Nitsuko Ds2000 Software Manual

9800 - System Utilities, Part 1
9801 - Copy Command
DS2000 Software Manual Chapter 2: Programming473
OR
If copying to a range of extensions or trunks, enter the highest numbered extension or trunk in 
the range.
8. Press 
HOLD.
9. Press
 CONF to select another program to copy.
OR
Press 
CONF twice to exit the program.
COPY (program)    (source)
COPY COMPLETE! 

9900 - System Utilities, Part 2
9901 - Reset Station Port
474Chapter 2: ProgrammingDS2000 Software Manual
9900 - System Utilities, Part 2
9901 - Reset Station Port
Description
Use Program 9901 - Reset Station Port to reset an extension. This program also gives you the 
option of reviewing the status of the extension before you reset it.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9901 + 
HOLD
3. Enter the number of the station port you want to program (1-32) +...

9900 - System Utilities, Part 2
9902 - Reset Trunk Port
DS2000 Software Manual Chapter 2: Programming475
9902 - Reset Trunk Port
Description
LCCPU 01.00.00 Not available. 

9900 - System Utilities, Part 2
9903 - System and PCB Reset
476Chapter 2: ProgrammingDS2000 Software Manual
9903 - System and PCB Reset
Description
LCCPU 01.00.00 Not available. 

9900 - System Utilities, Part 2
9904 - Side Tone Test
DS2000 Software Manual Chapter 2: Programming477
9904 - Side Tone Test
Description
LCCPU 01.00.00 Not available. 

9900 - System Utilities, Part 2
9905 - Password
478Chapter 2: ProgrammingDS2000 Software Manual
9905 - Password
Description
Use Program 9905 - Password to change the system passwords. The table below shows the default 
system passwords.  Turn to System Programming List on page 289 for more on the system pass-
words.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9905 + 
HOLD
3. Enter the level (1-3) for the password you want to change + VO L 
The level selected and...

9900 - System Utilities, Part 2
9906 - Database Save
DS2000 Software Manual Chapter 2: Programming479
9906 - Database Save
Description
Use Program 9906 - Database Save to back up site data to PC Card P/N 85880 or P/N 80050-
V**.**. Refer to your Hardware Manual for the specifics.
Conditions
The following table lists the PC Card Backup Error Messages that you may see when using the 
instructions below.
Telephone Programming Instructions
1. Insert the PC Card into the CPU.
Refer to the Hardware Manual for...

9900 - System Utilities, Part 2
9906 - Database Save
480Chapter 2: ProgrammingDS2000 Software Manual
You see the address, name and date of the first data base stored. If you data bases are 
stored, you see:
8. The system assigns the name you entered in step 7 to the address you select below:
- Press VOL 
 or VOL  to scroll through the 12 data base addresses (DB 00 through DB 11)
OR
- Skip this step to select the currently displayed data base.
9. Press 
HOLD.
Normally, you see:
The PC Card Active LED is...

9900 - System Utilities, Part 2
9907 - Database Load
DS2000 Software Manual Chapter 2: Programming481
9907 - Database Load
Description
Use Program 9907 - Database Load to load site data previously saved to PC Card P/N 85880 or P/
N 80050-V**.** into the system data base. Refer to your Hardware Manual for the specifics.
Conditions
The following table lists the PC Card Load Error Messages that you may see when using the 
instructions below.
Telephone Programming Instructions
1. Insert the PC Card into the...

9900 - System Utilities, Part 2
9999 - System Initialization
482Chapter 2: ProgrammingDS2000 Software Manual
9999 - System Initialization
Description
Use Program 9999 - System Initialization to initialize the system database.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9999 + 
HOLD
3. Enter Y  + HOLD to initialize the system.
OR
Enter N + 
HOLD to exit the program without initializing.
If you enter Y, the system will initialize with the factory-installed default...