OKI C530dn User Manual

							71 – C330/C530 Menu Functions
FILE SYS 
MAINTE1 
(cont.)SD-M FOR-
MATTINGPCL
COMMON
PSEFormat the specified parti-
tion. Press the OK button and 
the following message dis-
plays.
ARE YOU SURE?
YES/NO
If NO is selected, the display 
will go back to the source 
menu. If YES is selected, the 
printer will automatically 
reboot and initialize the spec-
ified partition.
This item is displayed only if 
the SD card (option) is 
installed.
FLASH INI-
TIALIZEEXECUTE Initializes the resident FLASH 
MEMORY.
If 
NO is selected, the 
machine will go back to the 
source menu.
If 
YES is selected, the 
machine will be automatically 
rebooted and initialize the 
FLASH memory.
FILE SYS 
MAINTE2CHK FILE SYS EXECUTE Executing this function will 
resolve any mismatch 
between the actual and the 
displayed free space of the 
file system and recover the 
management data (FAT infor-
mation).
Note 1: It takes several sec-
onds to complete this func-
tion.
Note 2: This item is displayed 
only if the SD card (option) is 
installed.
SECTIONITEMSETTING
SEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							72 – C330/C530 Menu Functions
FILE SYS 
MAINTE2 
(cont.)CHK ALL SEC-
TORSEXECUTE Performs recovery of defec-
tive SD Card sector informa-
tion and a file system 
mismatch mentioned above.
SD CARD
ENABLE
DISABLEEven if a machine is inopera-
ble at installation because of 
a faulty SD Card, the 
machine can be made opera-
ble by setting this parameter 
to No (ignores the existence 
of the SD Card).
When No is set, access to the 
SD Card results in FAIL 
because the SD Card is 
regarded as not attached.
After setting change and exit 
from the menu, the printer 
will restart.
This item is displayed only if 
the SD card (option) is 
installed.
SECTIONITEMSETTING
SEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							73 – C330/C530 Menu Functions
FILE SYS 
MAINTE2 
(cont.)SD CARD 
ERASEEXECUTE Deletion of all data stored in 
the SD Card. Data cannot be 
recovered. DoD 5220.22-M 
sanitizing formula is used for 
clearing the card. The printer 
will restart after changing the 
setup menu.
The progress of the proce-
dure is displayed as a per-
centage.
The following message 
appears after pressing the 
OK button.
ARE YOU SURE?
YES/NO
If NO is selected, the display 
will go back to the source 
menu, and the procedure for 
clearing the disk will start 
again immediately after the 
reboot.
if YES is selected.
The following message 
appears if the CANCEL button 
is pressed.
CANCEL NOW?
YES/NO
If NO is selected, the proce-
dure will continue.
If YES is selected, the proce-
dure will discontinue and the 
printer will restart after for-
matting the SD card.
This item is displayed only if 
the SD card (option) is 
installed.
SECTIONITEMSETTING
SEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							74 – C330/C530 Menu Functions
FILE SYS 
MAINTE2 
(cont.)INITIAL LOCKYES
NOIf “YES” is selected, you will 
not be able to select “ADMIN 
MENU” - “FILE SYS MAINTE1” 
(above).
LANGUAGE 
MENULANG INI-
TIALIZEEXECUTE Initialize the message file 
loaded in FLASH MEMORY.
If NO is selected, the 
machine will go back to the 
source menu. The procedure 
for clearing the disk will start 
immediately after the menu 
and machine reboot.
PS MENU L1 TRAY
TYPE1
TYPE2Switches between Postscript 
types
SIDM MENU SIDM MAN-
UAL ID#0 ~ 
2 ~ 9 Set up Pn specified in MAN-
UAL by MANUAL-1 ID No.FX/
PPR Emu in CSFcontrol com-
mand fi(ESC EM Pn). 
SIDM 
MANUAL2 
ID#0 ~ 
3 ~ 9 Set up Pn specified MANUAL 
by MANUAL-2 ID No.FX/PPR 
Emu in CSF control com-
mand(ESC EM Pn).
SIDM MP 
TRAY ID#0 ~ 
4 ~ 9 Set up Pn specified 
T R A Y O ( M P  Tr a y )  b y  M P  Tr a y  
ID No.FX/PPR Emu in CSF 
control command(ESC EM 
Pn). 
SIDM TRAY1 
ID#0 ~ 
1 ~ 9 Set up Pn specified TRAY 1by 
Tray 1 ID No.FX/PPR Emu in 
CSF control command(ESC 
EM Pn).
SIDM TRAY2 
ID#0 ~ 
2  ~9 Set up Pn specified TRAY 2 by 
Tray 2 ID No.FX/PPR Emu in 
CSF control command (ESC 
EM Pn).
SECTIONITEMSETTING
SEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							75 – C330/C530 Menu Functions
Print Statistics Menu
This menu should only be changed by the System Administrators. 
In order to gain access to this menu, follow the instructions in 
“How to change the settings - administrator” on page 40, but hold 
down the Menu button instead of the OK button. In this case, the 
default password is 0000.
This menu is in ENGLISH only 
  
CHANGE 
PASSWORDNEW PASS-
WORDxxxxxxxx
xxxxSet a new password for 
entering the administrator’s 
menu.
Password should be from 6 to 
12 digits of alpha/numeric 
characters (or mix) 
The default value is “aaaaaa”
The printer will restart after 
the ADMIN MENU.
VERIFY PASS-
WORDxxxxxxxx
xxxxVerification of above.
SECTIONITEMSETTINGEXPLANATION
ENTER PASSWORD nnnn Enters a password to enter Print 
Statistics menu.
The default password is “0000.”
“Print Statistics” category is not 
shown when Print Statistics 
function is not supported.
USAGE REPORT
ENABLE/
DISABLEEnables/Disables the printing of 
the Usage Report.
When changing a setting value, 
the printer is rebooted.
SECTIONITEMSETTING
SEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							76 – C330/C530 Menu Functions
GROUP COUNTER ENABLE/
DISABLE
Specifies if the Group counter is 
displayed in the Usage Report 
Print.
Enable: Displayed,
Disable: Not displayed.
Conditions for display:
Enable must be selected in 
Print 
Statistics > Usage Report
.
SUPPLIES REPORT ENABLE/
DISABLE
Indication of frequency of con-
sumable exchange/non indica-
tion is set.
When Enable is set, also the 
maintenance counter is indi-
cated in together.
Conditions for display:
Enable must be selected in 
Print 
Statistics > Usage Report
.
RST MAIN CNT EXECUTE Zeros the counter
CHANGE 
PASSWORDNEW PASS-
WORD**** Sets a new password to enter 
Print Statistics menu.
VERIFY 
PASSWORD**** Verifies the change
SECTIONITEMSETTINGEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							77  –  C330/C530 Replacing Consumables and Maintenance 
Replacing Consumables and 
Maintenance Items 
Order Information  ______________
Only use genuine Oki Original products to ensure the best quality 
and performance from your hardware. Non Oki Original products 
may adversely affect your printers performance. 
Item C330 Order No. C530 Order No.
To n e r,  b l a c k
Standard Capacity
High Capacity44469801
—44469801
44469802
To n e r,  c y a n
Standard Capacity
High Capacity44469703
—44469703
44469721
Toner,  magenta
Standard Capacity
High Capacity44469702
—44469702
44469720
Toner, yellow
Standard Capacity
High Capacity44469701
—44469701
44469719
Image drum 44494201 44494201
Downloaded From ManualsPrinter.com Manuals 
						

							78  –  C330/C530 Replacing Consumables and Maintenance 
Toner Cartridge Replacement    _____
Have a sheet of paper handy so that you have somewhere to place 
the used cartridge while you install the new one.
Dispose of the old cartridge responsibly, inside the pack that the 
new one came in. Follow any regulations, recommendations, etc., 
which may be in force concerning waste recycling.
If you do spill any toner powder, lightly brush it off. If this is not 
enough, use a cool, damp cloth to remove any residue.
Do not use hot water, and never use solvents of any kind. They will 
make stains permanent.
Note:
When the LCD display indicates TONER LOW, or if print 
appears faded, first open the top cover and try tapping 
the cartridge a few times to evenly distribute the toner 
powder. This will enable you to obtain the best yield 
from your toner cartridge.
CAUTION!
To avoid toner wastage and possible toner sensor 
errors, do not change the toner cartridge(s) until 
“TONER EMPTY” is displayed.
WARNING!
If you inhale any toner or get it in your eyes, drink a 
little water or bathe your eyes liberally in cold 
water. Seek medical attention immediately.
Downloaded From ManualsPrinter.com Manuals 
						

							79  –  C330/C530 Replacing Consumables and Maintenance 
1.Press the cover release and open the printer’s top cover fully. 
2.Note the positions of the four cartridges. It is essential that 
they go back in the same order. 
  
WARNING
If the printer has been powered on, the fuser may 
be hot. This area is clearly labelled. Do not touch.
1. Yellow 
2. Magenta 
3. Cyan 
4. Black 
1
2
3
4
Downloaded From ManualsPrinter.com Manuals 
						

							80  –  C330/C530 Replacing Consumables and Maintenance 
(a) Slide the colored release collar (1) on the cartridge to 
be replaced fully towards the right hand side of the 
printer.
(b) Lift the right-hand end of the cartridge and then draw 
the cartridge to the right to release the left-hand end as 
shown, and withdraw the toner cartridge out of the 
printer. 
Downloaded From ManualsPrinter.com Manuals