Panasonic Aj Sd965 Operating Instructions Manual

41
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
015
MONI
CONTROLThis sets whether the recorder is to be
forcibly set to the EE mode and the player’s
playback signals are to be output to the
monitor by pressing the recorder’s PLAYER
button when a monitor has been connected
only to the recorder during deck-to-deck
editing.
0000MANU:
The recorder is not forcibly set to the EE
mode.
0001 AUTO:
The recorder is forcibly set to the EE mode,
and the...

42
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
100
SEARCH ENAThis selects the direct search dial operation.
0000DIAL:
For direct search dial operations.
0001 KEY:
Operation is not transferred to the search
mode unless the search button is pressed.
101
SHTL MAX This sets the maximum speed for shuttle
operations.
0000
a8.4:8.4a normal speed0001a16:16a normal speed0002 a32:32a normal speed
102
FF. REW MAX This sets the maximum speed for FF and
REW...

43
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
111
FRZ MODE
SELThis selects the output picture in the
STANDBY OFF (HALF LOADING) and EJECT
modes.
0000DIS:
The video output is muted.
0001 STB OFF:
When the STANDBY OFF (HALF LOADING)
mode is established, the picture being played
back at the time is frozen and output.
0002 SOF&EJ:
When the STANDBY OFF (HALF LOADING)
or EJECT mode is established, the picture
being played back at the time is frozen...

44
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
114
REC INH LAMPThis selects whether to cause the REC INH
lamp to flash or light up when the cassette
has been set to the accidental erasure
prevention status.
0000LIGHT:
The lamp lights up.0001 FLASH:The lamp flashes.

When the REC INH switch is set to ON, the REC
INH lamp always lights regardless of the general
setting status.
115
EJECT SW INH This selects whether to enable or disable the...

45
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
200
PARA RUNThis selects whether two or more VTRs are
to be operated in synchronization.
0000DIS:
No operation in synchronization0001 ENA:Operation in synchronization

When operating two or more VTRs in
synchronization, set all the VTRs to ENA.
202
ID SEL This sets the ID information to be returned to
the controller.
0000 OTHER
0001DVCPRO0002 ORIG
O
ID information of any VTR except for the
DVCPRO’s...

46
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
301
IN/OUT DELThis selects the operation to be performed
when an edit point has been set incorrectly
(when the OUT point is before the IN point).
0000 MANU:
Editing is not executed unless the illegal edit
point is cleared or set again properly.
0001AUTO:
The edit points already input are automatically
cleared.
303
STD/
NON-STD This selects STD or NON-STD in accordance
with the composite input...

47
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
320
VAR FWD MAXThis sets the maximum SLOW FWD speed.
0000+4.1:
+4.1 (+3.1)a speed0001 +1.85:+1.85a speed0002 +1:+1a speed

O The value for the DV/DVCAM tape is shown in
parenthesis (    ).
O At any speed setting other than +4.1, the
phase cannot be synchronized from the
editing controller.
323
JOG FWD MAX This sets the maximum JOG FWD speed.
0000 +4.1:
+4.1 (+3.1)a speed0001 +1.85:+1.85a...

48
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
401
SRC PROTECTWhen the time selected as the setup menu
item No. 400 (STILL TIMER) setting elapses
while the unit is in the search STILL
(JOG/SLOW/SHTL) mode, the unit
automatically enters one of the tape
protection modes. This menu item is for
selecting which tape protection mode the
unit is to enter.
0000STEP:
STEP FWD0001 HALF:HALF LOADING

When STEP FWD is selected, the unit
automatically goes...

49
Setup menus(continued)
The underlined items indicates the initial setting.
USER menu
No./ItemDescription
506
BINARY GPThis sets the usage status of the user bit of
the time code generated by the TCG.
0000000:
NOT SPECIFIED (character set not specified)
0001 001:
ISO CHARACTER (8 bits character set based
on ISO646, ISO2022)
0002 010: UNASSIGNED 1 (undefined)0003 011:UNASSIGNED 2 (undefined)0004 100:UNASSIGNED 3 (undefined)0005 101:PAGE/LINE0006 110:UNASSIGNED 4 (undefined)0007 111:UNASSIGNED 5...

50
511
VITC OUTThis selects how the VITC which is to be
superimposed onto the output video signal is
to be output.
0000SBC:
During recording: The input time code, which was selected by
the setup menu No. 505 (EXT TC SEL)
setting and TCG switch, is output as the
VITC.
During playback: The time code recorded in the SBC area is
output as the VITC.
0001 VAUX:
During recording: The time code detected from the input video
signal is output as the VITC.
During playback: The time code recorded in the VAUX area
is...