Panasonic Aj Sd965 Operating Instructions Manual

11
Front panel
Parts and their functions(continued)
RINPUT SELECT buttons
These buttons switch the video and audio input
signals. It is also possible to switch the input signals
to the internal reference signal selected on setup
menu No. 600 (INT SG).
VIDEO: Each time the VIDEO button is pressed, the input
video signal selection is switched in the order of Y
PB PR 5 CMPST 5SDI  5SDTI/1394  5SG
(SG/SG1/SG2). O When SG has been selected, the signal is
switched to the internal reference signal
selected on...

CH1/3, CH2/4 lamp displays
∫: ON, ∑: OFF
12
Front panel
Parts and their functions(continued)
SAUDIO MIX switch
This is used to switch the input signals to be
recorded on the CH1, CH2, CH3 and CH4 audio
channels in conjunction with the REC CH1/CH3 and
REC CH2/CH4 buttons T.1&2: The audio input signals are switched to CH1 by
the REC CH1/CH3 button.
The audio input signals are switched to CH2 by
the REC CH2/CH4 button.
3&4: The audio input signals are switched to CH3 by
the REC CH1/CH3 button.
The audio...

13
Front panel
UAUDIO MON SEL (L and R) buttons
These buttons are used to select the audio signals
which are to be output to the MONITOR L and R
connectors.
Each time the L button is pressed, the signal to be
output to the MONITOR L connector is changed in
the following sequence: CH1 5 CH2 5CH3  5
CH4 5 CUE.
Similarly, each time the R button is pressed, the
signal to be output to the MONITOR R connector is
changed in the following sequence: CH1 5 CH2 5
CH3 5 CH4 5CUE.
Which signal has now been selected...

14
Front panel
Parts and their functions(continued)
\ENC CONTROL switchREMOTE: Set to this position to adjust the video output
signals using a device which has been connected
to the 9-pin REMOTE, RS-232C or PARALLEL
connector.
LOCAL: Set to this position to adjust the video output
signals using the unit’s controls (], ^, _, `).
]VIDEO LEVEL control and switch
These are used to adjust the video output level.
When the ENC CONTROL switch 
\is set to
LOCAL and the VIDEO LEVEL switch is set to
MANUAL, the...

cSHIFT button
When the SHIFT button is pressed together with the
buttons shown below, other operations can be
performed.
This combination is used to set the time code or
user bit value.
Press the PLAYER button while holding down the
SHIFT button to stop the advance of the time code
or user bit, and change the value using the search
dial.
O For further details, refer to the “Time code/user
bit” section (page 62).
TC PRESET
+
SHIFTPLAYER
TC PRESET
This combination is used to set the unit to the menu
mode....

16
Display panel
1TV system displays
The selected TV system is displayed here.
It is possible to switch between the 525 interlace
and 625 interlace systems by setting setup menu
item No. 070 (TV SYSTEM).
:This lights when the 525 interlaced TV system
has been selected.
: This lights when the 625 interlaced TV system
is selected.
2 WIDE lamp
This lamp lights when 16:9 wide-screen information
is being recorded on a tape.
Recording of wide-screen information can be
selected on setup menu No. 645 (WIDE...

17
:EDIT, EDIT REC, REC and REC INH lamps
EDIT: This lights when an editing mode has been
selected.
EDIT REC: This lights when the edit recording mode has
been established.
REC: This lights when the recording mode has been
established.
REC INH: This lights in the recording inhibit status (when
the REC INH switch at the bottom front panel is
set to ON or the cassette is in the accidental
erasure prevention status).
In this status, recording and editing are not
possible.
Whether the REC INH lamp is to...

18
Rear panel
1AC IN socket
Connect one end of the power cord supplied to this
socket and the other end to the power outlet.
2 DIGITAL AUDIO IN and OUT connectors
These are the input and output connectors for digital
audio signals that comply with the AES/EBU
standards.

The digital audio signals which are to be input to
these connectors must be synchronized with the
video input signals. Otherwise, noise will be
generated in the audio output signals.
3 ANALOG COMPONENT VIDEO IN connectors
(optional)
The...

19
Rear panel
 ANALOG COMPONENT VIDEO OUT connectors
The analog component video signals are output
through these connectors.
? ANALOG COMPOSITE VIDEO OUT connectors
The analog composite video signals are output
through these connectors.
The waveform monitor (WFM) signal can be output
from the VIDEO OUT 2 connector.
It can be selected using setup menu No. 00 (WFM
SEL).
Video signals containing superimposed information
can be output through the VIDEO OUT 3 connector.
Whether the superimposing is to be set...

20
Source machine:Set the REMOTE button 3 on the front panel to the remote mode (REMOTE lamp ON).
Recorder: Set the REMOTE button 3 on the front panel to the local mode (REMOTE lamp OFF).
Connections
PUSH PUSH
PUSH PUSH PUSHAC IN
SIGNAL
GND
AES/EBUSDI
ANALOGCH1/2
IN
Y VIDEO
VIDEO OUT
SERVICE ONLY
REMOTE IN/OUTCH1 CH2
AUDIO
IN
ENCODER REMOTE
RS-232C
PARALLEL
REMOTE OUT
IN
REF VIDEOIN
ON
OFF
P B
P R
Y1 2
(WFM)
3(SUPER)
PB
P R
OPTION
CH3/4
IN
CH1/2 OUT
CH3/4 OUT
REMOTE
75Ω
ON
OFF75Ω
ANALOGTCIN IN
ACTIVE...