Panasonic Aj Spc700p Operating Instructions Manual

71
5
Chapter 5 Preparation (continued)
Reading out the Lens File Data 
1Select the lens file No. to read out by following Steps 1
to 3 in the [Storing the Lens File Data] section.
2Turn the JOG Dial button to move the cursor to
[READ:]. 
3Press the JOG Dial button and the following message
appears. 
4Turn the JOG Dial button to move the cursor to [YES].
Then, press the JOG Dial button. 
[READ OK] will be displayed after the stored lens file
data has been read out. 
5Press the MENU button to exit the...

72
Chapter 5 Preparation (continued)
5-4 Preparing for Audio Input 
Take the following steps to prepare the camera for
connecting audio input devices. 
5-4-1 When Using the Front Microphone 
The AJ-MC700P microphone kit (optional) includes a
microphone that can be mounted on the camera. 
1Open the microphone holder. 
2Mount the microphone and tighten the clamping screw. 
3Connect the microphone cable to the MIC IN jack on
the camera. 
4Set the AUDIO IN switch to [FRONT] depending on the
audio channel to...

73
5
Chapter 5 Preparation (continued)
5-4-3 When Using Audio Devices 
1Connect the audio device to the AUDIO IN jack with the
XLR cable. 
2Set the AUDIO IN switch to [REAR] for the channel to
which the XLR cable is connected. 
3Set the LINE/MIC/+48V selector switch on the rear
panel to [LINE]. 
5-5 Connection between the USB  2.0 port of the AJ-SPC700P and 
a PC
By connecting the AJ-SPC700P with an external PC using
USB 2.0, the P2 card connected to the AJ-SPC700P can be
used as a mass storage device....

74
Chapter 5 Preparation (continued)

zA USB driver must be installed on the PC.
z AJ-SPC700P is only applicable to USB 2.0, not to
USB 1.1.
z Only one AJ-SPC700P at a time must be connected
to the PC via USB.
z The P2 card must not be removed when it is
connected via USB.
z While a USB connection is established, the P2 card’s
access LED should not be lit except when access is
being carried out.
z While the USB is turned ON, operations such as
recording, playback and thumbnails will not be
available....

75
5
Chapter 5 Preparation (continued)
5-7 Attaching the Shoulder Strap 
To detach the shoulder strap, first open the hooks, then
detach the strap. 

Make sure that the shoulder strap is securely attached. 
5-8 Attaching the Rain Cover 
When using the SHAN-RC700 Rain Cover 
5-9 Connecting the AJ-EC3P Extension Controller 
Some functions can be remote-controlled when the AJ-
EC3P extension control unit (optional) is connected to the
camera. 
When the AJ-EC3P is connected, the camera automatically
enters...

76
Chapter 5 Preparation (continued)
5-10 Attaching the Front Audio Level Control Knob
If you use the Front Audio Level control frequently, attach the
accessory knob so that it can be easily operated. 
Remove the screw in the center of the Front Audio Level
control, and attach the accessory knob using the screw
(included). When attaching the knob, be sure to align the
marks on the control with the marks on the knob. 
Screw Î
Front Audio 
Level Control 
Marks
Knob 
(Accessory) 
Screw 
(Accessory)...

77
6
Chapter 6  Manipulating Clips with Thumbnails 
A clip is a data group that includes the images and voices created from one shooting session, together with additional 
information such as voice memos and meta data. 
The following manipulations can be performed using the cursor and SET buttons, while checking the images displayed on the 
LCD monitor: 
zPlayback, delete, copy or restore the clip.
z Add a voice memo to the clip.
z Add or delete a shot mark on the clip thumbnail.
z Format P2 cards and...

78
Chapter 6 Manuipulating Clips with Thumbnails (continued)
6-2 Thumbnail Screen 
Press the THUMBNAIL button to display the thumbnail
screen on the LCD monitor. Pressing the THUMBNAIL
button again returns the display to the regular display. When
switching is done from the regular screen display to the
thumbnail screen display, all the clips will be displayed on
the thumbnail screen.
Also, pressing the MENU BAR button in the thumbnail
screen moves the pointer to the menu bar and enables
thumbnail menu...

79
6
Chapter 6 Manuipulating Clips with Thumbnails (continued)
 Indicator for clips with proxy
This marker is displayed for clips with proxy attached.
 Indicator for edit copy clips
This marker is displayed for clips whose edit copy
operation was performed on the P2 deck. For more
information on edit copy, see the AJ-SPD850 instruction
manual.
6-3 Selecting Thumbnails 
Multiple thumbnails can be randomly selected in the
thumbnail screen. 
1Use the cursor buttons to move the pointer (yellow
frame) to the...

80
Chapter 6 Manuipulating Clips with Thumbnails (continued)
6-5Switching the Thumbnail Display
The display can be switched so that only those clips
matching the specified conditions are displayed in the
thumbnail screen. 
1Press the THUMBNAIL button. 
The thumbnail screen appears on the LCD monitor. 
2Press the MENU BAR button. The pointer moves to the
menu bar. 
3Move the pointer over THUMBNAIL and press the SET
button to select it. A sub-menu appears. Switch the
thumbnail display by selecting one of...