Nortel Modular Ics 6.1 Installer Guide

Lines / 361
P0603534  02Modular ICS 6.1 Installer Guide
Link at CO (loop trunks only)
Some exchanges respond to a Link signal (≤‡⁄) by 
providing an alternative line for making outgoing calls. 
• When Link at CO is set to Y (Yes), the system applies the 
restrictions on outgoing calls to the digits dialed after the 
Link signal, and the call on the alternative line will be 
subject to all restrictions. 
• Setting Link at CO to N (No) prevents a Link signal from 
resetting the Norstar restrictions in...

362 / Lines
Modular ICS 6.1 Installer GuideP0603534  02
Full AutoHold
Full AutoHold on idle line is a variation of the Automatic Hold 
feature. If you select an idle line, but do not dial any digits, that 
line is automatically placed on hold if you select another line. 
Press CHANGE
 to select the setting: N (No) or Y (Yes).
The line you first selected is held until you press the line 
button. The line is not available for use by anyone else. 
LossPkg
Loss Package allows you to select the appropriate...

Lines / 363
P0603534  02Modular ICS 6.1 Installer Guide
The following table describes the five types of loss packages.
Signal
Select the signal type for the line. 
Press CHANGE
 to select one of these settings: WinkStart, 
Immediate, DelayDial.
Loss
PkgReceive
LossTransmit
LossImpedance Distance to switch/
cable loss/terminating 
switch
ShortCO0 dB 3 dB Short Short/2 dB and 6 dB/ICS to CO
ShortPBX0 dB 0 dB Short Short/2 dB/ICS to PBX
Tips - This setting applies only to lines connected to an 
NT7B75GA-93...

364 / Lines
Modular ICS 6.1 Installer GuideP0603534  02
ANI Number
Select whether the telephone number of the caller will be 
collected for this line. The digits can then be displayed on 
Norstar telephones as part of Call Display services. 
Press CHANGE
 to select either: N (No) or Y (Yes). 
DNIS Number
Select whether the digits dialed by an external caller on this 
line will be collected. 
Press CHANGE
 to select either: N (No) or Y (Yes).
Tips - The central office must deliver ANI/DNIS in DTMF 
mode....

Lines / 365
P0603534  02Modular ICS 6.1 Installer Guide
Gain
Select the appropriate gain level for the line. 
Press CHANGE
 to select either: Normal or High. 
The default value Normal induces zero loss. Use it when the 
E&M trunks are connected to facilities that present 0 dBm at 
the interface for both the transmit and receive paths.
Normal gain level (0dBm)
The value High induces 7 dB of loss in the receive path and 
16 dB of loss in the transmit path. Use it when the E&M trunks 
are connected to...

366 / Lines
Modular ICS 6.1 Installer GuideP0603534  02
Programming distinctive ring patterns
When lines are configured on your system, they can be 
assigned one of four distinctive ring patterns (DRP). The 
default for all telephones is 1. The default for lines is None, 
which is the lowest priority.
Call ringing: When multiple calls are presented to the 
telephone, the call with the highest priority DRP setting will be 
the call that rings at the telephone. 
Call answering: When multiple calls are...

Lines / 367
P0603534  02Modular ICS 6.1 Installer Guide
4. Press ‘ until the display shows Lines.
5. Press ≠. The display shows Show line _____.
6. Press FIND
 until you reach the line to which you want to 
define a ring pattern.
7. Press ≠ and then ‘ until the display 
shows TrunkType:PRI.
8. Press ‘ until the display shows Dstnct ring: 
NONE.
9. Press CHANGE
 to toggle to the ring pattern number you 
want to assign to the line (None, 2, 3, 4).
10. Press ® to exit or ‘ to continue programming.
Name
The...

368 / Lines
Modular ICS 6.1 Installer GuideP0603534  02
Restrn filters
Restriction filters are groups of dialing restrictions and dialing 
overrides for external numbers or feature codes. By packing a 
set of restrictions and overrides in one group, you can assign 
them to a line in one step, as a single package.
You can make changes to restriction filters under both 
Terminals&Sets, and Lines. Any changes will take effect 
for any telephone, line, or line on a telephone, regardless of 
where the...

Lines / 369
P0603534  02Modular ICS 6.1 Installer Guide
Remote restrns
Specify the restriction filter to be applied to remote callers 
calling in to the Norstar system on this line. A restriction filter 
is a set or group of restrictions and overrides. 
As with line restrictions, you can apply a different remote 
restriction for normal service and for each of six schedules.
Use CHANGE
 and the dialpad to program the remote restrictions 
for each schedule. 
The default restrictions are shown in the...

370 / Lines
Modular ICS 6.1 Installer GuideP0603534  02
Telco features
This item allows you to assign features from a telco level.
VMsg center 1
If you subscribe to a voice message service, you can specify 
which voice message center is used for each external line that 
can receive message waiting indication. 
1. For each line, press CHANGE
 to select a message center: 
1, 2, 3, 4, 5, or N.
Note:  If your system is part of a network that provides a 
central voice mail system on another site, you must use...