Panasonic Center Module Wx C3010 Operating Instructions

11
@7Greeter Start Delay Indicator (Yellow) 
(START DELAY)
This indicates that the greeter start delay has selected
on.
@8 Greeter Start Delay Button (START DELAY)
This button turns the greeter start delay normal and
delay.
@9 Greeter Record Indicator (Red) (REC)
This indicates that while recording in the selected
greeter memory (1 or 2).
#\f Greeter Record Button (REC)
When this button is pushed, the message from Order
Taker or All-in-One Headset is recorded in the selected
greeter memory (1 or 2).
#1...

12
Operating Procedures
Basic Operation
 Power ON 
Press the Power ON/OFF Switch of the center module to turn
the power supply ON. 
It takes about 5 seconds until the power supply is started. 
Then, press the Power buttons of the Order Taker and the
All-in-One Headset to turn their power supplies ON. 
Communications with Customers (TALK)
Store personnel wearing the headset can communicate bidi-
rectionally with any customer who is at the menu board.
In regard to the method of talking, refer to the...

13
5. Press the SPEED TEAM button of the Center Moduleagain, the SPEED TEAM mode will be released. The
Order Taker or All-in-One Headset allows the operator to
hear the voice prompt of the SPEED TEAM OFF.
Notes:• TALK is prohibited in the speed team mode.  If TALK is attempted with the Order Taker or the All-
in-One Headset, a voice prompt of Operation not
allowed is heard from the headset speaker. 
• If POS Remote is set for ON, you have to note that no button operation of the speed team is possible at...

14
Note:• If POS Remote is set for ON, you have to note that no button operation of the Beep Day/Night is possible at the
center module.
DAY mode: When you are taking charge of lane A, if the
vehicle detector is on the lane A, you will hear the beep
A. If the vehicle detector is on of the lane B, you will not
hear the beep B.
NIGHT mode: When you are taking charge of lane A, if the
vehicle detector is on the lane A, you will hear the beep
A. If the vehicle detector is on of the lane B, you will hear
the...

15
 Vehicle Detector Normal/Override On
The Vehicle Detector operation can be set up. 
Normal/Override On setup can be made by button operation
at the front panel of this unit. 
When the Override On mode is set, the V/D Override indica-
tor of the center module will light in yellow. When the V/D
Override button is pressed, the Normal mode is assumed
and this indicator will disappear. 
NORMAL: The vehicle detector turns on only when a vehicle
is detected at the menu board. When the detector turns
on, a...

16
Panasonic WX-C3010 Series System Parts and Accessories
Note:Illustrations may differ from actual products.
 Center Module
WX-C3010 
All-in-One Headset
WX-H3050 
Order Taker
WX-T3020
 Headset
WX-H3027 
Battery
WX-B3030 (1UF653450R-MDSP)
• Only used for WX-H3050 and WX-
T3020
• WX-B3030 and 1UF653450R- MDSP are same models.  
Battery Charger
WX-Z3040
INSTA LL S YSTE M  S ET
TIN G
O PERA TIONAL S ET TIN G I
D R EG IS T
R ATIO N
G RE ETE
R
POW ER
TE LEPHO NE
CO NTR OL  O UT
START
DELA Y
O
N
DOWN
P...

17
Major Operating Controls and Their Functions
qAC Inlet
w Power On/Off Switch
e Through-hole
r Antenna
t Mounting Hole
y Terminal Board Cover
[INSTALLED SYSTEM SETTING]
The following buttons should be used by qualified service
personnel or system installers only.
\b PREV/NEXT Button (INSTALL SYSTEM SETTING,
PREV/NEXT)
These buttons select the system setting items.
i Select Button (SEL)
This button selects set value of the system setting items.
o Auxiliary Input On/Off Indicator (Green) (AUX IN)
This...

18
!6Lane select Indicator (Red/Green) (LANE SELECT)
Select the lane A or B at the double drive-thru.
Red: Selected Lane A
Green: Selected Lane B
!7 POS Remote Control Indicator (Green) 
(POS REMOTE)
This item selects the POS remote control On and Off.
OFF: POS Remote OFF
ON: POS Remote ON
!8 TX Power Indicator (Green) (TX POWER)
This item selects the transmit power Normal and
Attenuation.
OFF: Reduce Power (25 %)
ON: Normal Power
[ID REGISTRATION]
!9ID Registration Indicator (Red) (ID REGISTRATION)
This...

19
Installations/Connections
Installation procedures 
Preparations(Refer to page 19.)
Installation of center modules on the wall(Refer to page 19.)
Wiring to the center modules(Refer to page 20.)
ID registration for follower units(Refer to page 25.)
[System Setup]
Installed System Setting
(Refer to page 26.)
Adjustments to adequate sound levels
Preparations
This Center Module is designed to be mounted on a wall directly. Please \
be advised of the following: 
• Procure 4 mounting screws according to...

20
Wiring to the center modules
1. Remove the terminal cover. 
Slide the front cover downwards by pressing its arrow-
marked part and pull the lower side of the cover toward
you. 
2. Insert a “minus” screwdriver in the slot as illustrated and remove the terminal socket from the main unit. 
3. Connect the wiring material to the terminal socket.  Use the “minus” screwdriver and loosen the screw locat-
ed on the upper surface of the terminal socket. 
Peel off the sheath from the tip of the wiring material...