Nitsuko Ds2000 Software Manual

3. Installing
Extensions and Trunks
3-7
FINISHING THE INSTALLATION
Reinstalling the Front Cover (Figure 3-7)
To reinstall the front cover:
1. Hook the tabs on the rear of the cover into their associated slots.
2. Push the front of the cover into place.
3. Screw in the two captive screws that secure the cover to
the cabinet.
Figure 3-7  REINSTALLING THE FRONT COVER
80000 - 12 A 

3-8
— For Your Notes — 

4. Optional
Equipment
Section 4, INSTALLING OPTIONAL EQUIPMENT
In this section . . .
Page
2-OPX Module  . . . . . . . . . . . . . . . . . . . . .4-14
Installing the 2-OPX Module . . . . . . . . . . . . 4-14
Programming 2-OPX Modules . . . . . . . . . . . 4-14
Wall-Mount Kit  . . . . . . . . . . . . . . . . . . . . .4-16
Installing the Wall-Mount Kit . . . . . . . . . . . . 4-16
Installing the Wall-Mount Handset Hanger . . 4-16
Wall-Mounting a Key Telephone. . . . . . . . . . 4-17
Desk Stand  . . . . . ....

4-2
EXTERNAL PAGING AND PAGE RELAYS
Installing External Paging (Figure 4-1)
The CPU provides an External Paging output and associated
relay contacts. You connect the Paging output to audio inputs
on customer provided Paging systems. In some Paging systems,
you can use the associated CPU relays to automatically turn the
amplifiers on and off. The control relays are normally open and
close whenever the External Paging is activated.To connect an External Paging amplifier:
1. Find an available connector in...

4. Optional
Equipment
4-3
EXTERNAL PAGING AND PAGE RELAYS
Figure 4-1  CONNECTING EXTERNAL PAGINGRJ61X 
Pin
Latch
faces upTo CPU
Mod Jack
Note
reversalPort
DesignationTo 66 Block
WHT-BLU (1T)
BLU-WHT (1R)WHT-ORN (2T)
ORN-WHT (2R)
WHT-GRN (3T)
GRN-WHT (3R)
WHT-BRN (4T)
BRN-WHT (4R)
80000 - 18B
4T
3T
2T
1R
1T
2R
3R
4R
1
2
3
4
5
6
7
8
Page OutMusic InRelay ContactsNo Connection
The following products should help if you make your own cables:Suttle SE-266-8K 8 Position Modular Plug (requires an SE-166
or...

4-4
EXTERNAL PAGING AND PAGE RELAYS
Installing External Paging Control Relays (Figure 4-2)
You can program the CPU relays to automatically close when
External Paging or night ringing is active. The control relays
are normally open and close when active.To connect an External Paging Control Relays:
1. Find an available connector in a station cable and make sure
it is correctly punched down at the 66M1-50 block.
Follow standard color code order. Be sure the block is
properly cross-connected.
2. For the...

4. Optional
Equipment
4-5
EXTERNAL PAGING AND PAGE RELAYS
Figure 4-2  CONNECTING CONTROL RELAYS
RJ61X 
Pin
Latch
faces upTo CPU
Mod Jack
Note
reversalPort
DesignationTo 66 Block
WHT-BLU (1T)
BLU-WHT (1R)
WHT-ORN (2T)
ORN-WHT (2R)
WHT-GRN (3T)
GRN-WHT (3R)WHT-BRN (4T)
BRN-WHT (4R)
80000 - 18
4T
3T
2T
1R
1T
2R
3R
4R
1
2
3
4
5
6
7
8
Page OutMusic InRelay ContactsNo Connection
The following products should help if you make your own cables:Suttle SE-266-8K 8 Position Modular Plug (requires an SE-166
or...

4-6
DOOR BOX
Installing the Digital Door Box (Figure 4-3)
Any available 16DSTU PCB port can support a Digital Door
Box (P/N 92246).To install the Digital Door Box:
1. Snap open the Door Box case.
2. Punch down one end of a two-pair twisted station cable on
the extension block as shown in Figure 4-3.
3. Run the station cable through the hole in the back of the
Door Box.
When wall mounting, use the two holes in the base of
the Door Box for the mounting screws.
4. Strip the conductors back about 1/2 inch...

4. Optional
Equipment
4-7
DOOR BOX
Figure 4-3  CONNECTING A DOOR BOX
80000 - 39A
9
10
11
12
13
14
White/Blue
Mounting screws
(Customer provided)
Digital Door Box
(P/N 92246) Digital Door Box
(Extension 304)
Station Cable
Lead Designations
Blue/White
White/Blue
Blue/White
TT
TR 

4-8
MUSIC SOURCES
Installing a Music Source (Figure 4-4)
The CPU provides connection for a customer provided music
source. Use this music source for Background Music and Music
on Hold.To connect a music source:
1. Find an available connector in a station cable and make sure
it is correctly punched down at the 66M1-50 block.
Follow standard color code order. Be sure the block is
properly cross-connected.
2. For the connector chosen, locate pins 2T and 2R (see Figure
4-4) and connect the music source.
3....