Optoma W401 Projector User Manual

41English
User Controls
Image Shift
Press ► into the next menu as below and then use ▲ or ▼or ◄ 
or ►to select item.
Image Shift
H: Press the ◄ ► to shift the projected image position hori- `
zontally.
V: Press the ▲ ▼ to shift the projected image position verti- `
cally.
V Keystone
Press the ◄ or ► to adjust image distortion vertically and make a 
squarer image. 

42English
User Controls
“3D sync. Invert” func- ™tion wouldn’t save the setting. It will set to “Off” when powers on and changes source. 
3D Format is only sup- ™ported on 3D Timing on page 68.“3D Format” is only  ™supported on non-HDMI 1.4a 3D timing.
DISPLAY | 3D 
3D Mode
DLP-Link: Select “DLP-Link” to use optimized settings for DLP  `
Link 3D Glasses. (refer to page 16).
VESA 3D: Select “VESA 3D” to use optimized setting for VESA  `
3D Glasses. (refer to page 16).
3D -> 2D
3D: Display...

43English
User Controls
SETUP
Language
Choose the multilingual OSD menu. Press ► into the sub menu 
and then use the ▲ or ▼ or ◄ or ► key to select your preferred 
language. Press “Enter” to finalize the selection.
Language
 Exit
Projection
 ` Front-Projection
This is the default selection. The image is projected straight on 
the screen.
 ` Rear-Desktop
When selected, the image will appear reversed.
 ` Front-Ceiling
When selected, the image will turn upside down.
 ` Rear-Ceiling
When selected, the image...

44English
User Controls
Menu Location
Choose the menu location on the display screen.
Screen Type
Choose the screen type from16:10 or 16:9.
Projector ID
ID definition can be set up by menu (range 0-99), and allow user 
control an individual projector by RS232. Refer to pages 70-73 for 
the complete list of RS232 commands.
“Screen Type” is for  ™WXGA only. 

45English
User Controls
SETUP |  
Audio Settings
Internal Speaker
Choose the “On” or “Off” to turn on or off the internal speaker.
Mute
Choose the “On” to turn mute on.  `
Choose the “Off” to turn mute off.  `
Volume
Press the ◄ to decrease the volume. `
Press the ► to increase the volume. `
Audio Input
The default audio inputs are on the back panel of the projector. 
Use this option to reassign any of the Audio Inputs to the current 
image source. 
Audio1: VGA1. `
Audio2: VGA2. `
Audio3: Video. `...

46English
User Controls
SETUP | Security
Security
On: Choose “On” to use security verification when the turning  `
on the projector.
Off: Choose “Off” to be able to switch on the projector without  `
password verification.
Security Timer
Can be select the time (Month/Day/Hour) function to set the 
number of hours the projector can be used. Once this time has 
elapsed you will be requested to enter your password again.
Change Password
First time: `
Press “1. ” to set the password.
The password has to be 4...

47English
User Controls
SETUP |  
Advanced
Logo
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
Default: The default startup screen. `
Neutral: Logo is not displayed on startup screen. `
User: Use stored picture from “Logo Capture” function. `
Logo Capture
Press ► to capture an image of the picture currently displayed on 
screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are...

48English
User Controls
SETUP | Network 
LAN Settings
Refer to next page.
Control Settings
Refer to page 52.
LAN Settings
Control Settings
SETUP
    Exit
Network 

49English
User Controls
SETUP | Network | 
LAN Settings
Network State
Display the network connection status.
MAC Address
Display an MAC address.
DHCP
Use this function to select your desired startup screen. If you 
change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open.
On: Assign an IP address to the projector from an external  `
DHCP server automatically.
Off: Assign an IP address manually. `
IP Address
Select an IP address.
Subnet Mask
Select...

50English
User Controls
1. Turn on DHCP to allow the DHCP 
server to automatically assign an IP, or 
manually enter the required network 
information.
Network Status
MAC Address
DHCP
IP Address
Subnet Mask Connected
  
  Exit
Gateway
DNS Off
2. 
Then choose apply and press “
” button to complete the configuration 
process.
3. Open your web browser and type in the 
projector’s IP address from the OSD 
LAN screen. The following web page will 
display as below:
4. If connecting the projector to external...