Panasonic Cctv Cameras Wv Bp330 Operating Instructions

-9-
C. The maximum extensible coaxial cable
length between the camera and the monitor is
shown below.
Video Cable
1. It is recommended to use a monitor whose resolu-
tion is at least equal to that of the camera.
2. Set the termination switch to the 75
Ωposition on
the last monitor.
A. Use a 75
Ωcoaxial cable.
B. Set the termination switch to the 75
Ωposi-
tion on the last monitor and to the Hi-Z posi-
tion on the other monitors. Do not change the
positions after setting.
OUT IN 75Ω
Hi-Z
VIDEOOUT IN 75Ω...

3. Wiring precautions:
•Do not bend the coaxial cable into a curve whose
radius is smaller than 10 times the cable’s diame-
ter.
•Never staple the cable, not even with circular sta-
ples. Impedance mismatching will occur.
•Never crush or pinch the cable.
All of the above will change the impedance of the
cable and cause poor picture quality.
-10-
Type of RG-59/U RG-6/U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800
maximum
cable length (ft) 825 1 650 1 980 2...

-11-
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a
video drive ALC lens.
The installation should be made by qualified ser-
vice personnel or system installers.
(1) Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover as shown
in the diagram below.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9V DC, 50mA max.
Pin 2: Not used
Pin 3: Video...

-12-
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount (1”-
32UN) and the lens weight should be less than 450
g
(0.99 lbs). If the lens is heavier, both the lens and cam-
era should be secured by using the supporter.
The protrusion at the rear of the lens should be as
shown below:
C-mount: Less than 11.5 mm (7/16”)
CS-mount: Less than 7.2 mm (1/4”)1
2
Screws
Flange-back
Adjusting Ring
Mounting the Lens
Caution:
Before you mount the lens, loosen the two screws
on the ring, and...

-13-
The following adjustment should be made by qualified
service personnel or system installers.
1. Loosen the screws on the flange-back adjusting
ring.
2. Turn the flange-back adjusting ring to the desired
position.
Caution:When the C-mount lens is mounted, do
not rotate the ring counterclockwise by force
after it stops. If the ring is rotated by force, the
inner lens or CCD image sensor may be dam-
aged.
3. Tighten the screws on the flange-back adjusting
ring.
Note:If the camera is connected to the...

-14-
• Mounting from the bottom
This camera is designed to be mounted from the
bottom, as shown below. The mounting hole is a
standard photographic pan-head screw size (1/4”
- 20).
•Mounting from the top
Remove the mount adapter from the bottom of the
camera by removing the two fixing screws.  Attach
the mount adapter to the top as shown in the dia-
gram, then mount the camera on the mounting
bracket.
Make sure that the two original fixing screws are
used when mounting the mount adapter as longer
length...

-15-
When the camera is aimed at a bright light, such as a
spot light, or a surface that reflects bright light, smear
or blooming may appear.  Therefore, the camera
should be operated carefully in the vicinity of extremely
bright objects to avoid smear or blooming.
 




Bright object
Smear
PREVENTION OF BLOOMING AND SMEAR 

Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCD
Scanning Area: 4.9 (H) x 3.7 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)
Synchronization: Internal, External, Line-locked or Multiplexed vertical drive (VD2) selectable 
Scanning System: 2 : 1 interlace
Scanning: 525 lines / 60 fields / 30 frames
Horizontal: 15.734 kHz
Vertical: 59.94 Hz
Horizontal Resolution: 570 lines
Video Output: 1.0 V[p-p] EIA composite 75 
Ω/ BNC connector
Signal-to-Noise Ratio: 50 dB (AGC OFF)...

Dimensions (without lens): 67 (W) x 55 (H) x 123 (D) mm
[2-5/8” (W) x 2-3/16” (H) x 4-13/16” (D)]
Weights (without lens): WV-BP330: 0.62
kg(1.40lbs)
WV-BP332: 0.445
kg(0.98lbs)
WV-BP334: 0.470
kg(1.04lbs)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
-17-
STANDARD ACCESSORIES
Body Cap .....................................................................................1 pc.
ALC Lens Connector (YFE4191J100)...

VERSION FRANÇAISE(FRENCH VERSION)
MISE EN GARDE:AFIN DE PRÉVENIR TOUT RISQUE DINCENDIE OU DE CHOCS ÉLECTRIQUES, ÉVITER 
DEXPOSER CET APPAREIL À LA PLUIE OU À UNE HUMIDITÉ EXCESSIVE.
Le symbole de léclair dans un triangle
équilatéral indique la présence dune ten-
sion suffisamment élevée pour engendrer
un risque de chocs électriques.
Linterférence radioélectrique générée par cet appareil
numérique de type A ne dépasse pas les limites
radioélectriques, section appareil numérique, du Ministère
des...