Panasonic Aj Sd965 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Sd965 Operating Instructions Manual. The Panasonic manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 21
21 Connections with editing controller Connections(continued) ONPOWERREMOTESUPERREC INHTCGMODEONOFF DVCPRO 50EJECT SEARCHTCCUEVIDEOASSEMCOUNTERCH 1 CH 2 CH 3 CH 4PF 1 PF 2 PF 3 PF 4RESETPLAYERRECORDERSETTC PRESETMENUPFSTAND BYEDITA OUT OUT IN SET A INPREROLLAUTO EDIT PREVIEW/ REVIEWINPUT SELECT METERAUDIO MON SEL AUDIO MIX HEADPHONES AUDIO VOL SEL VIDEOCH 1R MIX 1&2CH1/3PULLCH2/4REC CH1/3CH1/3 CH2/4REC CH2/43&4 LCH 2 CH 3 CH 4AUDIO FULL/FINEREC PLAY REW FF SHIFT PULLSTOP INSERTPUSH DVCPRODV2XOFF...
Page 22
22 ONPOWERREMOTESUPERREC INHTCGMODEONOFF DVCPRO 50EJECT SEARCHTCCUEVIDEOASSEMCOUNTERCH 1 CH 2 CH 3 CH 4PF 1 PF 2 PF 3 PF 4RESETPLAYERRECORDERSETTC PRESETMENUPFSTAND BYEDITA OUT OUT IN SET A INPREROLLAUTO EDIT PREVIEW/ REVIEWINPUT SELECT METERAUDIO MON SEL AUDIO MIX HEADPHONES AUDIO VOL SEL VIDEOCH 1R MIX 1&2CH1/3PULLCH2/4REC CH1/3CH1/3 CH2/4REC CH2/43&4 LCH 2 CH 3 CH 4AUDIO FULL/FINEREC PLAY REW FF SHIFT PULLSTOP INSERTPUSH DVCPRODV2X OFF RECPBUNITYVA R ONOFFINTEXTTAPEEE XL/L/M-cassette SHTLJOGSLOW L...
Page 23
23 Jog mode Jog/Shuttle 1Press the search dial so that it remains pressed in. Check that the JOG lamp has lit. Shuttle mode 1Press the search dial so that it is released from the pressed-in position. The SHTL lamp lights, and the shuttle mode is established. OImmediately after the power is turned on, turn the search dial and leave it at the center position. 3To transfer the VTR from the jog mode to another mode, press the button that corresponds to the mode concerned. 2Turn the search dial. The dial’ s...
Page 24
24 Manual editing 1Select the editing mode. ASSEMBLE:Assemble (frame-to-frame continuity) editing is performed in this mode. INSERT: Insert editing is performed in this mode. 2Select the channels to be edited. For insert editing, press the buttons corresponding to the channels to be edited so that their lamps light. 3Press the PLAY button. 4While monitoring the TV monitor, search the position (IN point) where the editing is to be started, and press the PLAY and EDIT buttons together at this position....
Page 25
25 Automatic editing (deck-to-deck) 1Set the POWER switch to ON. 2Use the INPUT SELECT buttons to select the video and audio input signals. 3Switch the time counter display to TC, CTL or UB. 5If the recording levels are to be adjusted using the level controls, set the AUDIO VOL SEL (UNITY/VAR) switch to the VAR position. If the recording levels are to be fixed, set the switch to the UNITY position. 6Set the REMOTE button to the local mode (REMOTE lamp OFF). Switch settings and adjustments When using the...
Page 26
26 Automatic editing (deck-to-deck)(continued) 1Select the editing mode. For assemble editing, press the ASSEM button. For insert editing, press the INSERT button. ASSEM:This sets the unit to assemble (frame-to-frame continuity) editing mode. INSERT: This sets the unit to insert editing mode. 2Select the channels to be edited. With assemble editing, the ASSEM lamp lights. With insert editing, press the buttons corresponding to the channels to be edited so that their lamps light. 3Select the VTR to be...
Page 27
27 Automatic editing (deck-to-deck)(continued) 1Press the IN (or OUT) button to check the edit point. The value of the registered edit point appears on the display panel. 2While holding down the IN (or OUT) button, press the PREROLL button and check the picture at the edit point. The tape is cued up to the edit IN (or OUT) point, and a still picture of the point appears. OIf STOP has been selected as the setup menu No. 315 (AFTER CUE-UP) setting and if the MODE switch has been set to EE, the VTR is set...
Page 28
28 Automatic editing (deck-to-deck)(continued) 1Re-registering an edit point Locate the new edit point by performing the jog or shuttle operation, and press the IN (or OUT) button and SET button at the same time to re-register the edit point. 2Modifying an edit point in 1-frame increments (trimming function) Press the TRIM button while holding down the IN (or OUT) button. Each time the + button is pressed, the point is moved ahead by one frame. Conversely, each time the – button is pressed, the point is...
Page 29
29 2Upon completion of the editing, press the REVIEW button. Review is then started by the recorder side. OTo stop the review at any time, press the STOP button. O When the edit OUT point is reached, the tape is post-rolled, after which it stops.1Press the AUTO EDIT button. Automatic editing is now executed. OTo suspend editing at any time, press the STOP button. O When the edit OUT point is reached, the tape is post-rolled, after which it stops. Post-rolling With assemble editing, editing continues for...
Page 30
30 $Displaying the audio split edit points The edit points appear on the display panel. Video IN point: Press the IN button. Video OUT point: Press the OUT button. Audio IN point: Press the A IN button. Audio OUT point: Press the A OUT button. If the editing mode is changed to assemble editing after the audio edit points have been registered, the audio edit points will be cleared. $ Cueing the tape up to the edit points Cue-up to video IN point: Press the PREROLL button while holding down the IN...