Panasonic Center Module Wx C3010 Operating Instructions

21
3. Insert the power plug into the power cord inlet.
4. Push the holderforward until the holder touches the
power plug.
5. Lock the holder.
6. Clamp the AC cable with the provided clamp, and secure the AC cable clamper to the wall by fastening the
screws.
AUX SP + (8Ω)
CONNECTOR 1
ORDER INTERFACE
1
AUX SP GND
2OUTSIDE SP + (8 Ω)
3OUTSIDE SP GND
4OUTSIDE MIC +
5OUTSIDE MIC  –
6OUTSIDE MIC GND
7V/DET 1 IN
8COM
9V/DET 2 IN
10SPEED TEAM
CONNECTOR 3
POS INTERFACE
1
TALK LOCK RELEASE
2MANAGER SELECT
3PAGE...

22
MENUBOARDAUX
SPEAKER
VEHICLE
DETECTOR
EXTENSION VEHICLE
DETECTOR EXTERNAL
DEVICEGooseneck
Microphone
SHIELD
SHIELD GND
5
*1
AUX SP + (8Ω)
CONNECTOR 1
ORDER INTERFACE
1
AUX SP GND
2OUTSIDE SP + (8Ω)
3OUTSIDE SP GND
4OUTSIDE MIC +
5OUTSIDE MIC –
6OUTSIDE MIC GND
7V/DET 1 IN
8COM9V/DET 2 IN
10AUX MIC +
CONNECTOR 2
ORDER INTERFACE
1
AUX MIC –
2AUX MIC GND
3AUX MIC PTT
4COM5DEVICE CONTROL
6COM7N.C8
Microphone
Speaker
 Basic Connection
This diagram shows the basic system connection.
*1 OUTPUT: Photocoupler...

23
*1 *1 *1 *1*2 *2 *2 *2 *1 *1GND
+12V
I/O
I/F
POS System
SPEED TEAM
CONNECTOR 3
POS INTERFACE
1
TALK LOCK RELEASE
2MANAGER SELECT
3PAGE SELECT
4IN COM
5POS AUDIO IN
6POS AUDIO GND
7POS AUDIO OUT
8POS AUDIO GND
9V/DET 1
CONNECTOR 4
POS INTERFACE
1
V/DET 2
2TALK3PAGE4OUT COM
5NIGHT MODE
6OUTSIDE SP LEVEL
7
*1 INPUT: Non-voltage make contact
*2 OUTPUT: Photocoupler (PS2501L)-isolated, max. 10 mA
 POS (Point of sales)-System Connection
This diagram shows the connection with the POS system. 

24
Lane A
Lane B
GNDLAN Cable with Shield
CONNECTOR 51
2
3
4
5
COM N.C
6
CONNECTOR 51
2
3
4
5
COM
N.C
6
DOUBLE-DRIVE-THRU
Use a LAN cable
with the shield type
CONNECTOR 7
DDT INTERFACE
DOUBLE-DRIVE-THRU
Use a LAN cable
with the shield type
CONNECTOR 7
DDT INTERFACE
 Double-Drive-Thru Connection
This diagram shows the connection in the double-drive- thrusystem. 

25
ID registration for follower units
• To talk with the headsets (Order Taker and All-in-One Headset), ID reg\
istration is required. 
• For ID registration, set the center module in ID registration mode and m\
ake operation of ID registration by means of a follow-
er unit. 
ID registration procedures are described below based on the All-in-One H\
eadset. 
1. Turn on the power of the Center Module. 
2. Press the ID Registration Button of the center module for 2 seconds or more. The system is changed to...

26
Installed System Setting
After the completion of installation work, system setup shall be made ac\
cording to the equipment to be connected and the oper-
ation mode. 
Setup operation for the installed system shall be carried out by the use\
 of the PREV/NEXT button and the  SELbutton. 
1. Turn on the power supply of the center module. 
2. Press the [NEXT] button or the [PREV] button.  Indicator of the selected setup item blinks. Each time the
[SEL] button is pressed, there is a reciprocal
changeover...

27
IndicatorEcho Canceller
Level Sound Quality Remarks
OFF
OFF
Green
Yellow Red –
No Echo Canceller processing
LOW High When the effect of echo is small, this position is selected.
MID
HIGH Normal
Low When the effect of echo is large, this position is selected. This setting is default. (*1)
Setup operation for Echo Canceller (Echo Canceller Effect Level Control\
)
The effect of Echo Canceller (the amount of echo erase) is set up. 
Setup operation for DNR Level (Digital Noise Reduction Effect Level Con\...

28
ON: DUAL LANE ON (Green)When there is car in only Lane B, the greeter memory 1
output to the speaker of Lane B.
OFF: DUAL LANE OFF When there is car in only Lane B, the greeter message
of the memory (1 or 2) is output to the speaker of
Lane B. When there are cars in Lane A and B, the greeter memo-
ry 2 is output to the speaker of Lane B.
LANE A
WINDOW #1
WINDOW #2 LANE B
DRIVE-THRU LANE
LANE A
WINDOW #1
WINDOW #2 LANE B
DRIVE-THRU LANE
Pull forward
(Memory 1)Hello
(Memory 2)Hello
(Memory 1 or 2)
LANE...

29
Lane setup
In the case of Double-Drive-Thru, one each unit of Center Module is set \
for Lane A and Lane B, respectively. 
Only for the Center Module of Lane B, the Dual Lane is set at ON.
When Lane A or Lane B setup is changed over, the center module will be r\
estarted automatically. 
If the [TALK] and [PAGE] indicators begin to blink after restarting, che\
ck the connections between both center modules. 
Red: Lane A (Generally, this setting is used. This setting is default.)
Green: Lane B
Note: If...

POS AUDIOSTATE OUTPUT
DAY
OUTSIDE SP LEVEL INPUT Outside speaker volume is normal level.
(To short-circuit the terminals)
Outside speaker volume is 50 % level.
(To open-circuit the terminals)
DAY
Disables the vehicle detector beep on the other
lane. (To short-circuit the terminals)
NIGHT MODE INPUT
30
PAGE
Activated when a PAGE sound is provided to POS
AUDIO OUT.
TALK
NIGHT
NIGHT Reduces the volume of the vehicle detector beep
on the other lane. (To open-circuit the terminals) Activated when a TALK sound...