Panasonic Aj Spc700p Operating Instructions Manual

61
4
Chapter 4 Adjustments and Settings for Recording (continued)
4-10-4 How to Use Scene File Data
It is possible to write the settings data into the scene file area
of the internal memory of the AJ-SPC700P, or to read data
written in this area. Four types of scene files are available.
This data allows you to quickly reproduce an optimum setup
state.
TITLEs 1 - 4 are factory-assigned the defaults for the AJ-
SPC700P.
To change the settings, go to the  screen from the
FILE page.
To write settings data...

62
Chapter 4 Adjustments and Settings for Recording (continued)
To read settings data for scene files
1Navigate the menu to the  screen. 
2Turn the JOG dial button to move the cursor to the
option SCENE SEL.
3Press the JOG dial button to blink scene file numbers.
Then, turn the dial button to select a desired scene file
number.
4Press the JOG dial button to accept the scene file.
5Turn the JOG dial button to move the cursor to the
READ option.
6Press the JOG dial button to display the following...

63
4
Chapter 4 Adjustments and Settings for Recording (continued)
To title settings data for scene files
1Navigate the menu to the  screen. 
2Turn the JOG dial button to move the cursor to the
option [TITLEs 1 - 4] for the appropriate scene file. 
3Press the JOG dial button to move the cursor to the title
entry area, putting the AJ-SPC700P in entry mode.
4Turn the JOG dial button until a desired character
appears. 
The characters that appear are switched in the
following order:Space: †
Ð
Alphabetical...

64
Chapter 5 Preparation
5-1 Power Supply
A battery pack or an external DC power supply can be used
as this unit’s power supply.
Using a Battery Pack
Battery packs from the following manufacturers can be used:
• Anton/Bauer
• IDX
• PA C O
• Sony

zOther batteries may be used by changing the menu
setting, but system compatibility is not guaranteed. 
z Charge the battery pack with the battery charger before
using it. (Please refer to the battery charger’s instruction
manual for information about...

65
5
Chapter 5 Preparation (continued)
When using a BP-90 type battery pack
1Remove the battery holder. 
2Attaching the battery case to the camera-recorder.
Connect the cable on the camera-recorder to the
cable on the battery case (BP-90 type). 
 Using a screwdriver, secure the battery case  (BP-90
type) to the camera-recorder. 
Open the cover and lift the rubber cap so that the
screw tightening hole is visible. Tighten the screws
to secure the battery case to the camera-recorder.
Be sure to fully...

66
Chapter 5 Preparation (continued)
Using an NP-1 type battery pack
1Remove the battery holder. 
2Mount the NP-1 type battery case on the camera-
recorder. 
Tighten the mounting screws. 
 Tighten the power contact screws. 
	 Insert the upper part of the removed cover in the
direction of the arrow. 

 Align the holes in the bottom part (metal part) of the
cover with the holes in the case, and secure the
cover with the screw. 

When mounting the battery holder, take care not to
pinch the connection...

67
5
Chapter 5 Preparation (continued)
5-1-2 Use of the external DC power supply
1Connect the external DC power supply to the DC IN
socket on the unit.
2Turn ON the power switch of the external DC power
supply. (If the power switch is available on the external
DC power supply)
3Turn ON the POWER switch on the unit.

zIf both the battery pack and the external DC power
supply are connected, the electric power is supplied
from the external DC power supply. While the
external DC power supply is used, the...

68
Chapter 5 Preparation (continued)
5-3 Mounting the lens and Performing the Flange Back 
and White Shading 
Adjustments
Mounting the Lens
1Raise the lens clamping lever and remove the mount
cap. 
2To mount the lens, align the indentation at the top
center of the lens mount with the center mark of the
lens. 
3Lower the lens clamping lever to clamp the lens. 
4Secure the cable through the cable clamp, and plug it
into the LENS connector. 
5Adjust the lens flange back. 

zPlease refer to the lens...

69
5
Chapter 5 Preparation (continued)
Adjusting the Lens White Shading
Take the following steps to adjust the white shading: 

Vertical coloring may occur near the open position of the
lens iris, even after adjusting the white shading. This
phenomenon, however, is a characteristic of the lens or
optical system. It does not indicate a malfunction. 
1Mount the lens on the camera. 
Be sure to connect the lens cable. 
2Set the electronic shutter to [OFF], the gain to [L (0dB)],
and the ASPECT option to...

70
Chapter 5 Preparation (continued)
This completes the white shading adjustment. 
The compensation values are stored in the non-volatile
internal memory. Therefore, re-adjusting the white shading is
not required, even after the camera-recorder power has
been turned off. 
Storing the Lens File Data 
The white shading compensation values can be stored in the
internal memory as lens file data. 
1Activate the MENU and go to the FILE page to open the
 screen. Turn the JOG Dial to move the cursor
to the item...