Panasonic Aj Spc700p Operating Instructions Manual

91
7
Chapter 7  Maintenance and Inspections
7-1 Inspections Before Shooting
Make sure you check that the system is operating normally
before embarking on a shoot. We recommend using a color
video monitor to check the image. 
7-1-1 Preparing for Inspections 
1Mount a charged battery pack. 
2Turn the power switch ON and check that 5 or more
BATT indication marks appear. 
zIf fewer than 5 BATT indication marks appear, replace
the battery with a fully-charged battery. 
3Insert a P2 card into the card slot...

92
Chapter 7 Maintenance and Inspections (continued)
7-1-3 Inspecting the Memory Recording  Functions
Make sure you successively carry out the inspections from
[1. Inspecting the P2 Card Recording] to [4. Inspecting the
Earphone and Speaker]. 
1. Inspecting the P2 Card Recording 
1Check on the display inside the viewfinder that the
remaining P2 card recording capacity is sufficient.
Please refer to [P2 Card Remaining Free Space/
capacity Indication] (page 50) for information about P2
card remaining...

93
7
Chapter 7 Maintenance and Inspections (continued)
6. Inspection of the clock, time code, and user bits
1Set the user’s bit as required. 
Please refer to [4-5-1 Setting the User Bits] for the
setting procedures. 
2Set the time code. 
Please refer to [4-5-3 Setting the Time Code] for the
setting procedures. 
3Set the TCG switch to [R-RUN]. 
4Press the REC START/STOP button. 
Check that the counter display number changes as
recording progresses. 
5Press the REC START/STOP button again. 
Check that...

94
Chapter 7 Maintenance and Inspections (continued)
7-2-4 Connector Signals
Panasonic Part No. K1AA104H0038
Manufacturer Part No. HA16RX-4P(SW1) (Hirose Electric Co.)

Confirm correct polarity when using an
external power supply. 
Panasonic Part No. K1AB103B0013
Manufacturer Part No. NC3FBH2(Eye-Trek)
DC IN
1GND
2NC
3NC
4+12V
FRONT MIC IN
1GND
2 AUDIO IN (H)
3 AUDIO IN (C)
1234
PUSH
1
3
2
Panasonic Part No. K1AB103A0007
Manufacturer Part No. HA16PRM-3SG
(Hirose Electric Co.)
Panasonic Part No....

95
7
Chapter 7 Maintenance and Inspections (continued)
7-3 Warning System
7-3-1 Warning Description Tables
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING 
lamp, lamps inside the viewfinder and a warning tone. 

The WARNING lamp has the highest priority, followed by the tally lamp, and then the warning tone. When multiple errors occur 
simultaneously a higher priority indication will be triggered. The [WIRELESS RF], however,...

96
Chapter 7 Maintenance and Inspections (continued)
5. P2 Card Fully Recorded
Display window 
indication All 7 bar indicators for remaining MEDIA
capacity start blinking. 
WARNING lamp  Continues to light up until an operation is
performed. 
Ta l l y  l a m p Continues to blink 4 times per second until
an operation is performed. 
Viewfinder The END indicator blinks. 
Warning tone Continues to beep until an operation is
performed. 
Warning 
description  The P2 cards are recorded to maximum
capacity....

97
7
Chapter 7 Maintenance and Inspections (continued)
7-3-2 Error Codes
The following error codes are displayed in the display
window if an error occurs in the camera: 
9. Battery Nearly Empty
Display window 
indication  One of the bars in the battery remaining
indicator star ts blinking. 
WARNING lamp  Blinks once per second. 
Ta l l y  l a m p Blinks once per second. 
Viewfinder The BATT LED blinks. 
Warning tone Beeps 4 times per second. 
Warning 
description  The battery is about to run out....

98
Chapter 8  Menu Description Tables
8-1 Menu Configuration
About Menu Description Tables 
USER MENUUSER MENU SELECT
SYSTEM SETTING
PAINT
CAM OPERATION
SYSTEM MODE
  OPTION MODE
  REC FUNCTION  OUTPUT SEL
  GENLOCK
  ROP
  LOW SETTING
  MID SETTING
  CAMERA ID
SHUTTER SPEED
SHUTTER SELECT  USER SWSW MODE  WHITE BALANCE MODE
  IRIS
  FLARE
  USER SW GAIN  MATRIX
  COLOR CORRECTION
SYSTEM SETTING(USER)  PAINT(USER)
  VF(USER)
  CAM OPE(USER)
  FILE(USER)
  MAINTENANCE(USER)
  MAIN OPE(USER) SKIN TONE...

99
8
Chapter 8 Menu Description Tables (continued)
8-2 SYSTEM SETTING
8-2-1 SYSTEM MODE8-2-2 OPTION MODE

Menu options for setting 1394 are displayed when an
IEEE1394 interface board (AJ-YAD800G, optional) is
attached. For more information, see the AJ-YAD800G
instruction manual. Note that the AJ-SPC700P incorporates
the following additional items:
The ____ in the Adjustable Range column indicates the
preset mode. 
Items/
Data Saved  Adjustable 
Range  Remarks 
REC SIGNAL CAMVIDEO
1394Select video input...

100
Chapter 8 Menu Description Tables (continued)
8-2-3 REC FUNCTION 8-2-4 OUTPUT SEL
The ____ in the Adjustable Range column indicates the
preset mode. 
Items/
Data Saved  Adjustable 
Range  Remarks 
PRE REC 
MODEON
OFFSelect whether or not to enable PRE 
RECORDING.
ON:
  PRE RECORDING enabled.
OFF:   PRE RECORDING disabled.

Specify the PRE RECORDING time by 
using the menu option PRE REC TIME.
–CUF –
PRE REC TIME 1SEC : 8SEC : 15SEC
Set PRE RECORDING. 
1-15SEC:
Set the length of time that can be...