Nitsuko 24i/28i/124i/384i Hardware Manual

4. Optional
Equipment4-29
3-ACI MODULE
To connect a MOH source to a 3-ACI Module:
1. Plug the music source audio output into an available RCA
jack on the 3-ACI.
2.To program Music on Hold . . .
With the default settings,
Music on Hold uses the internal Minuet selection.
0302 - Item 1: Music on Hold Tone
Enter 0 to enable external MOH.
0914 - Setting the Music on Hold Source
For each trunk, enter the ACI port number (1-6) to enable
the CPRU MOH source.
Refer to Music on Hold in the Software Manual for...

4. Optional
Equipment
4-30
3-ACI MODULE
Installing the 3-ACI Module for Music On Hold
and External Paging (Cont’d)
2.To program the 3-ACI Module for External Paging . . .
With the default settings, no 3-ACI Modules are 
programmed.
0504 - ACI Extension Number
To allow users to dial ACI ports directly, assign extension
numbers to the ACI software ports (1-6). You should use
extension numbers higher than 372.
1301 - ACI Port Function
Assign each ACI software port for output (2).
Refer to Analog...

4. Optional
Equipment4-31
REJ RECORDING JACK
Using the REJ Recording Jack
Use the REJ Recording Jack to connect a telephone to an external
tape recorder or speaker. There are two versions of the REJ record-
ing jack. The REJ P/N 92265 can only be connected to a Super
Display Telephone (P/N 92663 or 92283x), while P/N 80175 (for the
i-Series phones) can be connected to 28- or 34-Button i-Series
phones. The REJ output is a standard RCA jack which you can con-
nect directly to an AUX level input on a...

4. Optional
Equipment
4-32
REJ RECORDING JACK
Installing the REJ (Cont’d)
Figure 4-23  PUNCHING OUT FOR THE REJ
(PHONE SERIES 922xx)4. Install the REJ as shown with the components facing down.
Refer to Figures 4-24, 4-25, and 4-26.
5. Use the screw supplied with the REJ to secure it to the lower
telephone housing.
6. Insert the connector on the REJ’s cable into the matching
connector on the PCB in the telephone’s upper housing.
To ensure the proper polarity, the connector is keyed  (The red
wire is on...

4. Optional
Equipment4-33
REJ RECORDING JACK
Figure 4-24  INSTALLING THE REJ
(PHONE SERIES 926)Figure 4-25  INSTALLING THE REJ
(PHONE SERIES 922xx)
92000 - 132
Red Wire
REJU
92 - 132A
Red Wire
REJU 

4. Optional
Equipment
4-34
REJ RECORDING JACK
Figure 4-26  INSTALLING THE REJ
(i-SERIES PHONES)
Red Wire
REJ
926 - 88 

4. Optional
Equipment4-35
WALL-MOUNT KIT
Using the Wall-Mount Kit
Any key telephone can be equipped with a wall-mount kit for
attachment to a wall. The wall-mount kit includes a mounting
bracket, wall-mount screws, washer, and handset hangers. Each
i-Series phone has an integrated wall/desk bracket. Optionally,
you may also be able to install the bracket on the phone so that
the phone can be placed on the desk. This angles the phone to
provide easier viewing of the keys and the display.
Note:The...

4. Optional
Equipment
4-36
WALL-MOUNT KIT
Installing the Wall-Mount Handset Hanger For 922xx
Series Phones (Figure 4-28)
1.Two different types of handset hangers may be included in
your kit. To ensure that you are using the correct hanger,
refer to Figure 4-28. Insert the handset hanger in the slot
provided beneath the telephones hookswitch. Make sure the
clip snaps into place.
If necessary, use a screwdriver to remove the handset
hanger.
Note:The handset hanger must be installed as shown, with the
hook...

4. Optional
Equipment4-37
WALL-MOUNT KIT
Wall-Mounting a 926/922 Series Key Telephone
(Figure 4-29)
1.Installing Over
 a 
Wall Plate:
Slide the metal bracket down over the retaining screw heads
on the wall plate until secure. Note that the dimpled outdents
in the bracket should be against the wall.
Installing Over
 a Modular
 Jack:
Skip to Step 2.
2. Depending on your installation, attach the wall-mount kit’s
plastic bracket to either the metal bracket or directly to the
wall using the screws provided....

4. Optional
Equipment
4-38
WALL-MOUNT KIT
Using the Desk Stand on 926/922 Series Phones
(Figure 4-30)
1. Place the rubber feet provided in the kit on the bottom of the
plastic bracket. Place a rubber foot on each corner.
2. Insert the telephone’s line cord from the 625 modular jack
through the plastic bracket using the clips provided on the
bracket.
3. Place the telephone on top of the plastic bracket on the clips
provided. Slide the telephone down until it snaps into place.
Figure 4-30  ATTACHING AS A...