Panasonic Cctv Cameras Wv Bp330 Operating Instructions

							(Lens : option)
Before attempting to connect or operate this product,
please read these instructions completely.
CCTV Cameras
WV-BP330/WV-BP332/WV-BP334
FRANÇAIS
ENGLISH 
						

							WARNING:TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The serial number of this product may be found on the top
of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
Warning:This equipment generates and uses radio frequency energy
and if not installed and used properly, i.e., in strict accor-
dance with the instruction manual, may cause harmful
interference to radio communications.  It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection
against such interference when operated in a commercial
environment.
For U.S.ACAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the products enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilater-
al triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompa-nying the appli-
ance.
SA 1965
SA 1966 
						

							CONTENTS
PREFACE ........................................................................................................................................................................ 2
FEATURES ...................................................................................................................................................................... 2
PRECAUTIONS ............................................................................................................................................................... 3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS  ......................................................................................... 4
CONNECTIONS .............................................................................................................................................................. 8
FOCUS OR FLANGE-BACK ADJUSTMENT .................................................................................................................. 13
INSTALLATION OF CAMERA ........................................................................................................................................ 14
PREVENTION OF BLOOMING AND SMEAR  ................................................................................................................ 15
SPECIFICATIONS .......................................................................................................................................................... 16
STANDARD ACCESSORIES  ......................................................................................................................................... 17
-1-
ENGLISH 
						

							-2-
1. The following functions are built-in.
(1) Auto Light Control (ALC)/Electronic Light
Control (ELC)
(2) Back Light Compensation (ON: Photometric
weight is given to the center of the
screen/OFF: Effective if the object is not in the
center of the screen)
(3) Various External Sync Functions, including
Gen-Lock
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.08 lux (0.008 foot-can-
dle) with F1.4 lenses
4. Horizontal resolution of 570 lines
5. Shooting of shoot indoor scenes with fixed iris lens
by use of Electronic Light Control (ELC) function
ture elements), and digital signal processing LSI’s. This
model offers cutting-edge technology for advanced
video surveillance.
PREFACE
Panasonic’s WV-BP330 series digital cameras intro-
duce a new level of high picture quality and high reso-
lution through the use of a 1/3-inch interline transfer
CCD image sensor having 768 horizontal pixels (pic-
FEATURES
6. Selectable auto iris control signal for the lens from
a video signal or DC control signal 
						

							-3-
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws
or covers.
There are no user serviceable parts inside. Ask a
qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera.  Avoid striking, shaking,
etc.  The camera could be damaged by improper
handling or storage.
3. Do not expose the camera to rain or moisture,
or try to operate it in wet areas.
Turn the power off immediately and ask a qualified
service person for servicing. Moisture can damage
the camera and also create the danger of electric
shock.
4. Do not use strong or abrasive detergents when
cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether
the camera is in use or not, never aim it at the sun
or other extremely bright objects. Otherwise,
blooming or smear may be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where tempera-
ture is between –10°C - +50°C (14°F - 122°F), and
humidity is below 90%.  The input power source is
120V AC 60Hz for WV-BP330, 12V DC for WV-
BP332, and 24V AC 60Hz for WV-BP334.
Caution:
To prevent fire or electric shock hazard, a UL
listed wire (VW-1, style 1007) should be used for
DC 12V or AC 24V Input Terminals.
PRECAUTIONS 
						

							-4-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
WV-BP330BP330
VIDEO OUTGEN-LOCK
L
INT
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVELV. PHASEH
Ω
LL
OFF
ELC
OFF
DC
Hi-Z
GND AC  24V  IN
12
VIDEO OUTGEN-LOCK
L
INT
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVELV. PHASEH
Ω
LL
OFF
ELC
OFF
DC
Hi-Z
DC 12V  IN
VIDEO OUTGEN-LOCK
L
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVELH
Ω
OFF
 ELC
OFF
DC
Hi-Z


 
						

							-5-
qAuto Iris lens ConnectorThis connector is for connecting the auto iris lens
by a 4-pin male connector supplied as a standard
accessory (Part No. YFE4191J100).
wFlange-back Adjusting RingThis ring adjusts the back focal length or picture
focus. Rotate this ring clockwise for a C-mount
lens or counterclockwise for a CS-mount lens.
eLens (option)
rCamera Mounting Screw HoleThis hole for mounting the camera onto a mounting
bracket.
tPower Cord (only WV-BP330)Connect this power cord to an electrical outlet of
120V AC 60Hz.
yDC 12 V Input Terminal 
(DC 12V IN (only WV-BP332))
This terminal is for connecting the 12V DC power
supply cord.
uAC 24V  Input Terminal 
(AC 24V IN (only WV-BP334))
This terminal is for connecting the 24V AC 60Hz
power supply cord.
iSynchronization Mode Selector 
(INT,  LL (only WV-BP330 and WV-BP334))
Selects the camera synchronization mode from
internal sync mode (INT) or line-lock mode (LL).
INT:When no signal is supplied to the GEN-LOCK
connector, the camera synchronization mode
is set to internal 2:1 interlace. Whenever the
gen-lock video signal is supplied to the GEN-
LOCK connector, the camera synchronization
mode is automatically set to external synchro-
nization.
LL:The camera synchronization mode is set to
line-lock even if the gen-lock video signal is
supplied to the GEN-LOCK connector.
Note:Set this selector to INT for gen-lock opera-
tion.
oAGC ON/OFF Selector (AGC ON, OFF)Selects the gain of the video amplifier as follows:AGC ON:When the lens iris is fully open under
low light conditions, a clear picture is
obtained by automatic increase of the gain.
OFF:A natural and low-noise picture is obtained
under low light conditions. 
						

							-6-
!0Automatic Light Control / Electronic Light
Control Selector (ALC , ELC)
Lets you select the mode according to the lens
type that is used with this camera.
ALC:Select this mode when an auto iris lens (ALC
lens) is used with this camera.
ELC:Select this mode when a fixed iris lens or
manual iris lens is used with this camera.
!1Back Light Compensation Mode Selector (BLC
ON, OFF)
Lets you select the mode according to the position
of the object and light conditions on the screen.
BLC ON:More photometric weight is given to the
center of the screen than to the edge of the
screen. Select this mode if the background
light is strong such as a spotlight. 
OFF:Select this mode if the main object is not
located in the center of the screen and a
source of bright light is located near the cen-
ter of the screen.
!2Lens Drive Signal Selector (VIDEO, DC)
Lets you select the mode according to the type of
auto iris lens drive signal to be supplied to the lens
from the auto iris lens connector.
VIDEO:Select this mode if you are using the auto
iris lens that requires a video drive signal.
DC:Select this mode if you are using the auto iris
lens that requires a DC drive signal.
!3Gen-lock Termination Selector  (Hi-Z, G/L75Ω)
Set this selector to Hi-Z when a gen-lock video
input signal is looped through. In all other cases,
set this selector to 75
Ω.
!4Vertical Phase Control 
(V. PHASE (only WV-BP330 and WV-BP334))
Allows you to adjust the vertical phase of the cam-
era signal to match the vertical phase of the line
powers.
!5Video Level Control (VIDEO LEVEL, H(High)-
L(Low))  
Allows you to adjust the video level when the Lens
Drive Signal Selector is set to DC and the auto iris
lens requiring the DC drive signal is mounted on
the camera.
Note:The video level should be adjusted by the
lens when the auto iris lens requiring the video
drive signal is mounted on the camera.
!6Video Output Connector  (VIDEO OUT)  
This connector is for connecting with the VIDEO IN
connector of the monitor. 
						

							-7-
Cautions:
1. Connect to 12V DC (10.5V-16V) or 24V AC
(19.5V-28V) class 2 power supply only.
Make sure to connect the grounding lead
to the GND terminal when the power is
supplied from a 24V AC power source.
2. To prevent fire or electric shock hazard,
use a UL listed wire VW-1, style 1007 cable
for the Input Terminal.
!7Gen-lock Input Connector (GEN-LOCK) 
This connector is for connecting an external sys-
tem for synchronization. 
						

							-8-
CONNECTIONS
A. WV-BP330 (120V AC 60Hz)
Connect the power cord to an electrical outlet of
120V AC 60Hz.
B. WV-BP332 (12V DC)
Connect the power cord to the DC 12V IN terminal
on the rear panel of the WV-BP332.
12 V DC
(10.5 V - 16 V)
Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
Resistance 0.078 0.050 0.030 0.018
Ω/m
Resistance 0.026 0.017 0.010 0.006
Ω/ft
Resistance of copper wire [at 20°C (68°F)]
•Calculation of maximum cable length between
camera and power supply :
10.5V DC ≤VA−(R x 0.42 x L) ≤16V DC
L  : Cable length (meters)
R  : Resistance of copper wire (
Ω/meters)
V
A: DC output voltage of power supply unit
V
A−12
L standard =   (meters)
0.42 x R
V
A−16
L minimum =   (meters)
0.42 x R
V
A−10.5
L maximum =   (meters)
0.42 x R
@!