appears on the
menu.
2. Move the cursor to MASK SET and press the CAM (SET) key. The
48 mask areas appear on the monitor screen. The cursor is blink-
ing in the top left corner of the screen.
3. To mask an area where backlight is bright, move the cursor to that
area and press the CAM (SET) key. The mask turns to white.
Repeat this procedure to mask the desired area.
4....