OKI C530dn User Manual
Have a look at the manual OKI C530dn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 103 Oki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
51 – C330/C530 Menu Functions PPR Emulation Menu ITEMACTIONEXPLANATION CHARACTER PITCH10 CPI; 12 CPI; 17 CPI; 20 CPI; PROPORTI ONAL Specifies character pitch in IBM PPR emula- tion. FONT CONDENSE12CPI TO 20CPI 12CPI TO 12CPI Specifies 12CPI pitch for Condense Mode. CHARACTER SETSET-1 SET-2 Specifies a character set. SYMBOL SET IBM-437 (DEFAULT SYMBOL SET ONLY SHOWN)Specifies a symbol set. LETTER O STYLEDISABLE ENABLE Specifies the style that replaces 9BH with letter o and 9DH with a zero ZERO CHARACTERNORMAL SLASHED Sets the zero to be slashed or unslashed. LINE PITCH6 LPI 8 LPI Specifies the line spacing. WHITE PAGE SKIPOFF ONSelects whether blank pages are printed or not. CR FUNCTIONCR CR+LFSelects whether a received carriage return character (0Dh) also causes a line feed. LF FUNCTION LF LF+CRSelects whether a received line feed charac- ter (0Ah) also causes a carriage return. LINE LENGTH 80 COLUMN 136 COLUMNSpecifies the number of characters per line. Downloaded From ManualsPrinter.com Manuals
52 – C330/C530 Menu Functions FORM LENGTH11 INCH 11.7 INCH 12 INCH Specifies the length of paper. TOF POSITION0.0INCH ~ 1.0INCHSpecifies the distance of print from the top edge of the paper. LEFT MARGIN0.0INCH ~ 1.0INCHSpecifies the distance of print from the left hand edge of the paper. FIT TO LETTERDISABLE ENABLE Sets the printing mode that can fit print data, equivalent to 11 inches (66 lines), in the LETTER-size printable area. TE X T H E I G H TSAME DIFF Sets the height of a character. SAME: Regardless of CPI, same height DIFF: As CPI, character heights vary. ITEMACTIONEXPLANATION Downloaded From ManualsPrinter.com Manuals
53 – C330/C530 Menu Functions FX Emulation Menu Calibration ITEMACTIONEXPLANATION CHARACTER PITCH10 CPI; 12 CPI; 17 CPI; 20 CPI; PROPOR - TIONAL Specifies character pitch in this emulation. CHARACTER SETSET-1 SET-2 Specifies a character set. SYMBOL SETIBM-437 (Default Symbol Set only shown) Specifies a symbol set. LETTER 0 STYLEDISABLE ENABLE Specifies the style that replaces 9BH with letter o and 9DH with a zero ZERO CHAR- ACTER NORMAL SLASHED Sets the zero to be slashed or unslashed. LINE PITCH6 LPI; 8 LPISpecifies the line spacing. WHITE PAGE SKIPOFF / ONSelects whether blank pages are printed or not. CR FUNCTIONCR / CR+LFSelects whether a received carriage return character (0Dh) also causes a line feed. LINE LENGTH80 COL- UMN; 136 COL - UMN Specifies the number of characters per line. FORM LENGTH11 INCH 11.7 INCH 12 INCH Specifies the length of paper. TOF POSI- TION 0.0INCH ~ 1.0INCHSpecifies the distance of print from the top edge of the paper. Downloaded From ManualsPrinter.com Manuals
54 – C330/C530 Menu Functions USB Menu This menu controls the operation of the printer’s USB data interface. LEFT MARGIN0.0INCH ~ 1.0INCHSpecifies the distance of print from the left hand edge of the paper. FIT TO LET- TER DISABLE ENABLE Sets the printing mode that can fit print data, equivalent to 11 inches (66 lines), in the LETTER-size printable area. TEXT HEIGHTSAME DIFF Sets the height of a character. SAME: Regardless of CPI, same height. DIFF: As CPI, character heights vary. ITEMSETTINGSEXPLANATION SOFT RESETENABLE DISABLE Enables or disables the SOFT RESET com- mand. SPEED 12 MBPS 480 MBPS Selects the interface speed. After setting change the menu, the printer restarts on exit. OFFLINE RECEIVEENABLE / DISABLE OFFLINE RECEIVE. SERIAL NUMBERENABLE DISABLE Specifies whether to ENABLE or DISABLE a USB serial number. The USB serial number is used to identify the USB device connected to your PC. Note When you have changed any settings in the USB Menu, turn the printer OFF, then ON again. ITEMACTIONEXPLANATION Downloaded From ManualsPrinter.com Manuals
55 – C330/C530 Menu Functions Network Menu ITEMACTIONEXPLANATION TCP/IPENABLE DISABLE Enables or disables this network protocol. IP VERSIONIP v4 IP v4+v6 IP v6 Sets up the IP version. Operates with IPv4 only (not valid with IPv6). Operates with both IPv4 and IPv6. Operates with IPv6 only (not valid with IPv4). From this stage, if IPv6 only is set from UI, for example Telnet, “IP v6” appears as the value of IP Version on the operation panel. “IP v6” will disappear from the value if “IP v4” or “IP v4+v6” is selected. Display Condition: TCP/IP should be enabled. NETBEUIENABLE DISABLE Enables or disables this network protocol. NETBIOS OVER TCPC330: ENABLE / DISABLE C530: ENABLE / DISABLE Sets Enable/Disable of NetBIOS over TCP protocol. Display Conditions: > TCP/IP should be enabled. > IP Version is not IPv6. NETWAREC330: ENABLE / DISABLE C530: ENABLE / DISABLE Enables or disables this network protocol. ETHERTALKENABLE DISABLEEnables or disables this network protocol. Downloaded From ManualsPrinter.com Manuals
56 – C330/C530 Menu Functions FRAME TYPEAUTO / 802.2 / 802.3 / ETHER - NET II / SNAP Selects the Ethernet MAC layer frame type. Display Condition: Netware should be enabled. IP ADDRESS SETAUTO / MANUALSpecifies whether IP address allocation is automatic (DHCP) or manually assigned. IPV4 ADDRESSxxx.xxx.x xx.xxxCurrent assigned IP address. To change, press OK and use Menu buttons to incre- ment 1st octet, then press OK again to move on to next octet. When 4th octet has been set, press OK again to register new address. SUBNET MASKxxx.xxx.x xx.xxxCurrent assigned subnet mask. To change, proceed as above. GATEWAY ADDRESSxxx.xxx.x xx.xxxCurrent assigned gateway address. To change, proceed as above. WEBENABLE / DISABLEEnables or disables Web config. facility. TELNETENABLE / DISABLE Enables or disables Telnet config. facility. FTPENABLE / DISABLE Enables or disables communication via FTP. IPSECENABLE / DISABLE Applies to C330 and C530 only. Sets Enable/Disable of IPSec. Enable via the web. Enable: IPSec is available. Disable: IPSec is not available. SNMPENABLE / DIS- ABLE Enables or disables SNMP protocol. ITEMACTIONEXPLANATION Downloaded From ManualsPrinter.com Manuals
57 – C330/C530 Menu Functions NETWORK SCALENORMAL / SMALLSelects network size. When NORMAL is selected, printer can work effectively, even when connected to a HUB that has a spanning tree feature. However, printer start up time gets longer when computers are connected with two or three small LANs. When SMALL is selected, computers can cover from two or three small LANs to a large LAN, but may not work effectively when connected to a HUB that has a span - ning tree feature. HUB LINK SETTINGAUTO NEGOTI - ATE 100BASE- TX FULL 100BASE- TX HALF 10BASE-T FULL 10BASE-T HALF Sets full or half duplex for communication via a network hub. When AUTO is set, negotiation is done auto- matically. FAC TO RY DEFAULTSEXECUTEReloads the settings present when the unit was setup by the manufacturer. ITEMACTIONEXPLANATION Downloaded From ManualsPrinter.com Manuals
58 – C330/C530 Menu Functions Memory Menu Sys Adjust menu ITEMACTIONEXPLANATION RECEIVE BUF SIZEAUTO 0.5MB 1MB 2MB 4MB 8MB 16MB 32MB Sets the size of the receive buffer. RESOURCE SAVEAUTO OFF 0.5MB 1MB 2MB 4MB 8MB 16MB 32MB Sets the size of the resource saving area. ITEMACTIONEXPLANATION X ADJUST+2.00MIL LIMETER ~ 0.00MILL IMETER ~ - 2.00MILLI METER Adjusts the position of a whole print image in the direction perpendicular to the direc - tion the paper runs, that is horizontally, in 0.25 mm increments. Any parts of the print image that are outside the printable area as a result of this shift will be cropped. Downloaded From ManualsPrinter.com Manuals
59 – C330/C530 Menu Functions Y ADJUST+2.00MIL LIMETER ~ 0.00MILL IMETER ~ - 2.00MILLI METER Adjusts the position of a whole print image in the direction the paper runs, that is verti - cally, in 0.25 mm increments. Any parts of the print image that are outside the printable area as a result of this shift will be cropped. Corrections in a negative value are ignored in PS mode. DUPLEX X ADJUST+2.00MIL LIMETER ~ 0.00MILL IMETER ~ - 2.00MILLI METER When printing the reverse page of a duplex job, adjusts the position of the whole print image in the direction that is perpendicular to the direction the paper runs, that is hori - zontally, in 0.25 mm increments. Any parts of the print image that are outside the printable area as a result of this shift will be cropped. DUPLEX Y ADJUST+2.00MIL LIMETER ~ 0.00MILL IMETER ~ - 2.00MILLI METER When printing the reverse page of a duplex job, adjusts the position of the whole print image in the direction the paper runs, that is vertically, in 0.25 mm increments. Any parts of the print image that are outside the printable area as a result of this shift will be cropped. Corrections in a negative value are ignored in PS mode. DRUM CLEAN- ING ON OFF Sets whether to rotate the drum in idle prior to printing in order to reduce any horizontal white lines. CAUTION: Each additional rotation will shorten the ID life by that amount. HEX DUMPEXECUTEPrints out data received from the host PC in hexadecimal Dump. Turning off the power supply switch restores Normal Mode from HEX Dump Mode. ITEMACTIONEXPLANATION Downloaded From ManualsPrinter.com Manuals
60 – C330/C530 Menu Functions Maintenance Menu ITEMACTIONEXPLANATION MENU RESETEXECUTEResets menus to default settings. SAVE MENUEXECUTESaves the current menu settings. The last menu executed is saved and the menu pre - viously saved is overwritten and erased. When you press the OK button, the following confirmation message is displayed. ARE YOU SURE? YES/NO If you select NO, the display returns to the previous menu. If you select YES, the current menu settings are stored and the menu is exited. RESTORE MENUEXECUTEChanges to the menu setting saved. When you press the OK button, the following confirmation message is displayed. ARE YOU SURE? YES/NO If NO is selected, the previous menu display resumes. If YES is selected, changes made to the menu setting are saved and you exit from the menu. Notes: This cannot be executed when data is print- ing. This menu item will only show if the menu has been saved previously POWER SAVE ENABLE / DISABLEEnables or disables automatic power save mode. Delay before entering this mode is set in the SYSTEM CONFIGURATION menu. SLEEPENABLE / DISABLESets Enable/Disable of Sleep Mode. PAPER BLACK SET–2~0~+2Used for small adjustments when you expe- rience faded print or light specks / streaking in monochrome printing on white paper. Select a higher value to reduce fading, or a lower value to reduce specks or streaking in high density print areas. Downloaded From ManualsPrinter.com Manuals