OKI C530dn User Manual

							91  –  C330/C530 Replacing Consumables and Maintenance 
10.Finally, close the top cover and press down firmly so that the 
cover latches closed. 
Important! 
If you need to return or transport your printer for any 
reason, please make sure you remove the image 
drum unit beforehand and place it in the bag provided. 
This is to avoid toner spillage.
Downloaded From ManualsPrinter.com Manuals 
						

							92  –  C330/C530 Replacing Consumables and Maintenance 
Replacing the Transfer Belt Unit ____
The belt unit is located under the image drum assembly.
Switch off the printer and allow the fuser to cool for about 
10 minutes before opening the cover.
1.Press the cover release and open the printer’s top cover fully. 
WARNING!
If the printer has been powered on, the fuser will be 
hot. This area is clearly labelled. Do not touch.
Downloaded From ManualsPrinter.com Manuals 
						

							93  –  C330/C530 Replacing Consumables and Maintenance 
2.Holding it by its handles, lift the image drum assembly, 
complete with toner cartridges, up and out of the printer 
Place the assembly in a safe place away from direct sources 
of heat, and cover it to protect it from exposure to light.
CAUTION!
The green image drum surface at the base of each 
cartridge is very delicate and light sensitive. Do 
not touch it and do not expose it to normal room 
light for more than 5 minutes. If the drum unit 
needs to be out of the printer for longer than this, 
please wrap the cartridge inside a black plastic 
bag to keep it away from light. Never expose the 
drum to direct sunlight or very bright room 
lighting.
Downloaded From ManualsPrinter.com Manuals 
						

							94  –  C330/C530 Replacing Consumables and Maintenance 
3.Pull the locking levers at each side of the transfer belt up and 
towards the front of the machine. 
Downloaded From ManualsPrinter.com Manuals 
						

							95  –  C330/C530 Replacing Consumables and Maintenance 
4.Using the locking levers, lift the belt upwards and withdraw it 
from the printer. 
 
Downloaded From ManualsPrinter.com Manuals 
						

							96  –  C330/C530 Replacing Consumables and Maintenance 
5.Unpack the new transfer belt. Position the transfer belt drive 
gear (1) toward the left rear of the printer and lower the belt 
into the printer. 
 
Downloaded From ManualsPrinter.com Manuals 
						

							97  –  C330/C530 Replacing Consumables and Maintenance 
6.Push the lock levers toward the back of the printer. 
Downloaded From ManualsPrinter.com Manuals 
						

							98  –  C330/C530 Replacing Consumables and Maintenance 
7.Align the pegs on the sides of the image drum with the slots 
in the sides of the printer and place the image drum and 
toner cartridges back into the printer.
8.Close the top cover and press down firmly so that the cover 
latches closed. 
Downloaded From ManualsPrinter.com Manuals 
						

							99  –  C330/C530 Replacing Consumables and Maintenance 
Fuser Replacement ______________
The fuser is located inside the printer just behind the toner 
cartridges. 
1.Press the cover release and open the printer’s top cover fully. 
WARNING
If the printer has recently been powered on, some 
fuser components will be very hot. Handle the fuser 
with extreme care, holding it only by its handle, 
which will only be mildly warm to the touch. A 
warning label clearly indicates the area. If in doubt, 
switch the printer off and wait at least 10 minutes 
for the fuser to cool before opening the printer 
cover.
Downloaded From ManualsPrinter.com Manuals 
						

							100  –  C330/C530 Replacing Consumables and Maintenance 
2.Pull the two fuser retaining levers (1) towards the front of 
the printer so that they are fully upright. Holding the fuser by 
its handle (2), lift the fuser straight up and out of the printer. 
If the fuser is still warm, place it on a flat surface which will 
not be damaged by heat. 
3.Unpack the new fuser.
Downloaded From ManualsPrinter.com Manuals